|
Hello OM`s,
my configuration for QO-100 is : SDRConsole V3.1, IC-705, RSRP1a
V3 and transverter from LZ5HP.
I have some problems with the interfaces also my com ports. My
IC-705 is correctly connected via two com ports (CI-V is com 9 )
to my PC.
When WSJT-X for FT8 is running via cat and com 9 with my IC-705,
it is all right and works fine.
Now I start SDRC still without external radio.
The SDRC is still not running now, but it is enough my WSJT-X
interface to kill.
WSJT-X responds with this error message and stops working.
Why does kill SDRC this interface (at my com port 9) ?
At this time is nothing else happening with my PC.
In addition, I have a problem with External radio. SDRC can not
connect my IC-705.
Is the cause here a common one ?
Does anyone know this problem and can help me, especially Simon ?
Do I maybe need a virtual port ?
Vy 73 !
de Peter DL9AJ
|
|
|
Hello Peter,
My set up for QO-100 is very much like yours,
SDRConsole, RSPDuo, FT991, SG Labs Xvtr and Logging Programme Logger 32.
What logging programme are you using?
I have seen your error many times and it is always due to Com Port errors. i.e the wrong ones selected in SDRC or Omni rig and or my logging programme!!
Yes you do need a virtual comport for that config.
My setup has a virtual Comport between Logger 32 and SDRC this enables the reading of the down link frequency as shown in SDRC.
The FT991 comport (Hard USB Comport) is configured in WSJTDX (although I use JTDX)
Logger32 has functionality to control all the requirements for FT8 and SSB/CW.
Let me know what you logging programme is and I might be able to help further.
73
Ian G4GIR
toggle quoted message
Show quoted text
----- Original Message -----
Sent: 03/02/2023 09:06:26
Subject: [SDR-Radio] Problem with com interfaces
Hello OM`s,
my configuration for QO-100 is : SDRConsole V3.1, IC-705, RSRP1a V3 and transverter from LZ5HP.
I have some problems with the interfaces also my com ports. My IC-705 is correctly connected via two com ports (CI-V is com 9 ) to my PC.
When WSJT-X for FT8 is running via cat and com 9 with my IC-705, it is all right and works fine.
Now I start SDRC still without external radio.
The SDRC is still not running now, but it is enough my WSJT-X interface to kill.
WSJT-X responds with this error message and stops working.
Why does kill SDRC this interface (at my com port 9) ?
At this time is nothing else happening with my PC.
In addition, I have a problem with External radio. SDRC can not connect my IC-705.
Is the cause here a common one ?
Does anyone know this problem and can help me, especially Simon ?
Do I maybe need a virtual port ?
Vy 73 !
de Peter DL9AJ
|
|
|
Basically you don't that I can see. Nothing mentions the beast
sending samples out over an external connection. So "why bother?"
That aside, do you have COM0COM setup and configured? (Looks like
this - the COM4/COM3 setting not the CNCA0/CNCB0 setting. That is
important.)
Then you connect SDRConsole to one port and OmniRig to the other.
The rig side of OmniRig should connect to the radio's CIV. Pray
that OmniRig has a setting for the IC-705, select it, and go. Read
the files up on SDR-Radio.com for further information about
working with an external radio. Methinks a boatload of reading
will be required to develop a configuration that is going to work.
It's definitely going to be unusual and a one-off configuration as
the usual satellite configuration uses frequencies the IC-705
cannot touch.
{^_^}
On 20230203 01:06:26, Peter Dudzinski
wrote:
toggle quoted message
Show quoted text
Hello OM`s,
my configuration for QO-100 is : SDRConsole V3.1, IC-705,
RSRP1a V3 and transverter from LZ5HP.
I have some problems with the interfaces also my com ports. My
IC-705 is correctly connected via two com ports (CI-V is com 9 )
to my PC.
When WSJT-X for FT8 is running via cat and com 9 with my
IC-705, it is all right and works fine.
Now I start SDRC still without external radio.
The SDRC is still not running now, but it is enough my WSJT-X
interface to kill.
WSJT-X responds with this error message and stops working.
Why does kill SDRC this interface (at my com port 9) ?
At this time is nothing else happening with my PC.
In addition, I have a problem with External radio. SDRC can not
connect my IC-705.
Is the cause here a common one ?
Does anyone know this problem and can help me, especially Simon
?
Do I maybe need a virtual port ?
Vy 73 !
de Peter DL9AJ
|
|
|
Hi jdow and Ian
and thank you for the prompt reply.
I can´t imagine a configuration problem, because the WSJT-X works
properly without SDRC and with e. g WEB SDR.
Means for me configuration is correct. Problem appears when I
start SDRC. SDRC displayces the Application WSJT-X from com9. Why
?
It would be nice, if Simon could say something about that.
I show below my Device Manager :
As you can see my RSP1a receiver has own driver and does not need
which com port.
Via this interface communicates SDRC with my receiver.
My IC-705 needs two com ports 8 and 9.
Actually clear configuration and theoretically no conflict. Do I
need a virtual port additionally ? For what reason ?
So far I haven`t needed it. Of course, I can try it out, if I see
a clear reason.
Can someone tell me the reason exactly for my case.
