Date   

Re: Where do I find Protocol 2 firmware

Carl Moreschi <n4py3@...>
 

No I have not downloaded Thetis yet.

Carl Moreschi N4PY
58 Hogwood Rd
Louisburg, NC 27549
www.n4py.com

On 9/30/2017 4:53 PM, paul newcombe wrote:
Not had that problem. It connected and ran on sdrc with no problems at
all. all problems i had were due to the 100 hub i had conected. Did you
get Thetis to run with your anan? Although the waterfall with sdrc is
far better to see stations on getting Thetis to work should help get
sdrc working.


Sent on a Sprint Samsung Galaxy Note® II


-------- Original message --------
From: Carl Moreschi
Date:09/30/2017 4:35 PM (GMT-05:00)
To: main@SDR-Radio.groups.io
Subject: Re: [SDR-Radio] Where do I find Protocol 2 firmware

Paul,

You have been very helpful. It looks like my router does not support
gigabit. I connected directly to my lan card and now SDRConsole
discovers the radio. It connects but nothing happens.

Carl Moreschi N4PY
58 Hogwood Rd
Louisburg, NC 27549
www.n4py.com <http://www.n4py.com>

On 9/30/2017 1:24 PM, paul newcombe wrote:
Are all of your cat5 connections/hubs/routers etc 1000's ? If you have
any 100s in there you will not see your anan.

If the answer to the above is yes then go back to the bootloader screen
and asign your anan a fixed ip.

Again i know nothing and most people will agree with me about that so
please read up before doing anything i say :)


Sent on a Sprint Samsung Galaxy Note® II


-------- Original message --------
From: Carl Moreschi
Date:09/30/2017 1:17 PM (GMT-05:00)
To: main@SDR-Radio.groups.io
Subject: Re: [SDR-Radio] Where do I find Protocol 2 firmware

Well after loading the 100D protocol 2 file with HPSDRprogrammer,
nothing can find my 100D now. Now what?

Carl Moreschi N4PY
58 Hogwood Rd
Louisburg, NC 27549
www.n4py.com <http://www.n4py.com> <http://www.n4py.com>

On 9/30/2017 12:43 PM, Barry Jablonski wrote:
Good information Paul,

For the 100D you need to go up two levels and follow 100D link:

https://github.com/TAPR/OpenHPSDR-Firmware/tree/91c058115b83cf652200966f377e19cbe3603219/Protocol%202/Angelia%20(ANAN-100D)

Barry
WB2ZXJ





Re: Where do I find Protocol 2 firmware

paul newcombe <G6YZC@...>
 

Not had that problem. It connected and ran on sdrc with no problems at all. all problems i had were due to the 100 hub i had conected. Did you get Thetis to run with your anan?   Although the waterfall with sdrc is far better to see stations on getting Thetis to work should help get sdrc working. 


Sent on a Sprint Samsung Galaxy Note® II


-------- Original message --------
From: Carl Moreschi
Date:09/30/2017 4:35 PM (GMT-05:00)
To: main@SDR-Radio.groups.io
Subject: Re: [SDR-Radio] Where do I find Protocol 2 firmware

Paul,

You have been very helpful.  It looks like my router does not support
gigabit.  I connected directly to my lan card and now SDRConsole
discovers the radio.  It connects but nothing happens.

Carl Moreschi N4PY
58 Hogwood Rd
Louisburg, NC 27549
www.n4py.com

On 9/30/2017 1:24 PM, paul newcombe wrote:
> Are all of your cat5 connections/hubs/routers etc 1000's ? If you have
> any 100s in there you will not see your anan.
>
> If the answer to the above is yes then go back to the bootloader screen
> and asign your anan a fixed ip.
>
> Again i know nothing and most people will agree with me about that so
> please read up before doing anything i say :)
>
>
> Sent on a Sprint Samsung Galaxy Note® II
>
>
> -------- Original message --------
> From: Carl Moreschi
> Date:09/30/2017 1:17 PM (GMT-05:00)
> To: main@SDR-Radio.groups.io
> Subject: Re: [SDR-Radio] Where do I find Protocol 2 firmware
>
> Well after loading the 100D protocol 2 file with HPSDRprogrammer,
> nothing can find my 100D now. Now what?
>
> Carl Moreschi N4PY
> 58 Hogwood Rd
> Louisburg, NC 27549
> www.n4py.com <http://www.n4py.com>
>
> On 9/30/2017 12:43 PM, Barry Jablonski wrote:
>>  Good information Paul,
>>
>>  For the 100D you need to go up two levels and follow 100D link:
>>
>>
> https://github.com/TAPR/OpenHPSDR-Firmware/tree/91c058115b83cf652200966f377e19cbe3603219/Protocol%202/Angelia%20(ANAN-100D)
>>
>>  Barry
>>  WB2ZXJ
>>
>
>
>
>




Re: Where do I find Protocol 2 firmware

Carl Moreschi <n4py3@...>
 

Paul,

You have been very helpful. It looks like my router does not support gigabit. I connected directly to my lan card and now SDRConsole discovers the radio. It connects but nothing happens.

