|
Re: Perseus on USB3 ports. (was Problems with V3 console after 1709 W10 installation)
Simon Brown
Ah,
Interesting. Obviously this should be transparent and part of the driver.
I'll take a look later today...
Simon Brown, G4ELI
www.dxgalaxy.com
www.sdr-radio.com
www.sdr-satellites.com
toggle quoted message
Show quoted text
-----Original Message----- From: main@SDR-Radio.groups.io [mailto:main@SDR-Radio.groups.io] On Behalf Of Leif Asbrink Sent: 03 December 2017 00:35 To: main@SDR-Radio.groups.io Subject: Re: [SDR-Radio] Perseus on USB3 ports. (was Problems with V3 console after 1709 W10 installation) Hi Simon and All, I have found the problem with the new driver for VIA USB3. In Linrad there is an option to set "DMA rate" for the input. Linrad uses that to compute the block size for reading from the input hardware. By setting min DMA size=1000 (Hz) the block size becomes small enough for Perseus to work again under 64 bit Win 10. I will do the appropriate change to the Linrad code to never read too big chunks from the USB3 port. Maybe the same problem exists with other hardware. I will check for it and take appropriate action if I find problems with other USB hardware under 64 bit Win 10. Maybe the same problem exists in SDR-Radio? 73 Leif On Sat, 2 Dec 2017 21:37:46 -0000 "Simon Brown" <simon@...> wrote: Ah,
Now that makes sense - a thread is blocked by the failure to read from
the Perseus. One solution is to use a USB PCIe card which is known to
be good, another option is to buy the Airspy HF+.
Simon Brown, G4ELI
<http://www.dxgalaxy.com/> www.dxgalaxy.com
<http://www.sdr-radio.com/> www.sdr-radio.com
<http://www.sdr-satellites.com> www.sdr-satellites.com
From: main@SDR-Radio.groups.io [mailto:main@SDR-Radio.groups.io] On
Behalf Of chutton12000
Sent: 02 December 2017 20:16
To: main@SDR-Radio.groups.io
Subject: Re: [SDR-Radio] Perseus on USB3 ports. (was Problems with V3
console after 1709 W10 installation)
More info: (and I should have added this before)
The playback fails (hangs up) if the receiver has been started. If the
receiver is not started, I can play back OK.
I believe the USB to the Perseus is OK as the Perseus is configured
properly when the radio is started. It's just that nothing happens
afterwards. The spectrum display never shows anything and there is no audio.
Chuck
_____
From: Chuck Hutton <charlesh3@... <mailto:charlesh3@...> >
Sent: Saturday, December 2, 2017 12:02 PM
To: main@SDR-Radio.groups.io <mailto:main@SDR-Radio.groups.io>
Subject: Re: [SDR-Radio] Perseus on USB3 ports. (was Problems with V3
console after 1709 W10 installation)
Simon -
As mentioned, the hourglass spins forever and the program doesn't respond.
So I assume that there's no way to do the normal SDR Console screen
capture.
Chuck
_____
From: main@SDR-Radio.groups.io <mailto:main@SDR-Radio.groups.io>
<main@SDR-Radio.groups.io <mailto:main@SDR-Radio.groups.io> > on
behalf of Simon Brown <simon@...
<mailto:simon@...> >
Sent: Saturday, December 2, 2017 11:11 AM
To: main@SDR-Radio.groups.io <mailto:main@SDR-Radio.groups.io>
Subject: Re: [SDR-Radio] Perseus on USB3 ports. (was Problems with V3
console after 1709 W10 installation)
Chuck,
You threw me with the Perseus reference. If you can't play files then
yes, it's borked. There's a reset option, also you can post a screenshot.