That`s just my theory doesn`t have to 100% correct. I like learn
something new from you.
Something else for IAN. I don`t use a external logger, only
WSJT-X
Vy 73 !
de Peter DL9AJ
Am 03.02.2023 um 20:47 schrieb jdow:
toggle quoted message
Show quoted text
Basically you don't that I can see. Nothing mentions the beast
sending samples out over an external connection. So "why
bother?"
That aside, do you have COM0COM setup and configured? (Looks
like this - the COM4/COM3 setting not the CNCA0/CNCB0 setting.
That is important.)
Then you connect SDRConsole to one port and OmniRig to the
other. The rig side of OmniRig should connect to the radio's
CIV. Pray that OmniRig has a setting for the IC-705, select it,
and go. Read the files up on SDR-Radio.com for further
information about working with an external radio. Methinks a
boatload of reading will be required to develop a configuration
that is going to work. It's definitely going to be unusual and a
one-off configuration as the usual satellite configuration uses
frequencies the IC-705 cannot touch.
{^_^}
On 20230203 01:06:26, Peter Dudzinski
wrote:
Hello OM`s,
my configuration for QO-100 is : SDRConsole V3.1, IC-705,
RSRP1a V3 and transverter from LZ5HP.
I have some problems with the interfaces also my com ports.
My IC-705 is correctly connected via two com ports (CI-V is
com 9 ) to my PC.
When WSJT-X for FT8 is running via cat and com 9 with my
IC-705, it is all right and works fine.
Now I start SDRC still without external radio.
The SDRC is still not running now, but it is enough my WSJT-X
interface to kill.
WSJT-X responds with this error message and stops working.
Why does kill SDRC this interface (at my com port 9) ?
At this time is nothing else happening with my PC.
In addition, I have a problem with External radio. SDRC can
not connect my IC-705.
Is the cause here a common one ?
Does anyone know this problem and can help me, especially
Simon ?
Do I maybe need a virtual port ?
Vy 73 !
de Peter DL9AJ
|
|
|
If you use wsjtx with rig alone the soft controls frequency (and ptt) via cat. If you start sdr console it also looks for the comport to control the rig.. And then there maybe is logbook.. Clustersoft... So you either have to change your config each time depending what you plan to do.. Or add some virtual port where you can use one as a splitter between the different software calling for a comport. Now clear? Dg9bfc sigi Am 03.02.2023 22:19 schrieb Peter Dudzinski <dl9aj@...>:
Hi jdow and Ian
and thank you for the prompt reply.
I can´t imagine a configuration problem, because the WSJT-X works
properly without SDRC and with e. g WEB SDR.
Means for me configuration is correct. Problem appears when I
start SDRC. SDRC displayces the Application WSJT-X from com9. Why
?
It would be nice, if Simon could say something about that.
I show below my Device Manager :
As you can see my RSP1a receiver has own driver and does not need
which com port.
Via this interface communicates SDRC with my receiver.
My IC-705 needs two com ports 8 and 9.
Actually clear configuration and theoretically no conflict. Do I
need a virtual port additionally ? For what reason ?
So far I haven`t needed it. Of course, I can try it out, if I see
a clear reason.
Can someone tell me the reason exactly for my case.
That`s just my theory doesn`t have to 100% correct. I like learn
something new from you.
Something else for IAN. I don`t use a external logger, only
WSJT-X
Vy 73 !
de Peter DL9AJ
Am 03.02.2023 um 20:47 schrieb jdow:
Basically you don't that I can see. Nothing mentions the beast
sending samples out over an external connection. So "why
bother?"
That aside, do you have COM0COM setup and configured? (Looks
like this - the COM4/COM3 setting not the CNCA0/CNCB0 setting.
That is important.)
Then you connect SDRConsole to one port and OmniRig to the
other. The rig side of OmniRig should connect to the radio's
CIV. Pray that OmniRig has a setting for the IC-705, select it,
and go. Read the files up on SDR-Radio.com for further
information about working with an external radio. Methinks a
boatload of reading will be required to develop a configuration
that is going to work. It's definitely going to be unusual and a
one-off configuration as the usual satellite configuration uses
frequencies the IC-705 cannot touch.
{^_^}
On 20230203 01:06:26, Peter Dudzinski
wrote:
Hello OM`s,
my configuration for QO-100 is : SDRConsole V3.1, IC-705,
RSRP1a V3 and transverter from LZ5HP.
I have some problems with the interfaces also my com ports.
My IC-705 is correctly connected via two com ports (CI-V is
com 9 ) to my PC.
When WSJT-X for FT8 is running via cat and com 9 with my
IC-705, it is all right and works fine.
Now I start SDRC still without external radio.
The SDRC is still not running now, but it is enough my WSJT-X
interface to kill.
WSJT-X responds with this error message and stops working.
Why does kill SDRC this interface (at my com port 9) ?
At this time is nothing else happening with my PC.
In addition, I have a problem with External radio. SDRC can
not connect my IC-705.
Is the cause here a common one ?
Does anyone know this problem and can help me, especially
Simon ?
Do I maybe need a virtual port ?
Vy 73 !
de Peter DL9AJ
|
|
|
Please excuse me if you've already done this; but, after a look
at the IC-705 manuals I suspect you may need to do a deep dive
into all three IC-705 manuals and the SDR-Radio.com help files.
