Hello, I would really appreciate if the quick access toolbar personalization will be saved on exit. Or maybe adding antennas switch to it so it's accessible from any tabs. Again thanks for all greats

#feature #sdrconsolev3 #request

I finally was able to try my SpyVerter with RTL-SDR v3 dongle. The first problem I encountered was attempting to calibrate against WWV on 10 MHz. With the 120 MHz correction factor enabled, the receiv

#rtl #request

Hello, Just want to know if possible to send CAT commands (freq, mode, bandwith, etc) to SDR-Console via UDT/TCP network. Some kind of API available for that ? This would help programmers to develop k

#request

Hi Simon, congratulations for your wonderful software. You know that using SDRCONSOLE with ES'HEIL-2 it is necessary to reduce the audio from SDR when transmitting. If you use a TX that has no CAT to

#request

Hi guys! I'm a newbie with SDR Console v3, just found out last week about this excellent software and I am hoping to financially support it financially in the very near future. I have previously been

#rtl #rtldrivers #request #feature

Problem with rig syncing via CAT for QO-100 satellite operation: I am using an Elecraft K3 for TX via upconverter to 2400 MHz. The CAT sync seems to work when I set the K3 config meny (in the radio) t

#request

Hi, Simon, another minor suggestion... The present cue is a colour-coded gradient-fill for the selected RX IF. With many RX colours, this can be hard to distinguish from the "empty" (unselected) fill,

#request

Simon, as an alternative to just "Add" RX, this would save me quite a few keystrokes and annoying mistakes.

#request

Simon, following up one of my remarks from a while ago (and a mention by another user), could I please make a firm request for low-level or muted audio? To be applied whenever new RX created AND whene

#request

Hi, Simon Two small enhancements to this dialog would be greatly appreciated: 1. Add checkmark to the currently selected channel configuration 2. Make channel configuration a sub-menu of each device s

#request

Low priority. When running several RX, even with just a single SDRC instance, I find it too easy to lose track of which devices they output to (e.g. left and right ‘phones for parallel channel checkin

#request

Listening to VHF-FM, I sometimes come across "duplicates" with an audible time delay that may(?) be explained by simulcast distribution latency. This can be as high as 100ms, possibly more, and makes

#request

Simon is this nice option Simon is this option also possible with your software like the original perseus sdr software have or in the future ===========================================================

#request

Hello, Is it possible someday to add 30kHz tuning steps for OIRT-tuning in BFM section? This would be great add-on for OIRT-band DXing :) Best Regards: Janne

#request

Is it possible to add the option to stop the spectrum and waterfall displays? It eats up a lot of CPU resources but isn’t always needed. Like when trying to decode data on multiple frequencies. The lo

#request #sdrconsolev3

Hello, I designed an add-on-board for the Adalm Pluto which derives the 40MHz for the Pluto as well as the 25MHz for the LNB from the same VCTCXO. In addition this board has the option to connect a gp

#pluto #request

Hello Simon, Upgrading SDR-Console up to v.3.0.11 I learned that it got support for the WINRADIO Sigma. Please make support for WINRADIO G31DDC too. I like very much using my SDRplay RSP1A with your f

#request

Hi, I would like to add my support for Yuri's request for the WinRadio G-31 Excalibur support. Would really be great. (even if only 32 bit) Thanks for considering, Bob

#request

Hi, I'm using SDR-Console for receiving QO-100. Works fine ! I've different ways to transmit. One is old and analog and the others are capable of being CAT-controlled like my FT-100. And I'm thinking

#qo100 #request #sdrconsolev3 #feature

Hello, I've configure two lite jog upper left to control audio filters. But if i change channel with the deck I lost the functionality because we can't assign multi-channel to same function. So i'll t

#feature #midi #request #sdrconsolev3