Simon Brown, G4ELI
<https://eur01.safelinks.protection.outlook.com/?url=http%3A%2F%2Fwww.
dxgala
xy.com%2F&data=02%7C01%7Ccharlesh3%40msn.com%7Cb337e754b2054b14e6f808d
539b87
cf5%7C84df9e7fe9f640afb435aaaaaaaaaaaa%7C1%7C0%7C636478386886666272&sd
ata=8h psTcmd3nayE2Zs614T5vR0cVhaqgwXSWBSRfdzHDE%3D&reserved=0>
www.dxgalaxy.com
<https://eur01.safelinks.protection.outlook.com/?url=http%3A%2F%2Fwww.
sdr-ra
dio.com%2F&data=02%7C01%7Ccharlesh3%40msn.com%7Cb337e754b2054b14e6f808
d539b8
7cf5%7C84df9e7fe9f640afb435aaaaaaaaaaaa%7C1%7C0%7C636478386886666272&s
data=W May9carm%2BlETLxZKwFkwvHsZUXzRDF%2B8cIv79KrOHE%3D&reserved=0>
www.sdr-radio.com
<https://eur01.safelinks.protection.outlook.com/?url=http%3A%2F%2Fwww.
sdr-sa
tellites.com&data=02%7C01%7Ccharlesh3%40msn.com%7Cb337e754b2054b14e6f8
08d539
b87cf5%7C84df9e7fe9f640afb435aaaaaaaaaaaa%7C1%7C0%7C636478386886666272
&sdata =nPQiXIEelIwtLhefJknsrfexiyqkk3XAERe2bZN1MgE%3D&reserved=0>
www.sdr-satellites.com
From: main@SDR-Radio.groups.io <mailto:main@SDR-Radio.groups.io>
[mailto:main@SDR-Radio.groups.io] On Behalf Of chutton12000
Sent: 02 December 2017 18:41
To: main@SDR-Radio.groups.io <mailto:main@SDR-Radio.groups.io>
Subject: Re: [SDR-Radio] Perseus on USB3 ports. (was Problems with V3
console after 1709 W10 installation)
Hi Simon -
I;m aware of the info at your link but....
(1) USB issues shouldn't affect playback of previously recorded files.
(2) SDR Console worked OK with my Perseus in 2015-2016-early 2017.
Does adding the Perseus definition and having it accepted mean that
Console found the Perseus?
Chuck
_____
From: main@SDR-Radio.groups.io <mailto:main@SDR-Radio.groups.io>
<main@SDR-Radio.groups.io <mailto:main@SDR-Radio.groups.io> > on
behalf of Simon Brown <simon@...
<mailto:simon@...> >
Sent: Friday, December 1, 2017 11:22 PM
To: main@SDR-Radio.groups.io <mailto:main@SDR-Radio.groups.io>
Subject: Re: [SDR-Radio] Perseus on USB3 ports. (was Problems with V3
console after 1709 W10 installation)
Chuck,
Everything I know about Perseus is on the website
http://www.sdr-radio.com/Radios/Perseus
<https://nam04.safelinks.protection.outlook.com/?url=http%3A%2F%2Fwww.
sdr-ra
dio.com%2FRadios%2FPerseus&data=02%7C01%7Ccharlesh3%40msn.com%7Ce25b2e
4133f2
4a48334908d53955883e%7C84df9e7fe9f640afb435aaaaaaaaaaaa%7C1%7C0%7C6364
779618
67263252&sdata=uu3fLv%2FBuH99wCklXLNGFDx6Lj5kZIV6tGXXExpE3jA%3D&reserv
ed=0>
.
Simon Brown, G4ELI
<https://nam04.safelinks.protection.outlook.com/?url=http%3A%2F%2Fwww.
dxgala
xy.com%2F&data=02%7C01%7Ccharlesh3%40msn.com%7Ce25b2e4133f24a48334908d
539558
83e%7C84df9e7fe9f640afb435aaaaaaaaaaaa%7C1%7C0%7C636477961867263252&sd
ata=kz sYef8NWMFf2D0ajYcPRocin50mlxQNIG%2F%2BP0bVh%2FA%3D&reserved=0>
www.dxgalaxy.com
<https://nam04.safelinks.protection.outlook.com/?url=http%3A%2F%2Fwww.