(Follow the menus.) SDRC will not directly drive anything other
than (some?) Kenwood radios. So you will absolutely require
OmniRig to provide the translation. What translation OmniRig can
provide for the IC-705 is in question. Since I don't have one nor
do I even know anybody other than you who does I can't help
further.
{o.o}
On 20230203 13:19:46, Peter Dudzinski
wrote:
toggle quoted message
Show quoted text
Hi jdow and Ian
and thank you for the prompt reply.
I can´t imagine a configuration problem, because the WSJT-X
works properly without SDRC and with e. g WEB SDR.
Means for me configuration is correct. Problem appears when I
start SDRC. SDRC displayces the Application WSJT-X from com9.
Why ?
It would be nice, if Simon could say something about that.
I show below my Device Manager :
As you can see my RSP1a receiver has own driver and does not
need which com port.
Via this interface communicates SDRC with my receiver.
My IC-705 needs two com ports 8 and 9.
Actually clear configuration and theoretically no conflict. Do
I need a virtual port additionally ? For what reason ?
So far I haven`t needed it. Of course, I can try it out, if I
see a clear reason.
Can someone tell me the reason exactly for my case.
That`s just my theory doesn`t have to 100% correct. I like
learn something new from you.
Something else for IAN. I don`t use a external logger, only
WSJT-X
Vy 73 !
de Peter DL9AJ
Am 03.02.2023 um 20:47 schrieb jdow:
Basically you don't that I can see. Nothing mentions the
beast sending samples out over an external connection. So "why
bother?"
That aside, do you have COM0COM setup and configured? (Looks
like this - the COM4/COM3 setting not the CNCA0/CNCB0 setting.
That is important.)
Then you connect SDRConsole to one port and OmniRig to the
other. The rig side of OmniRig should connect to the radio's
CIV. Pray that OmniRig has a setting for the IC-705, select
it, and go. Read the files up on SDR-Radio.com for further
information about working with an external radio. Methinks a
boatload of reading will be required to develop a
configuration that is going to work. It's definitely going to
be unusual and a one-off configuration as the usual satellite
configuration uses frequencies the IC-705 cannot touch.
{^_^}
On 20230203 01:06:26, Peter
Dudzinski wrote:
Hello OM`s,
my configuration for QO-100 is : SDRConsole V3.1, IC-705,
RSRP1a V3 and transverter from LZ5HP.
I have some problems with the interfaces also my com ports.
My IC-705 is correctly connected via two com ports (CI-V is
com 9 ) to my PC.
When WSJT-X for FT8 is running via cat and com 9 with my
IC-705, it is all right and works fine.
Now I start SDRC still without external radio.
The SDRC is still not running now, but it is enough my
WSJT-X interface to kill.
WSJT-X responds with this error message and stops working.
Why does kill SDRC this interface (at my com port 9) ?
At this time is nothing else happening with my PC.
In addition, I have a problem with External radio. SDRC can
not connect my IC-705.
Is the cause here a common one ?
Does anyone know this problem and can help me, especially
Simon ?
Do I maybe need a virtual port ?
Vy 73 !
de Peter DL9AJ
|
|
|
Hello Peter
Thanks' for letting me know you are only using WSJTX as the logger.
I will try and set my configuration as yours is without using my logger programme.
Will let you know how I get on.
73
Ian G4GIR
toggle quoted message
Show quoted text
----- Original Message -----
Sent: 03/02/2023 21:19:46
Subject: Re: [SDR-Radio] Problem with com interfaces
Hi jdow and Ian
and thank you for the prompt reply.
I can´t imagine a configuration problem, because the WSJT-X works properly without SDRC and with e. g WEB SDR.
Means for me configuration is correct. Problem appears when I start SDRC. SDRC displayces the Application WSJT-X from com9. Why ?
It would be nice, if Simon could say something about that.
I show below my Device Manager :
As you can see my RSP1a receiver has own driver and does not need which com port.
Via this interface communicates SDRC with my receiver.
My IC-705 needs two com ports 8 and 9.
Actually clear configuration and theoretically no conflict. Do I need a virtual port additionally ? For what reason ?
So far I haven`t needed it. Of course, I can try it out, if I see a clear reason.
Can someone tell me the reason exactly for my case.
That`s just my theory doesn`t have to 100% correct. I like learn something new from you.
Something else for IAN. I don`t use a external logger, only WSJT-X
Vy 73 !
de Peter DL9AJ
Am 03.02.2023 um 20:47 schrieb jdow:
Basically you don't that I can see. Nothing mentions the beast sending samples out over an external connection. So "why bother?"
That aside, do you have COM0COM setup and configured? (Looks like this - the COM4/COM3 setting not the CNCA0/CNCB0 setting. That is important.)
Then you connect SDRConsole to one port and OmniRig to the other. The rig side of OmniRig should connect to the radio's CIV. Pray that OmniRig has a setting for the IC-705, select it, and go. Read the files up on SDR-Radio.com for further information about working with an external radio. Methinks a boatload of reading will be required to develop a configuration that is going to work. It's definitely going to be unusual and a one-off configuration as the usual satellite configuration uses frequencies the IC-705 cannot touch.
