a hint ... while you are txing ... pull volume slider up (to hear the downlink for finetune) after next ptt release and prtess again it is back to 0 (or where you have set it) some users do not mute c

#adalmpluto #qo100

Hi Simon, As we discussed on QO-100 last night can I suggest an easy access button (perhpas in the TX pane) where you can rapidly enable/disable the Rx mute ? My pluto sdr has a TCXO and there is ofte

#adalmpluto #qo100

Just an idea: SDR Console syncs the RX-frequency with the Geostationary Satellite Beacon - Plugin. - Well done! I dream about the same for the TX-frequency (as we know, the frequency stability of plut

#request #pluto #satellites #qo100

Hi Am using Adalm Pluto. Works perfectly in narrow band modes. However, I cannot see any signals in the wide band sections. Polarisation change (18 V)seems to work fine. I do not want to decode, just

#qo100

Dear OMs and YLs, since yesterday i have had a problem with pluto transmission. The transmission frequency can no longer be synchronized with the reception frequency and always remains at 10489750000

#sdrconsolev3 #sdr-consolev3 #sdrconsole #qo100 #pluto

This is working very well indeed. I am using an LNB with a high stability oscillator and the sdr-console locks and stays locked to the beacon.

#rsp1a #satellites #sdrconsolev3 #qo100

Hi, Don’t change the center frequency! It’s probably happening because you can’t set the dongle to an exact frequency, common in some tuner chips at high frequency. Simon Brown, G4ELI https://www.sdr-

#qo100 #sdrconsolev3

Hello Shimon. Look like I find why beacon runs out of sync. When I do small shift of waterfall - signal got small offset. Pse look video here : https://1drv.ms/v/s!Auurs2F0cQKFgaN_uLcTkgw8r_rmqA Here

#qo100 #sdrconsolev3

digikey and mouser should have them for 10 bucks ... Am 22.06.2020 um 20:04 schrieb claus.moessner@...:

#qo100 #sdrconsolev3

Hello Simon, the software runs over night without loosing the sync. Thanks a lot for taking care (donation done :-) Claus

#qo100 #sdrconsolev3

Hi, That screenshot looks good. Simon Brown, G4ELI https://www.sdr-radio.com

#qo100 #sdrconsolev3

As I said I'm pretty new with this software Need a while to understand. Offset was mentioned wrong, its about 150kHz not MHz. I now do the compensation via "converter definitions", before I changed th

#qo100 #sdrconsolev3

tcxo is a digitally compensated one ... that is the reason for those sudden jumps (so can not be used!!) second unmodified lnb has not 150mhz offset but 7.18 kc ... sadly you have all boxes in the dsp

#qo100 #sdrconsolev3

Ah, HackRF – I don’t need the Radio pane – there isn’t one. Simon Brown, G4ELI https://www.sdr-radio.com

#qo100 #sdrconsolev3

OK, Getting better. Now please add a screenshot showing the information as in https://www.sdr-radio.com/EsHail-2#&gid=1497719097&pid=1 Specifically: Frequency Radio I want to see the downconverter set

#qo100 #sdrconsolev3

ok, added as attachment now. Picture one is modified LNB Picture two is unmodified LNB (same type) -> sync seems to work stable now, but LNB has about 150Mhz offset after warming up :-( Yes, will chan

#qo100 #sdrconsolev3

NO !!! It is too small to read ! You must fix your hardware. Simon Brown, G4ELI https://www.sdr-radio.com

#qo100 #sdrconsolev3

Better now? Do not know why this happens. I did a TCXO modification by myself, may be I did a mistake. I will climb to the roof later on, change the LNB with an unmodified different type and double ch

#qo100 #sdrconsolev3

Claus, These are too small ☹ . I want to see the first screenshot FULL SIZE as an attachment please. The radio must be running when you make the screenshot. Why do you have this discontinuity? Simon B

#qo100 #sdrconsolev3

Second trial, within picture one you can already see how the system runs out of sync. Without this frequency hops the regulator works fine, even with a big drift while the system is heating up.

#qo100 #sdrconsolev3