sdr-ra
dio.com%2F&data=02%7C01%7Ccharlesh3%40msn.com%7Ce25b2e4133f24a48334908
d53955
883e%7C84df9e7fe9f640afb435aaaaaaaaaaaa%7C1%7C0%7C636477961867263252&s
data=A lVDKqqXLIl8Bfx7LHjJgnE6oJjq04K7pn%2B3UqgTwRE%3D&reserved=0>
www.sdr-radio.com
<https://nam04.safelinks.protection.outlook.com/?url=http%3A%2F%2Fwww.
sdr-sa
tellites.com&data=02%7C01%7Ccharlesh3%40msn.com%7Ce25b2e4133f24a483349
08d539
55883e%7C84df9e7fe9f640afb435aaaaaaaaaaaa%7C1%7C0%7C636477961867263252
&sdata =wBsuxRlwMyrNRDq5HCCc3Xh8nMz%2Fo3MhCCfOiwyt8VE%3D&reserved=0>
www.sdr-satellites.com
From: main@SDR-Radio.groups.io <mailto:main@SDR-Radio.groups.io>
[mailto:main@SDR-Radio.groups.io] On Behalf Of chutton12000
Sent: 02 December 2017 01:28
To: main@SDR-Radio.groups.io <mailto:main@SDR-Radio.groups.io>
Subject: Re: [SDR-Radio] Perseus on USB3 ports. (was Problems with V3
console after 1709 W10 installation)
Here is a problem that may or may not have a common root. On my Win
10 x64 machine with 1709 uodates -
all ports (USB2 and 3) work with the native Perseus software ver 4.1.
I have the signed USB drivers installed, as supplied on the Microtelecom
site.
With the same machine and using either the USB2 or the USB3 ports, SDR
Console sees the Perseus when I add it but nothing happens when I
start the radio and attempt to listen live. The hourglass just spins
forever. The same thing happens when I try to play back a previously
recorded Perseus file.
SDR Console used to run perfectly on this machine, but I had not tried
it in perhaps 8 months so don't really know when it broke.
Chuck
_____
From: main@SDR-Radio.groups.io <mailto:main@SDR-Radio.groups.io>
<main@SDR-Radio.groups.io <mailto:main@SDR-Radio.groups.io> > on
behalf of Leif Asbrink <leif@... <mailto:leif@...> >
Sent: Friday, December 1, 2017 4:31 PM
To: main@SDR-Radio.groups.io <mailto:main@SDR-Radio.groups.io>
Subject: Re: [SDR-Radio] Perseus on USB3 ports. (was Problems with V3
console after 1709 W10 installation)
Hello Simon,
A couple of days ago I verified that the dll works fine on all USB3
ports of my i7 computer under 64 bit Win 10. That was with a system
updated until April 2016.
Today I updated my 64 bit Win 10 to the very latest and I find that
Linrad no longer works on the USB3 ports having VIA USB3 eXtensible
Host Controller.
The driver date is 2017-09-28. Neither the 32 bit, nor the 64 bit
version works, but the Renesas ports still work fine although they
also have a new drive routine.
I have not found any way to install the previous driver for VIA.
An interesting thing is that perseus.exe works fine with the new VIA
driver. Both perseus v4.1 which uses perseususb.dll and perseus.exe v5
which does not use perseususb.dll.
It is obvious that I am doing something wrong in Linrad, I will have a
look at it to see if I can get Linrad going with the latest Microsoft
driver for VIA.
Question: Is there anyone who can not get perseus.exe running on USB3
ports? I now know I have a USB3 problem with Linrad - maybe I will be
able to fix it, but I do not expect Linrad to work on systems where
perseus.exe
v5 does not run on USB3 ports.
73
Leif
Thanks Leif.
The driver works with some USB3 hardware but not all.
