|
Simon Brown
toggle quoted message
Show quoted text
From: main@SDR-Radio.groups.io <main@SDR-Radio.groups.io> on behalf of Everett N4CY via groups.io <everettsharp@...>
Sent: 22 November 2022 19:30
To: main@SDR-Radio.groups.io <main@SDR-Radio.groups.io>
Subject: Re: [SDR-Radio] Elad FDM-S3 with DL2EBV band filters
Simon,
This is what they sent me:
54MHz-69Mhz frequency range is not available, this is a limitation we are trying to fix quickly,- the maximum tuning frequency is 4.25GHz, with a decrease of performance from 2GHz - 2.5GHz up to 4.2GHz.
Everett
In a message dated 11/22/2022 1:19:03 PM Central Standard Time, simon@... writes:
Hi,
What's the Downconverter spec - frequency range?
From: main@SDR-Radio.groups.io <main@SDR-Radio.groups.io> on behalf of Everett N4CY via groups.io <everettsharp@...>
Sent: 22 November 2022 18:33
To: main@SDR-Radio.groups.io <main@SDR-Radio.groups.io>
Subject: Re: [SDR-Radio] Elad FDM-S3 with DL2EBV band filters
I don't know on the filter switching, as I have been tied up moving over to the new computer. I will play with them when I get a chance. I would not wait for ELAD to list the downconverters on their website . I would
send a email directly to ELAD requesting the doenconverter.
Everett
In a message dated 11/22/2022 12:06:50 PM Central Standard Time,
simon@... writes:
Was the filter switching OK? I have to send my S3 back - I've lost VHF sensitivity and will buy a downconverter when they arrive on the website.
What's the downconverter frequency range?
From: main@SDR-Radio.groups.io <main@SDR-Radio.groups.io> on behalf of Everett N4CY via groups.io <everettsharp@...>
Sent: 22 November 2022 17:42
To: main@sdr-radio.groups.io <main@sdr-radio.groups.io>
Subject: Re: [SDR-Radio] Elad FDM-S3 with DL2EBV band filters
Simon,
I have the filters in both of mine. I had to send my Downconverter back to ELAD, as the USB C broke off of the Downconverter circuit board while installing it. ELAD should Receive it today.
Everett
On Nov 22, 2022, at 11:31 AM, Simon Brown <simon@...> wrote:
I'm surprised - sounds like the commands may be sent too soon. I don't have any filters, will have to buy a set for testing. To be honest I doubt you really need them.
From: main@SDR-Radio.groups.io <main@SDR-Radio.groups.io> on behalf of Francesco Di Giovanni via groups.io <fdigio1@...>
Sent: 21 November 2022 16:24
To: main@SDR-Radio.groups.io <main@SDR-Radio.groups.io>
Subject: [SDR-Radio] Elad FDM-S3 with DL2EBV band filters
[Edited Message Follows]
Hi,
I own an Elad FDM-S3 equipped with DL2EBV band filters.
When I switch between ranges e.g. from 5MHz to e.g. LW 60kHz, it's like there is an AGC problem.
The signal level is very low and only by going to an intermediate frequency between the two and returning to the LF, the situation returns to normal.
The same in reverse.
This does not happen with Elad SW2
Any idea?
73
Francesco. IN3XZP
--
- + - + -
--
- + - + -
--
- + - + -
-- - + - + -
|
|
|
Everett N4CY
Simon,
This is what they sent me: 54MHz-69Mhz frequency range is not available, this is a limitation we are trying to fix quickly,- the maximum tuning frequency is 4.25GHz, with a decrease of performance from 2GHz - 2.5GHz up to 4.2GHz.
Everett
In a message dated 11/22/2022 1:19:03 PM Central Standard Time, simon@... writes:
Hi,
What's the Downconverter spec - frequency range?