{^_^}
On 20230203 01:06:26, Peter Dudzinski wrote:
Hello OM`s,
my configuration for QO-100 is : SDRConsole V3.1, IC-705, RSRP1a V3 and transverter from LZ5HP.
I have some problems with the interfaces also my com ports. My IC-705 is correctly connected via two com ports (CI-V is com 9 ) to my PC.
When WSJT-X for FT8 is running via cat and com 9 with my IC-705, it is all right and works fine.
Now I start SDRC still without external radio.
The SDRC is still not running now, but it is enough my WSJT-X interface to kill.
WSJT-X responds with this error message and stops working.
Why does kill SDRC this interface (at my com port 9) ?
At this time is nothing else happening with my PC.
In addition, I have a problem with External radio. SDRC can not connect my IC-705.
Is the cause here a common one ?
Does anyone know this problem and can help me, especially Simon ?
Do I maybe need a virtual port ?
Vy 73 !
de Peter DL9AJ
|
|
|
You cannot connect two programs to the same com port if running the two programs at the same time.
--
Thanks Steve M0ZEH
|
|
|
Hi Sigi,
thank you for your explation. I paste my answers below in bold.
Br Peter
Am 03.02.2023 um 22:36 schrieb
Siegfried Jackstien:
If you use wsjtx with rig alone the soft
controls frequency (and ptt) via cat.
yes, this is my case now
If you start sdr console it also looks for
the comport to control the rig..
there is no compelling reason in my case. The communication
between SDRC and RSP1a takes place via RSP1a own driver (see
below my device manager)
I suspect that it is programmed other, but i don`t know. Only
Simon knows that.
Normally, for this case the SDRC doesn`t need to know my
comports.
I think, that happens first, when we activate External Radio
by SDRC. By the way, that doesn`r work at me either with IC-705.
Common cause ?
And then there maybe is logbook..
Clustersoft...
That`s clear. Multiple access to the comports is the main
reason for this solution. If I don`t get another explanation,
I`ll try it.
It is also better for the future and other applications.
So you either have to change your config
each time depending what you plan to do.. Or add some
virtual port where you can use one as a splitter between
the different software calling for a comport. Now clear?
That`s also clear.
Am 03.02.2023 22:19 schrieb Peter
Dudzinski <dl9aj@...>:
Hi jdow and Ian
and thank you for the prompt reply.
I can´t imagine a configuration problem, because
the WSJT-X works properly without SDRC and with e.
g WEB SDR.
Means for me configuration is correct. Problem
appears when I start SDRC. SDRC displayces the
Application WSJT-X from com9. Why ?
It would be nice, if Simon could say something
about that.
I show below my Device Manager :
As you can see my RSP1a receiver has own driver
and does not need which com port.
Via this interface communicates SDRC with my
receiver.
My IC-705 needs two com ports 8 and 9.
Actually clear configuration and theoretically no
conflict. Do I need a virtual port additionally ?
For what reason ?
So far I haven`t needed it. Of course, I can try
it out, if I see a clear reason.
Can someone tell me the reason exactly for my
case.
That`s just my theory doesn`t have to 100%
correct. I like learn something new from you.
Something else for IAN. I don`t use a external
logger, only WSJT-X
Vy 73 !
de Peter DL9AJ
Am 03.02.2023 um 20:47 schrieb jdow:
Basically you don't that I can see. Nothing
mentions the beast sending samples out over an
external connection. So "why bother?"
That aside, do you have COM0COM setup and
configured? (Looks like this - the COM4/COM3
setting not the CNCA0/CNCB0 setting. That is
important.)
Then you connect SDRConsole to one port and
OmniRig to the other. The rig side of OmniRig
should connect to the radio's CIV. Pray that
OmniRig has a setting for the IC-705, select it,
and go. Read the files up on SDR-Radio.com for
further information about working with an
external radio. Methinks a boatload of reading
will be required to develop a configuration that
is going to work. It's definitely going to be
unusual and a one-off configuration as the usual
satellite configuration uses frequencies the
IC-705 cannot touch.
{^_^}
On 20230203 01:06:26, Peter Dudzinski wrote:
Hello OM`s,
my configuration for QO-100 is : SDRConsole
V3.1, IC-705, RSRP1a V3 and transverter from
LZ5HP.
I have some problems with the interfaces also
my com ports. My IC-705 is correctly connected
via two com ports (CI-V is com 9 ) to my PC.
When WSJT-X for FT8 is running via cat and
com 9 with my IC-705, it is all right and
works fine.
Now I start SDRC still without external
radio.
The SDRC is still not running now, but it is
enough my WSJT-X interface to kill.
WSJT-X responds with this error message and
stops working.
Why does kill SDRC this interface (at my com
port 9) ?
At this time is nothing else happening with
my PC.
In addition, I have a problem with External
radio. SDRC can not connect my IC-705.
Is the cause here a common one ?
Does anyone know this problem and can help
me, especially Simon ?
Do I maybe need a virtual port ?
Vy 73 !
de Peter DL9AJ
|
|
|
I believe the usual suspects, COM0COM and the like, all have
facilities for sharing com ports. But it can be tricky to setup.
