Thanks, I knew it was something simple!

#sdrconsolev3

Hi Sigi, Runs with Airspy HF+ Discovery just fine. 73, Jack

#cat #kenwood #sdrconsolev3

Hey everyone, thanks for all the replies in here, just wanted to check back in and confirm (for possible other users) that the X300 works. I have nearly no problems running the Ettus X300 via ethernet

#sdrconsolev3 #ettus

Negative, three columns is all we get. 73 Kriss KA1GJU

#sdrconsolev3

Hi, Have a RSPdx, with its 3 Ant. inputs. Just a not very important suggestion regarding Ant in-use indication: No problem with pulling up the drop-down for showing or changing the in-use Ant. Works f

#sdrconsolev3

I have some favourites set up that don't have saved receivers (for signals that are too wide for any of the SDR Console receiver options, just for seeing them on the spectrum), and the favourites mark

#bug #sdrconsolev3

Hi Simon, Problem is solved, it was actually due to an incorrectly configured RX / TX converter. Thank you very much for that incredible Software!

#adalmpluto #sdrconsolev3 #pluto

Dear OMs and YLs, since yesterday i have had a problem with pluto transmission. The transmission frequency can no longer be synchronized with the reception frequency and always remains at 10489750000

#sdrconsolev3 #sdr-consolev3 #sdrconsole #qo100 #pluto

I also struggled for a long time with a distorted microphone audio. In the end I found a solution that always works well for me (the names are based on the Dutch Windows 10 version): Go to the Configu

#sdrconsolev3 #pluto

SSB action for AM received as SSB depends on the RX filter design. Most likely you will not have a carrier present at a level suitable for driving AGC so you'd be receiving it as if it was sent SSB ev

#sdrconsolev3

Hi, If there’s a service problem it’s best to report this to SDRplay – their service should be bullet-proof. Simon Brown, G4ELI https://www.sdr-radio.com

#sdrconsolev3 #sdrplay #rsp1a #bug

i do the finetuning in the receive panel (not receiver pane but the receive dsp panel ... receive "dsp"box ... and use the if display for only ONE receiver thats good enough (and saves a bit cpu load)

#sdrconsolev3 #request

Thanks Grant for the info, I reactivated the V3 ... Thanks 73 Franco

#sdrplay #sdruno #bug #sdrconsolev3

When monitoring multiple narrow channels on a wide part of the spectrum (e.g. airband), the lines that mark the receiver's position are so close together that it's hard to see if there's a signal or i

#sdrconsolev3 #future

Eventually found the problem. I had to delete everything in the registry for HKEY_CURRENT_USER\Software\SDR-RADIO.com (V3)\Console\Ident0 and C:\Users\<myusername>\AppData\Roaming\SDR-RADIO.com (V3)\C

#sdrconsolev3

This is working very well indeed. I am using an LNB with a high stability oscillator and the sdr-console locks and stays locked to the beacon.

#rsp1a #satellites #sdrconsolev3 #qo100

A bit beside the discussed thread, but related, is that the only real thing for me on which I rely is the SNR indication which is both a nice feature on SDRuno and SDRconsole. Also your ears are not t

#sdrconsolev3 #airspyhfplus

Hi, Don’t change the center frequency! It’s probably happening because you can’t set the dongle to an exact frequency, common in some tuner chips at high frequency. Simon Brown, G4ELI https://www.sdr-

#qo100 #sdrconsolev3

Hi, I understand, but as I always say – time and I have my own projects as well. I am sure adding TX support for HackRF is easy. Simon Brown, G4ELI https://www.sdr-radio.com

#hackrf #feature #sdrconsolev3

I sometimes use a a virtual audio cable to decode the Itty and mute the sound to the speaker and read the decodes another time. With the sound muted and using a vac, you can still do other things with

#sdrconsolev3