Carl Moreschi N4PY
58 Hogwood Rd
Louisburg, NC 27549
www.n4py.com

On 9/30/2017 1:24 PM, paul newcombe wrote:
Are all of your cat5 connections/hubs/routers etc 1000's ? If you have
any 100s in there you will not see your anan.

If the answer to the above is yes then go back to the bootloader screen
and asign your anan a fixed ip.

Again i know nothing and most people will agree with me about that so
please read up before doing anything i say :)


Sent on a Sprint Samsung Galaxy Note® II


-------- Original message --------
From: Carl Moreschi
Date:09/30/2017 1:17 PM (GMT-05:00)
To: main@SDR-Radio.groups.io
Subject: Re: [SDR-Radio] Where do I find Protocol 2 firmware

Well after loading the 100D protocol 2 file with HPSDRprogrammer,
nothing can find my 100D now. Now what?

Carl Moreschi N4PY
58 Hogwood Rd
Louisburg, NC 27549
www.n4py.com <http://www.n4py.com>

On 9/30/2017 12:43 PM, Barry Jablonski wrote:
Good information Paul,

For the 100D you need to go up two levels and follow 100D link:

https://github.com/TAPR/OpenHPSDR-Firmware/tree/91c058115b83cf652200966f377e19cbe3603219/Protocol%202/Angelia%20(ANAN-100D)

Barry
WB2ZXJ



Re: Where do I find Protocol 2 firmware

paul newcombe <G6YZC@...>
 

Are all of your cat5 connections/hubs/routers etc 1000's ?   If you have any 100s in there you will not see your anan.   

If the answer to the above is yes then go back to the bootloader screen and asign your anan a fixed ip.

Again i know nothing and most people will agree with me about that so please read up before doing anything i say :)


Sent on a Sprint Samsung Galaxy Note® II


-------- Original message --------
From: Carl Moreschi
Date:09/30/2017 1:17 PM (GMT-05:00)
To: main@SDR-Radio.groups.io
Subject: Re: [SDR-Radio] Where do I find Protocol 2 firmware

Well after loading the 100D protocol 2 file with HPSDRprogrammer,
nothing can find my 100D now.  Now what?

Carl Moreschi N4PY
58 Hogwood Rd
Louisburg, NC 27549
www.n4py.com

On 9/30/2017 12:43 PM, Barry Jablonski wrote:
> Good information Paul,
>
> For the 100D you need to go up two levels and follow 100D link:
>
> https://github.com/TAPR/OpenHPSDR-Firmware/tree/91c058115b83cf652200966f377e19cbe3603219/Protocol%202/Angelia%20(ANAN-100D)
>
> Barry
> WB2ZXJ
>




Re: Where do I find Protocol 2 firmware

Carl Moreschi <n4py3@...>
 

Well after loading the 100D protocol 2 file with HPSDRprogrammer, nothing can find my 100D now. Now what?

Carl Moreschi N4PY
58 Hogwood Rd
Louisburg, NC 27549
www.n4py.com

On 9/30/2017 12:43 PM, Barry Jablonski wrote:
Good information Paul,

For the 100D you need to go up two levels and follow 100D link:

https://github.com/TAPR/OpenHPSDR-Firmware/tree/91c058115b83cf652200966f377e19cbe3603219/Protocol%202/Angelia%20(ANAN-100D)

Barry
WB2ZXJ


Re: Where do I find Protocol 2 firmware

paul newcombe <G6YZC@...>
 

I forgot the most important link.....



http://sdr-radio.com/v3_preview_downloads

Afterall the reason you are loading P2 is to run SDRC as your tx/rx with the ANAN. 



From: main@SDR-Radio.groups.io <main@SDR-Radio.groups.io> on behalf of Barry Jablonski <bjablonski@...>
Sent: Saturday, September 30, 2017 12:43 PM
To: main@SDR-Radio.groups.io
Subject: Re: [SDR-Radio] Where do I find Protocol 2 firmware
 
Good information Paul,

For the 100D you need to go up two levels and follow 100D link:

https://github.com/TAPR/OpenHPSDR-Firmware/tree/91c058115b83cf652200966f377e19cbe3603219/Protocol%202/Angelia%20(ANAN-100D)
github.com
OpenHPSDR-Firmware - This is the verilog code for the various FPGA in the OpenHPSDR Radios



Barry
WB2ZXJ


Re: Where do I find Protocol 2 firmware

Barry Jablonski
 

Good information Paul,

For the 100D you need to go up two levels and follow 100D link:

https://github.com/TAPR/OpenHPSDR-Firmware/tree/91c058115b83cf652200966f377e19cbe3603219/Protocol%202/Angelia%20(ANAN-100D)

Barry
WB2ZXJ


Re: Where do I find Protocol 2 firmware

paul newcombe <G6YZC@...>
 


These may be what you are looking for.


