Hi Simon Caught very tail end of you DXing on 80m this morning (at least I'm pretty sure it was you...... just caught the very tail end of QSO with a G station DXer). Fairly sure you were using your m

Hi Jirka, No help from here, tried your server with Console and no connection for me either. Checked with SDR# and it is working fine. Not a bad setup at all. Well done! Best 73´s Pekka Lähetetty Wind

Hi all, I have a public Spyserver sdr://81.201.61.159:5556. But I´m not able to connect from the Console, only from Sharp. What I´m doing wrong? From sharp everything run without problems. Example for

I have looked through many of the CW Skimmer and SDR-Console posts and have not found one that matches my situation although some have come close. I am convinced it is operator error, but for the life

Hello, I am wanting to run my SDRdou and compare 2 different antennas on the same frequency. and use the Signal view to capture a data stream and compare the CSV in excel post recording I cannot seem

Look at this gem this AM! Well, after all, it is called the "Children's Band" is it not? 100kHz wide on voice peaks, with spurs as far as +/- 125kHz ! But alas, his AM signal was not intelligible. 🤪 7

Running a IC7300 with an internal PTRX-7300 panadapter connected to an RSP1A SDR. I have two RSP1A's and at SDR Console startup I select whichever I want to use. 99% of the time it's the RSP1A connect

Dave says "FCDPP now working"! Microphone permissions all along on Win 10. Grateful thanks to all respondents. 73 Dave G7GZC

If a user connects to a server and occupies two out of three SDR's at max bandwidth, on the same center frequency on both for hours on end every day... Does that justify as "abuse"? Asking for a frien

Hello all. I finally have some time to work on this today, but short. I'll be unavailable starting tomorrow for a few weeks. I tried starting the server and it starts, but I get the "on-air status: un

I run the 590sg with omnirig. CW Skimmer tracks. I have setup the IQ VAC cable from the SDR Console to the CW SKimmer... but I'm not seeing CW signals. There is little documentation but plenty of blov

As FT-710 and IC-9700 are "SDR's" will it be possible to interface them to SDR-Console or is it easier to output from the IF of the rigs to an external SDR to see a true display TIA Simon what we've g

Hi All, To get the latest kit which should resolve the panning / dragging problem: Start version 1.3.5 Wait a minute or two, an Update Available option should be displayed in the Ribbon Bar, Home, Onl

Simon's World Map 1.3.5; bugfixes and some new features. https://www.g4eli.com/world-map Simon Brown https://g4eli.com https://sdr-radio.com -- - + - + - Please use https://forum.sdr-radio.com:4499/ w

Greetings, I have always wondered why attenuation settings both hardware and software or in 10db increments and not variable? is this a hardware issue or software issue? Many times, 10-30db increments

Funcube Dongle PP is detected but fails to switch on with Win 10. This is with both SDR Console and SDR Sharp. Error messages displayed by both programmes. Dongle works fine on Win 7 with both program

How do I tell what frequency the selected radio bandwidth in SDRConsole is centered at and how is it set? For example, I'm connected to an Elad S3 and if I choose the 3.072 MHz bandwidth option I can

Hi, Based on what I've found on the forum, I think the answer to this question is no but I'd like to be sure: [SDR console (v3.1 build 2572), Airspy HF+ Discovery, ELAD TM-2 VFO knob] It is possible i

Right in the middle of the CW portion and digital section of the band. Anyone with rotating beam get a DF on it. I have a Force 12 C3 pointing South (left hand side) and an inverted Vee 10 miles away

I have the above controller which I have adapted for use in Thetis with my Anan & now Hermes Lite. I am sharing the controller between two pc's and using sdr console with my IC7300 but I cannot seem t