I am using the Evariste fw to give me PTT via a relay board in the Pluto and it works fine with narrow band QO100.

#adalmpluto #feature #ptt #future

Rob, “for the brave” seems to sum it up! I guess first you need to be sure you know how to recover a "bricked" Pluto! The Forum does seem to be the place to go to see what problems (if any) others hav

#adalmpluto #feature #ptt #future

Sorry for being a bit slow but reading the page at https://www.f5uii.net/en/actualites/dual-ptt-switching-board-for-adalm-pluto-sdr/ , to use the board, I first have to install fw 0.31 and then instal

#adalmpluto #feature #ptt #future

Hi Sigi, Thanks for your suggestion. I had wondered whether the fw was ok for not-datv use of Pluto? But it seems it is...? If I drag and drop the evariste fw, do I still have the same virtual disk in

#adalmpluto #feature #ptt #future

Guess who asked evariste for that fw add on... Guess who had the clever idea if using two gpo pins... Am 06.01.2021 23:35 schrieb Noel f6bgc <f6bgc74@...>:

#adalmpluto #feature #ptt #future

Check f5uii web site https://www.f5uii.net/en/actualites/dual-ptt-switching-board-for-adalm-pluto-sdr/ Installed on my Pluto, it works perfectly ! 73 - noel f6bgc

#adalmpluto #feature #ptt #future

You can use the firmware from evariste It switches a relais on gpo pin just fine A usb relais only works if pluto is direct connected to your pc But not if you control your pluto via ethernet with a n

#adalmpluto #feature #ptt #future

Rob, The standard firmware from AD does not work with GPO, so you must use a USB relay. For further help please use the forums (URL below). Simon Brown, G4ELI https://www.sdr-radio.com

#adalmpluto #feature #ptt #future

Hi, Could I ask what is the current situation regarding PTT for the Pluto? Is it implemented via the GPO pins in the latest version of SDRC and does it work with the stock AD fw (0.31 I believe is the

#adalmpluto #feature #ptt #future

Ciao Simon, ok 73 Rocco IK8XLD

#future #request

Hi, Please use https://forum.sdr-radio.com and add the request there. Simon Brown, G4ELI https://www.sdr-radio.com

#future #request

Hello Simon, I would like to ask you if there is the possibility to add another type of converter in sdrconsole, in the CONVERTER DEFINITIONS menu. Currently available converters are working subtracti

#future #request

Hi, You need to register separately for the new forum - it is separate from io.groups. ================================ Need help with SDR Console? If you have a problem: Go to https://www.sdr-radio.c

#future

this is not possible, I can not log in, always got this message: "You have specified an incorrect username. Please check your username and try again. If you continue to have problems please contact th

#future

this is not possible, I can not log in, always got this message: "You have specified an incorrect username. Please check your username and try again. If you continue to have problems please contact th

#future

You need to post this on the forum under the Requests category. https://forum.sdr-radio.com:4499 Regards, George, NJ3H Redmond, Oregon USA DMR ID: 3141315 AllStar Node: 49246EchoLink Node NJ3H-L: 3135

#future

Please add an interface for MAP65 broadband software decoder for digital modes like JT65 etc. There have been an interface in older version, as I know. Will be used for Hamradio and for moonbounce. By

#future

And the next request would be 15 degrees off to the South and 30 degrees to the North and more numbers for other cardinal directions.... {O,o} <- Joanne lives where North is almost mythological. The N

#future

No, I don't think so Al. I think Phil is asking to be able to optionally set the minimum elevation to a value higher than 20 Deg? Not remove the ability to set it lower than 80 Deg. 73 Max

#future

user setable border starting at MINUS 10 degrees (yes below horizon) ... reason is then tracking of frequency starts BEFORE the sat is there min elevation set HIGHER is on the user end (if he does not

#future