Please remember that I am a total idiot when it comes to computers so read well before you follow anything I say.


bootloaderHPSDRBootloader



http://openhpsdr.org/download.php


protocol 2

https://github.com/TAPR/OpenHPSDR-Firmware/blob/91c058115b83cf652200966f377e19cbe3603219/Protocol%202/ANAN-10E%20%26%20100B/Hermes_v10.2.rbf


Thetis


https://github.com/TAPR/OpenHPSDR-Thetis


From: main@SDR-Radio.groups.io <main@SDR-Radio.groups.io> on behalf of Carl Moreschi <n4py3@...>
Sent: Saturday, September 30, 2017 12:09 PM
To: main@SDR-Radio.groups.io
Subject: [SDR-Radio] Where do I find Protocol 2 firmware
 
I now have an ANAN 100D.  I downloaded the HPSDR Progammer.  But where
do I find the protocol 2 firmware to load in the 100D?  I would very
much like to run SDRConsole with my 100D.


Carl Moreschi N4PY
58 Hogwood Rd
Louisburg, NC 27549
www.n4py.com
www.n4py.com
N4PY Software is your source for high quality, effective rig control software for your transceiver. N4PY offers rig control software for a wide variety of receivers ...







Where do I find Protocol 2 firmware

Carl Moreschi <n4py3@...>
 

I now have an ANAN 100D. I downloaded the HPSDR Progammer. But where do I find the protocol 2 firmware to load in the 100D? I would very much like to run SDRConsole with my 100D.


Carl Moreschi N4PY
58 Hogwood Rd
Louisburg, NC 27549
www.n4py.com


Wet Weekend in Cornwall

Simon Brown
 

Just received this using the Airspy R2 and NOAA-18.

Going to be 'moist'. ☹

How? See http://sdr-satellites.com/Weather

Simon Brown, G4ELI
www.sdr-radio.com


Re: SDR-Console – v3.0 preview 6, cannot edit "Favorites" data

gautea@...
 

Hi RB.
Sorry for the somehow "round about" answer. As a member of the test team I love to mess around with the Console to better understand what works and what does not :-)
Amazing what you can learn from it. The straight forward procedure for changing the frequency of the favourite is:
1: Change the frequency
2: Change whatever needed settings
3: Click Update
In the Organise you may change the name of the favourite if needed.
If needed you may also add one or more receivers for the favourite from Receive/Add
Beware: The add button in Favourites are for adding a new Favourite.
The yellow star is just indicating a favourite.
A link for the V3 build 845 may be found in a posting from Simon on date july 20. 2017 in this group.
If you like to play with these things without messing up your previous definitions you can do this in an unused Identity. There are 10 of those available.
Good Luck
LB6YD Gaute


Re: SDR-Console – v3.0 preview 6, cannot edit "Favorites" data

rbuck@...
 

Hi GL,

I have build 811 so frequency editing must
not be implemented yet.

Thanks, I am thinking about your answer.
sounds a bit round about but whatever works.

So first create a new file for a new SDR hardware
radio?

What I did:
I just clicked the Favorites tab then "Organize".
That produces a frequency list.
Highlight a frequency, say 40m then click the
"Edit" button.
A new window opens but any editing I perform does not stick.

I assume the yellow stars in the various menu items are default values?

RB
KM6LPW

----- Original Message -----
From: "gautea via Groups.Io" <gautea@...>
To: main@SDR-Radio.groups.io
Sent: Thursday, September 28, 2017 1:27:33 PM
Subject: Re: [SDR-Radio] SDR-Console – v3.0 preview 6, cannot edit "Favorites" data

Hi rbuck. Please attach a screenshot of where you edit the frequency for the Favourite.
That is not possible in my version of V3, Jul 20 2017 build 845.
I have to add a receiver with the new frequency for the Favourite, then untick the previous receiver/frequency before clicking OK in the Organiser.
......or safer to avoid getting a "improper argument..." message, create a new favourite for the new frequency and delete the old one if not needed :-)
GL
LB6YD Gaute


Re: HF+ Questions

Mark Cayton <mcayton@...>
 

Noise floor isn't the only consideration.  Dynamic range is valuable when a weak signal is adjacent to a very strong signal, or when an extremely strong signal would otherwise simply overload a receiver front end.
--
Mark  KF5VQY


Re: HF+ Questions

Brian Morrison
 

On Fri, 29 Sep 2017 14:39:06 +0000
Tony_AD0VC wrote:

Maybe somebody else will comment on the assertion that ADC width
doesn't matter.
Beyond a certain point it doesn't, but you need enough bits to hit the
dynamic range needed, roughly 6dB/bit.