I've not done it in enough years I can't help configuring that
arrangement; but, it can be done if you are careful about it.
{o.o}
On 20230204 01:04:03, Radioman ZeroZero
wrote:
toggle quoted message
Show quoted text
You cannot connect two programs to the same com port if running
the two programs at the same time.
--
Thanks Steve M0ZEH
|
|
|
On 05/02/2023 09:06, jdow wrote: I believe the usual suspects, COM0COM and the like, all have facilities for sharing com ports. Joanne, Yes, I see for com0com it is a separate download hub4com from the same site. As you say the initial setup looks tricky for some, I'm not sure, have not tried. But to save money, looks worth an attempt. 73 Alan
|
|
|
Hi to all,
thanks for the factual discussion Ian and Alan. Ian you wrote so many facts and questions. I will answer everything after trying something myself, especially VSP-Manager.
First we have similar problems. There are currently two important questions for me:
1. Do we absolutely need a virtual port for SDRC to work with WSJT-X ?
2. if yes, do we also need the split function to share the resources ? Tools like com0com and VSP-Manager don`t support it. That do e. g VSP-Emulator.
What we need ? I am not 100% sure, if correct.
Alan wrote, that hub4com is additionally needed. Is there anyone, who has a working configuration ?
i will try it, but would make some steps easier here.
Vy 73 !
Peter DL9AJ
Am 05.02.2023 um 11:46 schrieb Alan G4ZFQ:
toggle quoted message
Show quoted text
On 05/02/2023 09:06, jdow wrote:
I believe the usual suspects, COM0COM and the like, all have facilities for sharing com ports.
Joanne,
Yes, I see for com0com it is a separate download hub4com from the same site.
As you say the initial setup looks tricky for some, I'm not sure, have not tried. But to save money, looks worth an attempt.
73 Alan
|
|
|
Hi Peter,
no, you do not need a com-port for SDRC to work with WSJT-X.
Kind regards
Matthias
www.dd1us.de
-----Ursprüngliche Nachricht-----
Von: main@SDR-Radio.groups.io <main@SDR-Radio.groups.io> Im Auftrag von Peter Dudzinski via groups.io
Gesendet: Sonntag, 5. Februar 2023 17:39
An: main@SDR-Radio.groups.io
Betreff: Re: [SDR-Radio] Problem with com interfaces
Hi to all,
thanks for the factual discussion Ian and Alan. Ian you wrote so many facts and questions. I will answer everything after trying something myself, especially VSP-Manager.
First we have similar problems. There are currently two important questions for me:
1. Do we absolutely need a virtual port for SDRC to work with WSJT-X ?
2. if yes, do we also need the split function to share the resources ?
Tools like com0com and VSP-Manager don`t support it. That do e. g VSP-Emulator.
What we need ? I am not 100% sure, if correct.
Alan wrote, that hub4com is additionally needed. Is there anyone, who has a working configuration ?
i will try it, but would make some steps easier here.
Vy 73 !
Peter DL9AJ
Am 05.02.2023 um 11:46 schrieb Alan G4ZFQ:
toggle quoted message
Show quoted text
On 05/02/2023 09:06, jdow wrote:
I believe the usual suspects, COM0COM and the like, all have facilities for sharing com ports.
Joanne,
Yes, I see for com0com it is a separate download hub4com from the same
site.
As you say the initial setup looks tricky for some, I'm not sure, have
not tried. But to save money, looks worth an attempt.
73 Alan
|
|
|
Hi Matthius
How do you otherwise connect the rig control capabilities of WSJT-X to SDRC? I've always done it with virtual comports.
73
Charlie DL3WDG
Hi Peter,
no, you do not need a com-port for SDRC to work with WSJT-X.
Kind regards
Matthias
www.dd1us.de
-----Ursprüngliche Nachricht-----
Von: main@SDR-Radio.groups.io <main@SDR-Radio.groups.io> Im Auftrag von Peter Dudzinski via groups.io
Gesendet: Sonntag, 5. Februar 2023 17:39
An: main@SDR-Radio.groups.io
Betreff: Re: [SDR-Radio] Problem with com interfaces
Hi to all,
thanks for the factual discussion Ian and Alan. Ian you wrote so many facts and questions. I will answer everything after trying something myself, especially VSP-Manager.
First we have similar problems. There are currently two important questions for me:
1. Do we absolutely need a virtual port for SDRC to work with WSJT-X ?
2. if yes, do we also need the split function to share the resources ?
Tools like com0com and VSP-Manager don`t support it. That do e. g VSP-Emulator.
What we need ? I am not 100% sure, if correct.
Alan wrote, that hub4com is additionally needed. Is there anyone, who has a working configuration ?
i will try it, but would make some steps easier here.
Vy 73 !
Peter DL9AJ
Am 05.02.2023 um 11:46 schrieb Alan G4ZFQ:
> On 05/02/2023 09:06, jdow wrote:
> > I believe the usual suspects, COM0COM and the like, all have
> facilities for sharing com ports.
>
> Joanne,
>
> Yes, I see for com0com it is a separate download hub4com from the same
> site.
>
> As you say the initial setup looks tricky for some, I'm not sure, have
> not tried. But to save money, looks worth an attempt.
