Hi Sigi, The UBX board in the X310 has a max theoretical bandwith of 160MHz. At 50MHz Bandwith (max BW I can set in SDR console) I see about 14 to15% load on the 10G link, but the GTX 1650 gets loaded

Hello All, finally I achieved communication between SDR console and my Ettus x310 (by going back to the old UHD Firmware 3.15) . Initially SDR console crashed after flashing when I started SDRconsole

Hello Jolly, I still have problems getting the x310 to work. This morning I flashed succesfully the old firmware/imge from UHD 3.15. SDR console recognises now the X310 connected via 1G link, if the 1

#sdrconsolev3 #ettus

Good morning Erik, yes, the documentation could be better in particular for "OLD Man" like me.....with little software skills I wonder if I will get the X310 to communicate with SDR Console AFTER I re

Hello Eric, What image did you install - an older one from UHD revision 3.5? As I am not really familiar with software at all, I had a lot of difficulties in the beginning to properly use the UHD comm

Just for info: This displayed link is gone - 73 Charly

Ettus USRP N200 Test with Beta SDR Console ===================================== Ettus_USRP N200 with WBX board fitted running under SDR console (Beta, Jan 2022) and UHD 4.0 driver WBX Bandwith set to

#sdrconsolev3 #ettus

Hi Larry Sorry, I missed your question in 2021 Larry. Busy on the ham bands and many other things to do , so I did not monitor this chat for a very long time. Actually there was no issue at all to con

#sdrconsolev3 #ettus

Hello Ray, I you have some spare time pse let me know what firmware you use for your USRP X310 to communicate with SDR console. Pse mention also the UHD release, Do you install Winx64_VS2019 or an oth

#sdrconsolev3 #ettus

Hello Eric, did you ever get a reply or a working image for your usrp X310 I had no problem to get an USRP N200 working with SDR-Console, but my USRP x310 was never recognised in SDR console. Tried ma

Hello, I got an Ettus N200/wbs daughterboard working in SDR console - after updating to last firmware. Before the Ettus driver reported a software discrepancy. However I cound not manage to run the fu

#sdrconsolev3 #ettus

Hello Simon, just received an USPR N-200 with 50-2200 WBX MHz daughter board. (and a spare LFrx-LF, which I don't need) As I am not really competent with software, it took me some time to read manuals

Thanks for reading ma question and proposing diffent solutions. I use only one receiver on qo100 - (plus the default one for the beacon) Seems the easiest way ist to try the "listen to ..device" propo

Hello, May be I have not found an already existing option to route audio in SDR console to an external prg (other than CW skimmer) via a virtual audio cable. Tried to activate VB-cable (in Skimmer set

Very nice software Simon. Now with Oscar100 up, I started to use SDR console with SDRplay on a regular base, sometimes tracking in parallel an older IC R7000 via Omnirig (a unit with a big tuning knob

Hello Simon Do you plan in the nearby future to extend the OMNIRIG support also to the latest OMNIRIG Version 2.0 , which can address up to four TRX/RX. Just installed SDR console as OCAR 100 (LNB) IF

Thanks Jeffry and Dennis. I finally got the powermate working. Retrospective a banal issue: The powermate driver installed ok, but I did not notice the (hidden) "setup icon" in the launch bar (right h

Hello, Not really familiar with internal software aspects, I made good progress using SDR Console V3.with an SDRPlay. Performance seems even better on 6m than my Icom 7300, and I use the combination f

I have seen a ham made video you tube in which a (low cost) Griffin powermate was has been as Tuningknob in SDR console. So far I managed to get the Griffin software running in Win7/64 but due to lack

Hi Ken, I thought at first glance my powermate installation failed as well under In7/64 - uninstalled and installed a few times but no VISIBLE result. Actually the installation was ok, there is no fee