Date   

Re: Looking for a HL2

Simon Brown
 

Agreed,

 

ENOB & BDR will be similar, more important is ADC linearity.

 

Anyway, just ordered a Hermes card for $389 – that’s a *very* good price. So I guarantee support!

 

Simon Brown, G4ELI

https://www.sdr-radio.com

 

From: main@SDR-Radio.groups.io <main@SDR-Radio.groups.io> On Behalf Of Conrad, PA5Y
Sent: 17 February 2022 14:51
To: main@SDR-Radio.groups.io
Subject: Re: [SDR-Radio] Looking for a HL2

 

Hello Ingolf.

 

I had an ANAN-10E and the receiver was very good, later on I bought an ANAN-100D which I believe was a 16 bit ADC. The summer Es season on 6m is quite punishing and I found the differences between the ANAN-10E and ANAN-100D to be small. The ENOB of a 16 bit ADC and 14 bit ADCs end up being quite similar. If you look at the SFDR of the LTC-2208-14 (98dB) and the LTC-2209-16 (100dB) there is only 2dB difference. It depends what you will use it for but you know that 😊

 

I will order one for use with uwave transverters. I don’t expect many dynamic range problems on 23cms and above.

 

73

 

Conrad PA5Y

 

From: main@SDR-Radio.groups.io <main@SDR-Radio.groups.io> On Behalf Of sm6fhz via groups.io
Sent: 17 February 2022 09:25
To: main@SDR-Radio.groups.io
Subject: Re: [SDR-Radio] Looking for a HL2

 

Thanks Mark.

Simon, if you read this;
Does SDRC support the Hermes board that Apache Labs (ANAN) is producing and marketing?
https://apache-labs.com/al-products/1022/Open-HPSDR-Hermes-14-bit-ADC-EP3C25-Transceiver-Card-Assembled--Tested.html

Another question about this board. It says 14 bit ADC in the web-page but the ADC in the original Hermes schematic is an 16 bit ADC.
Will this board deliver the same performance as the original Hermes design?

73 / Ingolf, SM6FHZ


--
- + - + -
Please use https://forum.sdr-radio.com:4499/ when posting questions or problems.


Re: Looking for a HL2

Conrad, PA5Y
 

Hello Ingolf.

 

I had an ANAN-10E and the receiver was very good, later on I bought an ANAN-100D which I believe was a 16 bit ADC. The summer Es season on 6m is quite punishing and I found the differences between the ANAN-10E and ANAN-100D to be small. The ENOB of a 16 bit ADC and 14 bit ADCs end up being quite similar. If you look at the SFDR of the LTC-2208-14 (98dB) and the LTC-2209-16 (100dB) there is only 2dB difference. It depends what you will use it for but you know that 😊

 

I will order one for use with uwave transverters. I don’t expect many dynamic range problems on 23cms and above.

 

73

 

Conrad PA5Y

 

From: main@SDR-Radio.groups.io <main@SDR-Radio.groups.io> On Behalf Of sm6fhz via groups.io
Sent: 17 February 2022 09:25
To: main@SDR-Radio.groups.io
Subject: Re: [SDR-Radio] Looking for a HL2

 

Thanks Mark.

Simon, if you read this;
Does SDRC support the Hermes board that Apache Labs (ANAN) is producing and marketing?
https://apache-labs.com/al-products/1022/Open-HPSDR-Hermes-14-bit-ADC-EP3C25-Transceiver-Card-Assembled--Tested.html

Another question about this board. It says 14 bit ADC in the web-page but the ADC in the original Hermes schematic is an 16 bit ADC.
Will this board deliver the same performance as the original Hermes design?

73 / Ingolf, SM6FHZ


Re: Adding my receiver to the server

Simon Brown
 

https://www.sdr-radio.com/server

 

Simon Brown, G4ELI

https://www.sdr-radio.com

 

From: main@SDR-Radio.groups.io <main@SDR-Radio.groups.io> On Behalf Of George Stein - NJ3H via groups.io
Sent: 17 February 2022 11:04
To: main@SDR-Radio.groups.io
Subject: [SDR-Radio] Adding my receiver to the server

 

Greetings, 

I am looking for detailed instructions to add my receiver to the list of servers. I have also checked YouTube but only find how to access radios already on the list.

I would appreciate help in getting started with adding my receiver to the server list.

Thanks, 
George 


--
- + - + -
Please use https://forum.sdr-radio.com:4499/ when posting questions or problems.