>
> 73 Alan
>
>
>
>
>
|
|
|
Matt.. He uses sdrc with a rig. Sdrc wants a cat port.. And wsjtx wants a cat port. I would forward the real comport to a virtual port and set that virtual port as splitter. Dg9bfc sigi
Hi Peter,
no, you do not need a com-port for SDRC to work with WSJT-X.
Kind regards
Matthias
www.dd1us.de
-----Ursprüngliche Nachricht-----
Von: main@SDR-Radio.groups.io <main@SDR-Radio.groups.io> Im Auftrag von Peter Dudzinski via groups.io
Gesendet: Sonntag, 5. Februar 2023 17:39
An: main@SDR-Radio.groups.io
Betreff: Re: [SDR-Radio] Problem with com interfaces
Hi to all,
thanks for the factual discussion Ian and Alan. Ian you wrote so many facts and questions. I will answer everything after trying something myself, especially VSP-Manager.
First we have similar problems. There are currently two important questions for me:
1. Do we absolutely need a virtual port for SDRC to work with WSJT-X ?
2. if yes, do we also need the split function to share the resources ?
Tools like com0com and VSP-Manager don`t support it. That do e. g VSP-Emulator.
What we need ? I am not 100% sure, if correct.
Alan wrote, that hub4com is additionally needed. Is there anyone, who has a working configuration ?
i will try it, but would make some steps easier here.
Vy 73 !
Peter DL9AJ
Am 05.02.2023 um 11:46 schrieb Alan G4ZFQ:
> On 05/02/2023 09:06, jdow wrote:
> > I believe the usual suspects, COM0COM and the like, all have
> facilities for sharing com ports.
>
> Joanne,
>
> Yes, I see for com0com it is a separate download hub4com from the same
> site.
>
> As you say the initial setup looks tricky for some, I'm not sure, have
> not tried. But to save money, looks worth an attempt.
>
> 73 Alan
>
>
>
>
>
|
|
|
Hi Mathias,
my problem is, that a working WSJ-T is interrupted when I turn on SDRC.
I use RSP1a as receiver and this is via own driver connected to SDRC (without com interface).
Actuelly no reason to break the com interface.
Vy 73
Peter
Am 05.02.2023 um 18:05 schrieb Matthias Bopp:
toggle quoted message
Show quoted text
Hi Peter,
no, you do not need a com-port for SDRC to work with WSJT-X.
Kind regards
Matthias
www.dd1us.de
-----Ursprüngliche Nachricht-----
Von: main@SDR-Radio.groups.io <main@SDR-Radio.groups.io> Im Auftrag von Peter Dudzinski via groups.io
Gesendet: Sonntag, 5. Februar 2023 17:39
An: main@SDR-Radio.groups.io
Betreff: Re: [SDR-Radio] Problem with com interfaces
Hi to all,
thanks for the factual discussion Ian and Alan. Ian you wrote so many facts and questions. I will answer everything after trying something myself, especially VSP-Manager.
First we have similar problems. There are currently two important questions for me:
1. Do we absolutely need a virtual port for SDRC to work with WSJT-X ?
2. if yes, do we also need the split function to share the resources ?
Tools like com0com and VSP-Manager don`t support it. That do e. g VSP-Emulator.
What we need ? I am not 100% sure, if correct.
Alan wrote, that hub4com is additionally needed. Is there anyone, who has a working configuration ?
i will try it, but would make some steps easier here.
Vy 73 !
Peter DL9AJ
Am 05.02.2023 um 11:46 schrieb Alan G4ZFQ:
On 05/02/2023 09:06, jdow wrote:
I believe the usual suspects, COM0COM and the like, all have facilities for sharing com ports.
Joanne,
Yes, I see for com0com it is a separate download hub4com from the same
site.
As you say the initial setup looks tricky for some, I'm not sure, have
not tried. But to save money, looks worth an attempt.
73 Alan
|
|
|
Hi Carlie,
Sorry I had missen that you are using an normal Radio. I am using a SDR.
Kind regards
Matthias
-------- Ursprüngliche Nachricht --------
Von: Charles Suckling <g3wdg1@...>
Datum: 05.02.23 18:12 (GMT+01:00)
An: main@sdr-radio.groups.io
Betreff: Re: [SDR-Radio] Problem with com interfaces
Hi Matthius
How do you otherwise connect the rig control capabilities of WSJT-X to SDRC? I've always done it with virtual comports.
73
Charlie DL3WDG
Hi Peter,
no, you do not need a com-port for SDRC to work with WSJT-X.
Kind regards
Matthias
www.dd1us.de
-----Ursprüngliche Nachricht-----
Von: main@SDR-Radio.groups.io <main@SDR-Radio.groups.io> Im Auftrag von Peter Dudzinski via
groups.io
Gesendet: Sonntag, 5. Februar 2023 17:39
An: main@SDR-Radio.groups.io
Betreff: Re: [SDR-Radio] Problem with com interfaces
Hi to all,
thanks for the factual discussion Ian and Alan. Ian you wrote so many facts and questions. I will answer everything after trying something myself, especially VSP-Manager.
First we have similar problems. There are currently two important questions for me:
1. Do we absolutely need a virtual port for SDRC to work with WSJT-X ?
2. if yes, do we also need the split function to share the resources ?