Simon Brown, G4ELI
https://eur02.safelinks.protection.outlook.com/?url=www.dxgalaxy.com <https://eur02.safelinks.protection.outlook.com/?url=www.dxgalaxy.com&
data=0
2%7C01%7Ccharlesh3%40msn.com%7C94e296aeab4d46e9585008d5391c08ba%7C84df
9e7fe9
f640afb435aaaaaaaaaaaa%7C1%7C0%7C636477714917915558&sdata=r8ms4Po2NxmU
UhobQB OeZRLR7ay4zvZAmIhhDQoBobQ%3D&reserved=0>
&data=02%7C01%7Ccharlesh3%40msn.com%7C94e296aeab4d46e9585008d5391c08ba
%7C84d
f9e7fe9f640afb435aaaaaaaaaaaa%7C1%7C0%7C636477714917915558&sdata=r8ms4
Po2Nxm
UUhobQBOeZRLR7ay4zvZAmIhhDQoBobQ%3D&reserved=0
https://eur02.safelinks.protection.outlook.com/?url=www.sdr-radio.co
m <https://eur02.safelinks.protection.outlook.com/?url=www.sdr-radio.com
&data=
02%7C01%7Ccharlesh3%40msn.com%7C94e296aeab4d46e9585008d5391c08ba%7C84d
f9e7fe
9f640afb435aaaaaaaaaaaa%7C1%7C0%7C636477714917915558&sdata=4PzrWMgOF2s
pBjq9w aSUCVfgwtEGXX5IC7rHrFEYOzE%3D&reserved=0>
&data=02%7C01%7Ccharlesh3%40msn.com%7C94e296aeab4d46e9585008d5391c08ba
%7C84d
f9e7fe9f640afb435aaaaaaaaaaaa%7C1%7C0%7C636477714917915558&sdata=4PzrW
MgOF2s
pBjq9waSUCVfgwtEGXX5IC7rHrFEYOzE%3D&reserved=0
https://eur02.safelinks.protection.outlook.com/?url=www.sdr-satellit
es.com <https://eur02.safelinks.protection.outlook.com/?url=www.sdr-satellite
s.com&
data=02%7C01%7Ccharlesh3%40msn.com%7C94e296aeab4d46e9585008d5391c08ba%
7C84df
9e7fe9f640afb435aaaaaaaaaaaa%7C1%7C0%7C636477714917915558&sdata=iFC3Oo
oOhIgz G%2FwGquDP9VQWIt6H7tbCUzeaKeEcBrk%3D&reserved=0>
&data=02%7C01%7Ccharlesh3%40msn.com%7C94e296aeab4d46e9585008d5391c08ba
%7C84d
f9e7fe9f640afb435aaaaaaaaaaaa%7C1%7C0%7C636477714917915558&sdata=iFC3O
ooOhIg
zG%2FwGquDP9VQWIt6H7tbCUzeaKeEcBrk%3D&reserved=0
-----Original Message-----
From: main@SDR-Radio.groups.io <mailto:main@SDR-Radio.groups.io>
[mailto:main@SDR-Radio.groups.io] On Behalf
Of Leif Asbrink
Sent: 01 December 2017 00:34
To: main@SDR-Radio.groups.io <mailto:main@SDR-Radio.groups.io>
Subject: Re: [SDR-Radio] Problems with V3 console after 1709 W10
installation
Hi Simon,
I do not know from where I got it. If you run the installer here
https://eur02.safelinks.protection.outlook.com/?url=http%3A%2F%2Fsm5bs
z.com%
2Fdll.htm
<https://eur02.safelinks.protection.outlook.com/?url=http%3A%2F%2Fsm5b
sz.com
%2Fdll.htm&data=02%7C01%7Ccharlesh3%40msn.com%7C94e296aeab4d46e9585008
d5391c
08ba%7C84df9e7fe9f640afb435aaaaaaaaaaaa%7C1%7C0%7C636477714917915558&s
data=m LbZVIZB0vuP5CHuJIq7ABT31kn9CcAgL4oJnLrUkzI%3D&reserved=0>
&data=02%7C01%7Ccharlesh3%40msn.com%7C94e296aeab4d46e9585008d5391c08ba
%7C84d
f9e7fe9f640afb435aaaaaaaaaaaa%7C1%7C0%7C636477714917915558&sdata=mLbZV
IZB0vu
P5CHuJIq7ABT31kn9CcAgL4oJnLrUkzI%3D&reserved=0 you will find it in
C:\linrad\dll\x64
Size 126464 bytes. I do not remember from where I got it. I have
attached the output from listdll64.exe
Ihave now verified also on 64 bit Windows 10. I have motherboard
USB2 and USB3 as well a PCIe card with USB3. All works well.