Re: IARU Region band plans

michel soldevila
 

Right version of SDR Console ? I have tying for quite a lon time to install the bandplan on a wrong version ...
73, Michel (F1GOC)


Re: One more newbie question

michel soldevila
 

HI,
Thanks all for your answers
I realize that my question was poorly worded (I'm French, nobody's perfect ;-)): I was wondering what the difference was in terms of receiving performance (sensitivity, noise, etc.) between a 2MHz bandwidth (which Simon recommended) and a bandwidth of 10MHz ...
73, Michel (F1GOC)


Adding my receiver to the server

George Stein - NJ3H
 

Greetings, 

I am looking for detailed instructions to add my receiver to the list of servers. I have also checked YouTube but only find how to access radios already on the list.

I would appreciate help in getting started with adding my receiver to the server list.

Thanks, 
George 


Re: Looking for a HL2

sm6fhz
 

Thanks Mark.

Simon, if you read this;
Does SDRC support the Hermes board that Apache Labs (ANAN) is producing and marketing?
https://apache-labs.com/al-products/1022/Open-HPSDR-Hermes-14-bit-ADC-EP3C25-Transceiver-Card-Assembled--Tested.html

Another question about this board. It says 14 bit ADC in the web-page but the ADC in the original Hermes schematic is an 16 bit ADC.
Will this board deliver the same performance as the original Hermes design?

73 / Ingolf, SM6FHZ


Re: IARU Region band plans

Simon Brown
 

What have you tried?

Ribbon bar, View, Spectrum, Band plan, Database, Select.

 

Simon Brown, G4ELI

https://www.sdr-radio.com

 

From: main@SDR-Radio.groups.io <main@SDR-Radio.groups.io> On Behalf Of Fernando Gómez
Sent: 17 February 2022 03:57
To: main@sdr-radio.groups.io
Subject: Re: [SDR-Radio] IARU Region band plans

 

I have tried to import all three files, but without success. What is the procedure? Thanks!!

Fernando

 

Enviado desde Correo para Windows

 

De: Max
Enviado: miércoles, 16 de febrero de 2022 21:32
Para: main@sdr-radio.groups.io
Asunto: Re: [SDR-Radio] IARU Region band plans

 

On Wed, Feb 16, 2022 at 07:05 PM, Simon Brown wrote:

Ham Radio Bandplan for SDR# - SZ1A

 

Designed for SDR# but can be imported into SDR Console.

Works very well. Thanks for the tip Simon. I've actually asked him if he could add FT8 and SSTV but they are fine even without.

Max

 


--
- + - + -
Please use https://forum.sdr-radio.com:4499/ when posting questions or problems.


Re: IARU Region band plans

Fernando Gómez
 

I have tried to import all three files, but without success. What is the procedure? Thanks!!

Fernando

 

Enviado desde Correo para Windows

 

De: Max
Enviado: miércoles, 16 de febrero de 2022 21:32
Para: main@sdr-radio.groups.io
Asunto: Re: [SDR-Radio] IARU Region band plans

 

On Wed, Feb 16, 2022 at 07:05 PM, Simon Brown wrote:

Ham Radio Bandplan for SDR# - SZ1A

 

Designed for SDR# but can be imported into SDR Console.

Works very well. Thanks for the tip Simon. I've actually asked him if he could add FT8 and SSTV but they are fine even without.

Max

 


Re: How to set up SDRC as a Server, a step by step guide on setting up the computer to be used as a server

Kriss Kliegle KA1GJU
 

There's one similar to mine here:
https://sdr-radio.groups.io/g/main/files/Version3ServerHelpFiles/SDRConsoleV3-ServerGuide2.pdf

Start on slide/page 17 for setting up your own server.

It's time I repeat the process since some of the screens/windows have changed since I wrote it.

I'll try and write a new one this week on my days off.

73 Kriss KA1GJU


Re: Looking for a HL2

Mark Cayton
 
Edited

Ingolf,

Simon's website (at https://www.sdr-radio.com/anan-firmware) states:

"The OpenHPSDR Ethernet Protocol (aka protocol II) is the only protocol which will be supported for ANAN transceivers. This protocol is supported via firmware on TAPR Hermes boards and ANAN transceivers from Apache Labs."

You probably should check with Simon but I'm interpreting that to say that he supports the Hermes board if it's running Protocol II (that firmware is available here: https://github.com/TAPR/OpenHPSDR-Firmware/tree/master/Protocol%202).

I will say that I've run my ANAN 7000 DLE MKII using SCRC just fine. I don't currently use SDRC on that radio only because SDRC doesn't support PureSignal.

Mark K1LSB


Re: Elad FDM DUO - no RX / input stream #EladDUOrxtx

Max
 

On Wed, Feb 16, 2022 at 09:28 PM, <hb9bhu@...> wrote:
Yes Max, I followed that page.
I attached the screenshot with the home tab.
Try disabling Auto Mute and/or Noise blanker

Max


Re: Elad FDM DUO - no RX / input stream #EladDUOrxtx

hb9bhu@...
 