Tools like com0com and VSP-Manager don`t support it. That do e. g VSP-Emulator.
What we need ? I am not 100% sure, if correct.
Alan wrote, that hub4com is additionally needed. Is there anyone, who has a working configuration ?
i will try it, but would make some steps easier here.
Vy 73 !
Peter DL9AJ
Am 05.02.2023 um 11:46 schrieb Alan G4ZFQ:
> On 05/02/2023 09:06, jdow wrote:
> > I believe the usual suspects, COM0COM and the like, all have
> facilities for sharing com ports.
>
> Joanne,
>
> Yes, I see for com0com it is a separate download hub4com from the same
> site.
>
> As you say the initial setup looks tricky for some, I'm not sure, have
> not tried. But to save money, looks worth an attempt.
>
> 73 Alan
>
>
>
>
>
|
|
|
Hi Peter
I have exactly the same setup here. RSP1A connected to SDRC via the normal drivers.
To tune the frequency of the RSP1A from WSJT-X I connect WSJT-X to SDRC using virtual com ports as created by com0com. WSJT-X should be set to use radio TS-2000. WSJT-X can then tune the RSP1A, via SDRC.
73
Charlie DL3WDG
On Sun, 5 Feb 2023 at 18:23, Peter Dudzinski < dl9aj@...> wrote: Hi Mathias,
my problem is, that a working WSJ-T is interrupted when I turn on SDRC.
I use RSP1a as receiver and this is via own driver connected to SDRC
(without com interface).
Actuelly no reason to break the com interface.
Vy 73
Peter
Am 05.02.2023 um 18:05 schrieb Matthias Bopp:
> Hi Peter,
>
> no, you do not need a com-port for SDRC to work with WSJT-X.
>
> Kind regards
>
> Matthias
>
> www.dd1us.de
>
>
> -----Ursprüngliche Nachricht-----
> Von: main@SDR-Radio.groups.io <main@SDR-Radio.groups.io> Im Auftrag von Peter Dudzinski via groups.io
> Gesendet: Sonntag, 5. Februar 2023 17:39
> An: main@SDR-Radio.groups.io
> Betreff: Re: [SDR-Radio] Problem with com interfaces
>
> Hi to all,
>
> thanks for the factual discussion Ian and Alan. Ian you wrote so many facts and questions. I will answer everything after trying something myself, especially VSP-Manager.
>
> First we have similar problems. There are currently two important questions for me:
>
> 1. Do we absolutely need a virtual port for SDRC to work with WSJT-X ?
>
> 2. if yes, do we also need the split function to share the resources ?
> Tools like com0com and VSP-Manager don`t support it. That do e. g VSP-Emulator.
>
> What we need ? I am not 100% sure, if correct.
>
> Alan wrote, that hub4com is additionally needed. Is there anyone, who has a working configuration ?
>
> i will try it, but would make some steps easier here.
>
> Vy 73 !
>
> Peter DL9AJ
>
>
> Am 05.02.2023 um 11:46 schrieb Alan G4ZFQ:
>> On 05/02/2023 09:06, jdow wrote:
>>> I believe the usual suspects, COM0COM and the like, all have
>> facilities for sharing com ports.
>>
>> Joanne,
>>
>> Yes, I see for com0com it is a separate download hub4com from the same
>> site.
>>
>> As you say the initial setup looks tricky for some, I'm not sure, have
>> not tried. But to save money, looks worth an attempt.
>>
>> 73 Alan
>>
>>
>>
>>
>>
>
>
>
>
>
>
>
>
>
|
|
|
Hi Charlie,
thanks for the Info. It is not all clear.
What does mean "normal driver" ? Is this the supplied driver for
RSP1 ?
If yes, then is this driver displayed separately at device
manager and not at comports. Is that your case ?
Then you choose in the SDRC menu SDRPlay V3.
Do you send e. g. FT8 via TS-2000 ? If yes, how does happen , if
your WSJT-X is connected to SDRC.
But in the next sentence you write "WSJT-X should be set to use
radio TS-2000"
I think, few screenshots about your configuration (WSJT-X and
com0com) would be helpful.
Tune is for me a later topic. First it has to work at all.
Do you use External Radio function for your TS-2000 at SDRC ?
Vy 73 !
Peter DL9AJ
Am 05.02.2023 um 18:32 schrieb Charles
Suckling:
toggle quoted message
Show quoted text
Hi Peter
I have exactly the same
setup here. RSP1A connected to SDRC via the normal drivers.
To tune the frequency of the
RSP1A from WSJT-X I connect WSJT-X to SDRC using virtual com
ports as created by com0com. WSJT-X should be set to use
radio TS-2000. WSJT-X can then tune the RSP1A, via SDRC.
73
Charlie DL3WDG
On Sun, 5 Feb 2023 at 18:23,
Peter Dudzinski < dl9aj@...>
wrote:
Hi
Mathias,
my problem is, that a working WSJ-T is interrupted when I turn
on SDRC.
I use RSP1a as receiver and this is via own driver connected
to SDRC
(without com interface).
Actuelly no reason to break the com interface.