The Win 10 installation I tested was not updated since maybe April
2016. I now updated Win10 to the latest version - and also the 32
bit Win 10 installation I have on the same computer. As a result I
can no longer boot into the 64 bit system. Microsoft has written
something to the 64 bit installation that directs boots to the 32
bit installation:-(
This will take some time to repair - and I am afraid I will have to
repair also Win 7 installations on the system (Four of them. Home
and Ultimate 32 and 64 bit.
Home allows only one CPU while Ultimate allows two.)
Lesson learned: Do never upgrade Win 10 again on a multiboot system.
I do not know if Microsoft would update the USB drivers and cause
the perseususb to no longer work, but it does work well in the April
2016 system.
73
Leif
Leif,
Which Perseus 64-bit driver do you have?
Simon Brown, G4ELI
https://eur02.safelinks.protection.outlook.com/?url=www.dxgalaxy.c
om
<https://eur02.safelinks.protection.outlook.com/?url=www.dxgalaxy.com&
data=0
2%7C01%7Ccharlesh3%40msn.com%7C94e296aeab4d46e9585008d5391c08ba%7C84df
9e7fe9
f640afb435aaaaaaaaaaaa%7C1%7C0%7C636477714917915558&sdata=r8ms4Po2NxmU
UhobQB OeZRLR7ay4zvZAmIhhDQoBobQ%3D&reserved=0>
&data=02%7C01%7Ccharlesh3%40msn.com%7C94e296aeab4d46e9585008d5391c08ba
%7C84d
f9e7fe9f640afb435aaaaaaaaaaaa%7C1%7C0%7C636477714917915558&sdata=r8ms4
Po2Nxm
UUhobQBOeZRLR7ay4zvZAmIhhDQoBobQ%3D&reserved=0
https://eur02.safelinks.protection.outlook.com/?url=www.sdr-radio.
com
<https://eur02.safelinks.protection.outlook.com/?url=www.sdr-radio.com
&data=
02%7C01%7Ccharlesh3%40msn.com%7C94e296aeab4d46e9585008d5391c08ba%7C84d
f9e7fe
9f640afb435aaaaaaaaaaaa%7C1%7C0%7C636477714917915558&sdata=4PzrWMgOF2s
pBjq9w aSUCVfgwtEGXX5IC7rHrFEYOzE%3D&reserved=0>
&data=02%7C01%7Ccharlesh3%40msn.com%7C94e296aeab4d46e9585008d5391c08ba
%7C84d
f9e7fe9f640afb435aaaaaaaaaaaa%7C1%7C0%7C636477714917915558&sdata=4PzrW
MgOF2s
pBjq9waSUCVfgwtEGXX5IC7rHrFEYOzE%3D&reserved=0
https://eur02.safelinks.protection.outlook.com/?url=www.sdr-satellites
.com
<https://eur02.safelinks.protection.outlook.com/?url=www.sdr-satellite
s.com&
data=02%7C01%7Ccharlesh3%40msn.com%7C94e296aeab4d46e9585008d5391c08ba%
7C84df
9e7fe9f640afb435aaaaaaaaaaaa%7C1%7C0%7C636477714917915558&sdata=iFC3Oo
oOhIgz G%2FwGquDP9VQWIt6H7tbCUzeaKeEcBrk%3D&reserved=0>
&data=02%7C01%7Ccharlesh3%40msn.com%7C94e296aeab4d46e9585008d5391c08ba
%7C84d
f9e7fe9f640afb435aaaaaaaaaaaa%7C1%7C0%7C636477714917915558&sdata=iFC3O
ooOhIg
zG%2FwGquDP9VQWIt6H7tbCUzeaKeEcBrk%3D&reserved=0
-----Original Message-----
From: main@SDR-Radio.groups.io <mailto:main@SDR-Radio.groups.io>
[mailto:main@SDR-Radio.groups.io] On Behalf
Of Leif Asbrink
Well, I had some problems in the past, but today, with the latest
drive routines for the USB system I have no problem on any
USB3 port on any of my computers.
I would be interested to know if you would have any problem
running Perseus
with Linrad on a "problematic" USB port.