Yes Max, I followed that page.
I attached the screenshot with the home tab.


Re: IARU Region band plans

Max
 

On Wed, Feb 16, 2022 at 07:05 PM, Simon Brown wrote:

Ham Radio Bandplan for SDR# - SZ1A

 

Designed for SDR# but can be imported into SDR Console.

Works very well. Thanks for the tip Simon. I've actually asked him if he could add FT8 and SSTV but they are fine even without.

Max


IARU Region band plans

Simon Brown
 

Hi,

 

Ham Radio Bandplan for SDR# - SZ1A

 

Designed for SDR# but can be imported into SDR Console.

 

Simon Brown, G4ELI

https://www.sdr-radio.com

 


--
- + - + -
Please use https://forum.sdr-radio.com:4499/ when posting questions or problems.


Re: Looking for a HL2

Michael Durkin
 

Opss ... I meant Ravi


On Wed, Feb 16, 2022, 8:31 AM Michael Durkin via groups.io <Kc7noa=gmail.com@groups.io> wrote:
I'm waiting on a response from Seri regarding mine

On Wed, Feb 16, 2022, 6:35 AM sm6fhz <ingolf.fhz@...> wrote:
Hi Mark.
Thanks for the hint.
I guess that is the full fledged Hermes board covering up to 55 MHz.
I am not sure SDRC supports this breed of Hermes. I only found support for the HL2.
73 / Ingolf, SM6FHZ


Re: Looking for a HL2

Michael Durkin
 

I'm waiting on a response from Seri regarding mine


On Wed, Feb 16, 2022, 6:35 AM sm6fhz <ingolf.fhz@...> wrote:
Hi Mark.
Thanks for the hint.
I guess that is the full fledged Hermes board covering up to 55 MHz.
I am not sure SDRC supports this breed of Hermes. I only found support for the HL2.
73 / Ingolf, SM6FHZ


Re: How to set up SDRC as a Server, a step by step guide on setting up the computer to be used as a server

Ash
 

I found this thread two years later and all the images are missing. Would it be possible to resurrect them?


Re: One more newbie question

Jim Smith G0OFE
 

Record a 10Mhz chunk, then use Datafile Editor to pull out 1Mhz chunks.

================================
Need help with SDR Console? If you have a problem:
Go to https://www.sdr-radio.com/support
Please follow instructions in that link.
===================================
Jim, Bournemouth, Dorset. IO90BR.
Elad FDM-S2, Airspy HF+, SDRPlay and Funcube Dongle SDR Recievers
8-element OP-DES for Band 2, 8-element LFA for 2m, 3-element LFA for 6m, 20m Windom for HF,. Wellbrook 1530 Loop for LF


On 16/02/2022 11:30, Siegfried Jackstien wrote:

i do not know how simon handles 1x10 or 10x1 mhz chunks on recording (if it is lossless to split in 10 receivers or not) ,,, in principle these could be lossless ... it even should be possible to make one big sized recording and split it later (to analyze only a part of it then)

make a 10 megs wide recording (if your hardware allows it) ... play back that file and set 10 receivers .. each 1 megs wide ... and that "should" be lossless

or play that file back ten times with a single receiver but on every play back set the receiver 1 megs different (yes that may take a while hi hi)

it that really is lossless or not ... no idea ;-)

"ask the boss ... he may know" ... wink wink

dg9bfc sigi

Am 16.02.2022 um 09:52 schrieb jdow:
Fewer aliases right around the boundaries of adjacent recordings comes to mind.
{o.o}

On 20220215 16:03:00, Siegfried Jackstien wrote:

maybe cpu load is different keeping several recording running in parallel or one bigger (needs for sure a fast ssd and/or a hefty cpu)... same with analyzing them ... ... in fact i can not tell you the real differences .. maybe Simon can give a more detailed answer what is the difference of 1x10 or 10x1 mhz chunks on recording an analyzing (numbers are just examples)

dg9bfc sigi

Am 15.02.2022 um 21:49 schrieb michel soldevila:
Thanks Sigi.
But then why offer 9 bandwidths from 500kHz to 10 MHz, if the performances are the same? There is necessarily something that changes depending on the bandwidth, but what?
73, Michel (F1GOC)


Re: Looking for a HL2

sm6fhz
 

Hi Mark.
Thanks for the hint.
I guess that is the full fledged Hermes board covering up to 55 MHz.
I am not sure SDRC supports this breed of Hermes. I only found support for the HL2.
73 / Ingolf, SM6FHZ