The upper limit is set by the reference voltage the ADC uses, the lower
limit by internal noise and by the size of the LSB. If a 14 bit ADC is
able to give a receiver noise floor that is low enough then a 16 bit
ADC will not make it any lower because other sources of noise become
dominant.

--

Brian Morrison


Re: HF+ Questions

Mark Cayton <mcayton@...>
 
Edited

Tony,

I'm just an idiot (a happy idiot, but an idiot nonetheless) so I don't know how such nebulous processes as quantization and decimation are specifically capable of improving the noise floor (and consequently the MDS and dynamic range) of an ADC, but they are.

I found a thread in the Flex Community forum that speaks obliquely to that end - the Flex engineers stated that they were able to improve the Flex 6300's IMD DR3 figures by anywhere between 7 dB and 16 dB (depending on band and preamp settings) in the latest SmartSDR V2 software release.  They didn't reveal how they were able to do that, declaring that to be a company secret, seeing as how there's a bunch of other folks (and companies) who'd also like to know.  :)

Here's that thread:

https://community.flexradio.com/flexradio/topics/v2-improved-dynamic-range-for-flex-6300?topic-reply-list%5Bsettings%5D%5Bfilter_by%5D=all

73,
Mark  KF5VQY


Re: HF+ Questions

Tony_AD0VC
 

Simon,


Maybe somebody else will comment on the assertion that ADC width doesn't matter. I will leave it at that. Tradeoffs must sometimes be made.


Tony

ad0vc


 








From: main@SDR-Radio.groups.io <main@SDR-Radio.groups.io> on behalf of Simon Brown <simon@...>
Sent: Friday, September 29, 2017 12:17 AM
To: main@SDR-Radio.groups.io
Subject: Re: [SDR-Radio] HF+ Questions
 

OK,

 

  1. 768kHz from the radio, my software also provides 394, 192, 96 and 48kHz
  2. USB only but of course supported by servers including SpyServer
  3. ADC bits doesn’t really matter – MDS and Dynamic Range are the important numbers

 

Simon Brown, G4ELI
www.sdr-radio.com

 

From: main@SDR-Radio.groups.io [mailto:main@SDR-Radio.groups.io] On Behalf Of Tony_AD0VC
Sent: 29 September 2017 03:25
To: main@SDR-Radio.groups.io
Subject: [SDR-Radio] HF+ Questions

 

I looked at the Airspy site and read what they had on the HF+. Some info seems to be missing:

 

  1. What sample rates are supported? All I see mentioned is 768Khz
  2. Can it be connected with USB or is it network only?
  3. How many bits in the ADC? All I see mentioned is an 18 bit DDC which is the down converter. How about the actual sampler?

 

Does anybody know?

 

Tony

ad0vc


Re: HF+ Comparison

Nils Schiffhauer
 

... thanks, Simon, and this IS quite a difference (worthwhile waiting a bit ...)! 73 Nils


Am 28.09.2017 um 21:44 schrieb Simon Brown:

So,

 

Done properly (or at least better) this time: http://sdr-radio.com/AirspyHFPlus

...


Re: V3 RDS

Mike Fallon <homebush@...>
 

OK, thank you


On 29/09/2017 06:56, Simon Brown wrote:

Mike,

Yes, but there's a big list of things to add.

Simon Brown, G4ELI
www.sdr-radio.com

-----Original Message-----
From: main@SDR-Radio.groups.io [mailto:main@SDR-Radio.groups.io] On Behalf Of Mike Fallon via Groups.Io
Sent: 29 September 2017 07:35
To: main@SDR-Radio.groups.io
Subject: [SDR-Radio] V3 RDS

Hi Simon,

Is there any chance that you could implement RDS logging in a future release please?

Many thanks

Mike










Re: V3 RDS

Simon Brown
 

Mike,

Yes, but there's a big list of things to add.

Simon Brown, G4ELI
www.sdr-radio.com

-----Original Message-----
From: main@SDR-Radio.groups.io [mailto:main@SDR-Radio.groups.io] On Behalf Of Mike Fallon via Groups.Io
Sent: 29 September 2017 07:35
To: main@SDR-Radio.groups.io
Subject: [SDR-Radio] V3 RDS

Hi Simon,

Is there any chance that you could implement RDS logging in a future release please?

Many thanks

Mike


V3 RDS

Mike Fallon <homebush@...>
 

Hi Simon,

Is there any chance that you could implement RDS logging in a future release please?

Many thanks

Mike