Vy 73
Peter
Am 05.02.2023 um 18:05 schrieb Matthias Bopp:
> Hi Peter,
>
> no, you do not need a com-port for SDRC to work with
WSJT-X.
>
> Kind regards
>
> Matthias
>
> www.dd1us.de
>
>
> -----Ursprüngliche Nachricht-----
> Von: main@SDR-Radio.groups.io
<main@SDR-Radio.groups.io>
Im Auftrag von Peter Dudzinski via groups.io
> Gesendet: Sonntag, 5. Februar 2023 17:39
> An: main@SDR-Radio.groups.io
> Betreff: Re: [SDR-Radio] Problem with com interfaces
>
> Hi to all,
>
> thanks for the factual discussion Ian and Alan. Ian you
wrote so many facts and questions. I will answer everything
after trying something myself, especially VSP-Manager.
>
> First we have similar problems. There are currently two
important questions for me:
>
> 1. Do we absolutely need a virtual port for SDRC to work
with WSJT-X ?
>
> 2. if yes, do we also need the split function to share
the resources ?
> Tools like com0com and VSP-Manager don`t support it. That
do e. g VSP-Emulator.
>
> What we need ? I am not 100% sure, if correct.
>
> Alan wrote, that hub4com is additionally needed. Is
there anyone, who has a working configuration ?
>
> i will try it, but would make some steps easier here.
>
> Vy 73 !
>
> Peter DL9AJ
>
>
> Am 05.02.2023 um 11:46 schrieb Alan G4ZFQ:
>> On 05/02/2023 09:06, jdow wrote:
>>> I believe the usual suspects, COM0COM and the
like, all have
>> facilities for sharing com ports.
>>
>> Joanne,
>>
>> Yes, I see for com0com it is a separate download
hub4com from the same
>> site.
>>
>> As you say the initial setup looks tricky for some,
I'm not sure, have
>> not tried. But to save money, looks worth an attempt.
>>
>> 73 Alan
>>
>>
>>
>>
>>
>
>
>
>
>
>
>
>
>
|
|
|
He wants to also use his rig (sdr for receive trx to transmit)... Yes setting up a hybrid station for qo100 can be tricky when it comes to digi modes. Its not connecting wsjtx to sdrc... Its the problem he uses wsjtx on normal rig alone... And in combination with sdrc when on qo100.. A splitter port could solve that.. Rig is connected to a real comport Port is forwarded to a virtual port that is set as splitter., and wsjtx, sdrc, logbook, etc etc... All are then using that splitter port. No software should direct use the hardware comport. All must use splitter. That should solve it. Dg9bfc sigi
Hi Peter
I have exactly the same setup here. RSP1A connected to SDRC via the normal drivers.
To tune the frequency of the RSP1A from WSJT-X I connect WSJT-X to SDRC using virtual com ports as created by com0com. WSJT-X should be set to use radio TS-2000. WSJT-X can then tune the RSP1A, via SDRC.
73
Charlie DL3WDG
On Sun, 5 Feb 2023 at 18:23, Peter Dudzinski < dl9aj@...> wrote: Hi Mathias,
my problem is, that a working WSJ-T is interrupted when I turn on SDRC.
I use RSP1a as receiver and this is via own driver connected to SDRC
(without com interface).
Actuelly no reason to break the com interface.
Vy 73
Peter
Am 05.02.2023 um 18:05 schrieb Matthias Bopp:
> Hi Peter,
>
> no, you do not need a com-port for SDRC to work with WSJT-X.
>
> Kind regards
>
> Matthias
>
> www.dd1us.de
>
>
> -----Ursprüngliche Nachricht-----
> Von: main@SDR-Radio.groups.io <main@SDR-Radio.groups.io> Im Auftrag von Peter Dudzinski via groups.io
> Gesendet: Sonntag, 5. Februar 2023 17:39
> An: main@SDR-Radio.groups.io
> Betreff: Re: [SDR-Radio] Problem with com interfaces
>
> Hi to all,
>
> thanks for the factual discussion Ian and Alan. Ian you wrote so many facts and questions. I will answer everything after trying something myself, especially VSP-Manager.
>
> First we have similar problems. There are currently two important questions for me:
>
> 1. Do we absolutely need a virtual port for SDRC to work with WSJT-X ?
>
> 2. if yes, do we also need the split function to share the resources ?
> Tools like com0com and VSP-Manager don`t support it. That do e. g VSP-Emulator.
>
> What we need ? I am not 100% sure, if correct.
>
> Alan wrote, that hub4com is additionally needed. Is there anyone, who has a working configuration ?
>
> i will try it, but would make some steps easier here.
>
> Vy 73 !
>
> Peter DL9AJ
>
>
> Am 05.02.2023 um 11:46 schrieb Alan G4ZFQ:
>> On 05/02/2023 09:06, jdow wrote:
>>> I believe the usual suspects, COM0COM and the like, all have
>> facilities for sharing com ports.
>>
>> Joanne,
>>
>> Yes, I see for com0com it is a separate download hub4com from the same
>> site.
>>
>> As you say the initial setup looks tricky for some, I'm not sure, have
>> not tried. But to save money, looks worth an attempt.
>>
>> 73 Alan
>>
>>
>>
>>
>>
>
>
>
>
>
>
>
>
>
|
|
|