From: main@SDR-Radio.groups.io <main@SDR-Radio.groups.io> on behalf of Everett N4CY via groups.io <everettsharp@...> Sent: 22 November 2022 18:33 To: main@SDR-Radio.groups.io <main@SDR-Radio.groups.io> Subject: Re: [SDR-Radio] Elad FDM-S3 with DL2EBV band filters
I don't know on the filter switching, as I have been tied up moving over to the new computer. I will play with them when I get a chance. I would not wait for ELAD to list the downconverters on their website . I would send a email directly to ELAD requesting the doenconverter.
Everett
In a message dated 11/22/2022 12:06:50 PM Central Standard Time, simon@... writes:
Was the filter switching OK? I have to send my S3 back - I've lost VHF sensitivity and will buy a downconverter when they arrive on the website.
What's the downconverter frequency range?
From: main@SDR-Radio.groups.io <main@SDR-Radio.groups.io> on behalf of Everett N4CY via groups.io <everettsharp@...> Sent: 22 November 2022 17:42 To: main@sdr-radio.groups.io <main@sdr-radio.groups.io> Subject: Re: [SDR-Radio] Elad FDM-S3 with DL2EBV band filters
Simon,
I have the filters in both of mine. I had to send my Downconverter back to ELAD, as the USB C broke off of the Downconverter circuit board while installing it. ELAD should Receive it today.
Everett
On Nov 22, 2022, at 11:31 AM, Simon Brown <simon@...> wrote:
I'm surprised - sounds like the commands may be sent too soon. I don't have any filters, will have to buy a set for testing. To be honest I doubt you really need them.
From: main@SDR-Radio.groups.io <main@SDR-Radio.groups.io> on behalf of Francesco Di Giovanni via groups.io <fdigio1@...> Sent: 21 November 2022 16:24 To: main@SDR-Radio.groups.io <main@SDR-Radio.groups.io> Subject: [SDR-Radio] Elad FDM-S3 with DL2EBV band filters
[Edited Message Follows]
Hi,
I own an Elad FDM-S3 equipped with DL2EBV band filters.
When I switch between ranges e.g. from 5MHz to e.g. LW 60kHz, it's like there is an AGC problem.
The signal level is very low and only by going to an intermediate frequency between the two and returning to the LF, the situation returns to normal.
The same in reverse.
This does not happen with Elad SW2
Any idea?
73
Francesco. IN3XZP
--
- + - + -
--
- + - + -
--
- + - + -
|
|
|
Simon Brown
Hi,
What's the Downconverter spec - frequency range?
toggle quoted message
Show quoted text
From: main@SDR-Radio.groups.io <main@SDR-Radio.groups.io> on behalf of Everett N4CY via groups.io <everettsharp@...>
Sent: 22 November 2022 18:33
To: main@SDR-Radio.groups.io <main@SDR-Radio.groups.io>
Subject: Re: [SDR-Radio] Elad FDM-S3 with DL2EBV band filters
I don't know on the filter switching, as I have been tied up moving over to the new computer. I will play with them when I get a chance. I would not wait for ELAD to list the downconverters on their website .
I would send a email directly to ELAD requesting the doenconverter.
Everett
In a message dated 11/22/2022 12:06:50 PM Central Standard Time, simon@... writes:
Was the filter switching OK? I have to send my S3 back - I've lost VHF sensitivity and will buy a downconverter when they arrive on the website.
What's the downconverter frequency range?
From: main@SDR-Radio.groups.io <main@SDR-Radio.groups.io> on behalf of Everett N4CY via groups.io <everettsharp@...>
Sent: 22 November 2022 17:42
To: main@sdr-radio.groups.io <main@sdr-radio.groups.io>
Subject: Re: [SDR-Radio] Elad FDM-S3 with DL2EBV band filters
Simon,
I have the filters in both of mine. I had to send my Downconverter back to ELAD, as the USB C broke off of the Downconverter circuit board while installing it. ELAD should Receive it today.
