Hi. I would like to join this group

The FDM-DUO works in stand alone mode as it should. I have installed the ELAD FDM-SW2. RX ist fully working but TX audio is missing. I could not figure out the problem, but anyway, my goal is to use S

I thought I'd ask the folks here if anyone is using the often sold receiver front end protector found all over the web like this one: it supposedly uses the following schematic: The reason I am asking

The instructions at https://www.sdr-radio.com/cw-skimmer for using Console to feed I/Q data to CW Skimmer are very clear and following them worked for me. But they seem to assume using Rx 1 as the sou

HI Simon a little off topic on the SdrConsole, sorry, but didn't know where to ask so as not to disturb Simon directly ... I have always dedicated my fourth PC monitor, a 40 "HDMI TV, for the excellen

https://www.russianwarchatter.info/ Weak but readable on Simon's server 9741kHz USB. 73 Kriss KA1GJU

Hello I am visually impaired and use a screen reader can any one tell me if there are keyboard shortcuts or a web interface fore setting up and using sdr-radio? thanks Hank

Running an amp on digital modes, or a clueless operator? Or just a really W I D E digital signal? 73 Kriss KA1GJU See attachments:

The Keysite picture was showing the spurs from a Hermes at 28.4 MHz with a 192kHz sample rate using the V1 firmware. it has nothing to do with the IC7300. I have spare time now so I will repost the im

I've been using SDR's for a couple years now, but I still consider myself a beginner. I would like to use an SDR to transmit/receive AX.25. Ideally, it would be great advantage to use Direwolf. Is thi

I've been following the discussion on support for the EP3C25 Transceiver Card. Will SDRC support the ANAN-10? I assume I would have to install protocol2. Mike N2M2

HI A phenomenon that I don't understand: I made an I/Q recording, then I deleted part of it with the I/Q file editor, keeping only one hour. The signal levels shown on the 2 pictures attached are very

Hi, Start the Data File Editor again, let me see the settings. Can you possibly upload the original file for me? Simon Brown, G4ELI https://www.sdr-radio.com

I've used various sdrs now for about 20 years. To anyone thinking about software defined radio - I run a Hermes Lite 2 with SDR Console and I must say the combination is very enjoyable to use and the

Hi, was in trouble after an update to SDRConsole 3.1. The end of the game was SDRuno does not find any RSP (my is a RSPdx) an SDRconsole does not show a spectrum. Takes me some hours to clean up my PC

I was looking at the TX audio section, which I have not used yet. I cannot see a noise gate or downward expander, perhaps I missed it. If it is not present is there any possibility of adding one? Shou

Super Station #3 2/20/2022 9:08:09 AM 180.150.127.225 Guest (Perth, Australia) Every AM BC station known to man is visible in this screen shot when I connected today! The AGC works just fine in the Ai

Looking for someone to correspond with to help me set up my remote located RSPdx I access via SDR Console. The site is RX only with 8 circle RX array an run by a small I5 NUC pc. I cannot seem to get

1650 KBJD Denver CO 15180km [9432 miles] Received in Botswana. A new best distance for me. Airspy HF+ Discovery, SDR Console V3, random wire with binocular balun. Special thanks to Alessandro G. and A

SDR Console server is streaming 8 MHz bandwidth from my RX-888 with no stutter what so ever. Well done Simon. I'm guessing the server can't go any higher in bandwidth. The receiver can. -- Thanks Stev