Everett
On Nov 22, 2022, at 11:31 AM, Simon Brown <simon@...> wrote:
I'm surprised - sounds like the commands may be sent too soon. I don't have any filters, will have to buy a set for testing. To be honest I doubt you really need them.
From: main@SDR-Radio.groups.io <main@SDR-Radio.groups.io> on behalf of Francesco Di Giovanni via groups.io <fdigio1@...>
Sent: 21 November 2022 16:24
To: main@SDR-Radio.groups.io <main@SDR-Radio.groups.io>
Subject: [SDR-Radio] Elad FDM-S3 with DL2EBV band filters
[Edited Message Follows]
Hi,
I own an Elad FDM-S3 equipped with DL2EBV band filters.
When I switch between ranges e.g. from 5MHz to e.g. LW 60kHz, it's like there is an AGC problem.
The signal level is very low and only by going to an intermediate frequency between the two and returning to the LF, the situation returns to normal.
The same in reverse.
This does not happen with Elad SW2
Any idea?
73
Francesco. IN3XZP
--
- + - + -
--
- + - + -
-- - + - + -
|
|
|
Everett N4CY
I don't know on the filter switching, as I have been tied up moving over to the new computer. I will play with them when I get a chance. I would not wait for ELAD to list the downconverters on their website . I would send a email directly to ELAD requesting the doenconverter.
Everett
In a message dated 11/22/2022 12:06:50 PM Central Standard Time, simon@... writes:
Was the filter switching OK? I have to send my S3 back - I've lost VHF sensitivity and will buy a downconverter when they arrive on the website.
What's the downconverter frequency range?
From: main@SDR-Radio.groups.io <main@SDR-Radio.groups.io> on behalf of Everett N4CY via groups.io <everettsharp@...> Sent: 22 November 2022 17:42 To: main@sdr-radio.groups.io <main@sdr-radio.groups.io> Subject: Re: [SDR-Radio] Elad FDM-S3 with DL2EBV band filters
Simon,
I have the filters in both of mine. I had to send my Downconverter back to ELAD, as the USB C broke off of the Downconverter circuit board while installing it. ELAD should Receive it today.
Everett
On Nov 22, 2022, at 11:31 AM, Simon Brown <simon@...> wrote:
I'm surprised - sounds like the commands may be sent too soon. I don't have any filters, will have to buy a set for testing. To be honest I doubt you really need them.
From: main@SDR-Radio.groups.io <main@SDR-Radio.groups.io> on behalf of Francesco Di Giovanni via groups.io <fdigio1@...> Sent: 21 November 2022 16:24 To: main@SDR-Radio.groups.io <main@SDR-Radio.groups.io> Subject: [SDR-Radio] Elad FDM-S3 with DL2EBV band filters
[Edited Message Follows]
Hi,
I own an Elad FDM-S3 equipped with DL2EBV band filters.
When I switch between ranges e.g. from 5MHz to e.g. LW 60kHz, it's like there is an AGC problem.
The signal level is very low and only by going to an intermediate frequency between the two and returning to the LF, the situation returns to normal.
The same in reverse.
This does not happen with Elad SW2
Any idea?
73
Francesco. IN3XZP
--
- + - + -
--
- + - + -
|
|
|
Simon Brown
Was the filter switching OK? I have to send my S3 back - I've lost VHF sensitivity and will buy a downconverter when they arrive on the website.
What's the downconverter frequency range?
toggle quoted message
Show quoted text
From: main@SDR-Radio.groups.io <main@SDR-Radio.groups.io> on behalf of Everett N4CY via groups.io <everettsharp@...>
Sent: 22 November 2022 17:42
To: main@sdr-radio.groups.io <main@sdr-radio.groups.io>
Subject: Re: [SDR-Radio] Elad FDM-S3 with DL2EBV band filters
Simon,
I have the filters in both of mine. I had to send my Downconverter back to ELAD, as the USB C broke off of the Downconverter circuit board while installing it. ELAD should Receive it today.
Everett
On Nov 22, 2022, at 11:31 AM, Simon Brown <simon@...> wrote:
I'm surprised - sounds like the commands may be sent too soon. I don't have any filters, will have to buy a set for testing. To be honest I doubt you really need them.
From: main@SDR-Radio.groups.io <main@SDR-Radio.groups.io> on behalf of Francesco Di Giovanni via groups.io <fdigio1@...>
Sent: 21 November 2022 16:24
To: main@SDR-Radio.groups.io <main@SDR-Radio.groups.io>
Subject: [SDR-Radio] Elad FDM-S3 with DL2EBV band filters
[Edited Message Follows]
Hi,
I own an Elad FDM-S3 equipped with DL2EBV band filters.
When I switch between ranges e.g. from 5MHz to e.g. LW 60kHz, it's like there is an AGC problem.
The signal level is very low and only by going to an intermediate frequency between the two and returning to the LF, the situation returns to normal.
The same in reverse.
This does not happen with Elad SW2
Any idea?
73
Francesco. IN3XZP
--
- + - + -
-- - + - + -
|
|
|
Everett N4CY
Simon,
I have the filters in both of mine. I had to send my Downconverter back to ELAD, as the USB C broke off of the Downconverter circuit board while installing it. ELAD should Receive it today.
On Nov 22, 2022, at 11:31 AM, Simon Brown <simon@...> wrote:
I'm surprised - sounds like the commands may be sent too soon. I don't have any filters, will have to buy a set for testing. To be honest I doubt you really need them.
From: main@SDR-Radio.groups.io <main@SDR-Radio.groups.io> on behalf of Francesco Di Giovanni via groups.io <fdigio1@...>
Sent: 21 November 2022 16:24
To: main@SDR-Radio.groups.io <main@SDR-Radio.groups.io>
Subject: [SDR-Radio] Elad FDM-S3 with DL2EBV band filters
[Edited Message Follows]
Hi,
I own an Elad FDM-S3 equipped with DL2EBV band filters.
When I switch between ranges e.g. from 5MHz to e.g. LW 60kHz, it's like there is an AGC problem.
The signal level is very low and only by going to an intermediate frequency between the two and returning to the LF, the situation returns to normal.
The same in reverse.
This does not happen with Elad SW2
Any idea?
73
Francesco. IN3XZP
-- - + - + -
|
|
|
Simon Brown
I'm surprised - sounds like the commands may be sent too soon. I don't have any filters, will have to buy a set for testing. To be honest I doubt you really need them.
toggle quoted message
Show quoted text
From: main@SDR-Radio.groups.io <main@SDR-Radio.groups.io> on behalf of Francesco Di Giovanni via groups.io <fdigio1@...>
Sent: 21 November 2022 16:24
To: main@SDR-Radio.groups.io <main@SDR-Radio.groups.io>
Subject: [SDR-Radio] Elad FDM-S3 with DL2EBV band filters
[Edited Message Follows]
Hi,
I own an Elad FDM-S3 equipped with DL2EBV band filters.
When I switch between ranges e.g. from 5MHz to e.g. LW 60kHz, it's like there is an AGC problem.
The signal level is very low and only by going to an intermediate frequency between the two and returning to the LF, the situation returns to normal.
The same in reverse.
This does not happen with Elad SW2
Any idea?
73
Francesco. IN3XZP
-- - + - + -
|
|
|
Hi,
I own an Elad FDM-S3 equipped with DL2EBV band filters.
When I switch between ranges e.g. from 5MHz to e.g. LW 60kHz, it's like there is an AGC problem.
The signal level is very low and only by going to an intermediate frequency between the two and returning to the LF, the situation returns to normal.
The same in reverse.
This does not happen with Elad SW2
Any idea?
73
Francesco. IN3XZP
|
|
|