If you think it would be difficult I would make an install video
showing the
very few commands you need. Just tell me what OS you are using.
73
Leif
|
|
|
Re: Perseus on USB3 ports. (was Problems with V3 console after 1709 W10 installation)
Hi Simon and All, I have found the problem with the new driver for VIA USB3. In Linrad there is an option to set "DMA rate" for the input. Linrad uses that to compute the block size for reading from the input hardware. By setting min DMA size=1000 (Hz) the block size becomes small enough for Perseus to work again under 64 bit Win 10. I will do the appropriate change to the Linrad code to never read too big chunks from the USB3 port. Maybe the same problem exists with other hardware. I will check for it and take appropriate action if I find problems with other USB hardware under 64 bit Win 10. Maybe the same problem exists in SDR-Radio? 73 Leif On Sat, 2 Dec 2017 21:37:46 -0000 "Simon Brown" <simon@...> wrote: Ah,
Now that makes sense - a thread is blocked by the failure to read from the
Perseus. One solution is to use a USB PCIe card which is known to be good,
another option is to buy the Airspy HF+.
Simon Brown, G4ELI
<http://www.dxgalaxy.com/> www.dxgalaxy.com
<http://www.sdr-radio.com/> www.sdr-radio.com
<http://www.sdr-satellites.com> www.sdr-satellites.com
From: main@SDR-Radio.groups.io [mailto:main@SDR-Radio.groups.io] On Behalf
Of chutton12000
Sent: 02 December 2017 20:16
To: main@SDR-Radio.groups.io
Subject: Re: [SDR-Radio] Perseus on USB3 ports. (was Problems with V3
console after 1709 W10 installation)
More info: (and I should have added this before)
The playback fails (hangs up) if the receiver has been started. If the
receiver is not started, I can play back OK.
I believe the USB to the Perseus is OK as the Perseus is configured properly
when the radio is started. It's just that nothing happens afterwards. The
spectrum display never shows anything and there is no audio.
Chuck
_____
From: Chuck Hutton <charlesh3@... <mailto:charlesh3@...> >
Sent: Saturday, December 2, 2017 12:02 PM
To: main@SDR-Radio.groups.io <mailto:main@SDR-Radio.groups.io>
Subject: Re: [SDR-Radio] Perseus on USB3 ports. (was Problems with V3
console after 1709 W10 installation)
Simon -
As mentioned, the hourglass spins forever and the program doesn't respond.
So I assume that there's no way to do the normal SDR Console screen capture.
Chuck
_____
From: main@SDR-Radio.groups.io <mailto:main@SDR-Radio.groups.io>
<main@SDR-Radio.groups.io <mailto:main@SDR-Radio.groups.io> > on behalf of
Simon Brown <simon@... <mailto:simon@...> >
Sent: Saturday, December 2, 2017 11:11 AM
To: main@SDR-Radio.groups.io <mailto:main@SDR-Radio.groups.io>
Subject: Re: [SDR-Radio] Perseus on USB3 ports. (was Problems with V3
console after 1709 W10 installation)
Chuck,
You threw me with the Perseus reference. If you can't play files then yes,
it's borked. There's a reset option, also you can post a screenshot.
Simon Brown, G4ELI
<https://eur01.safelinks.protection.outlook.com/?url=http%3A%2F%2Fwww.dxgala
xy.com%2F&data=02%7C01%7Ccharlesh3%40msn.com%7Cb337e754b2054b14e6f808d539b87
cf5%7C84df9e7fe9f640afb435aaaaaaaaaaaa%7C1%7C0%7C636478386886666272&sdata=8h
psTcmd3nayE2Zs614T5vR0cVhaqgwXSWBSRfdzHDE%3D&reserved=0> www.dxgalaxy.com
<https://eur01.safelinks.protection.outlook.com/?url=http%3A%2F%2Fwww.sdr-ra
dio.com%2F&data=02%7C01%7Ccharlesh3%40msn.com%7Cb337e754b2054b14e6f808d539b8
7cf5%7C84df9e7fe9f640afb435aaaaaaaaaaaa%7C1%7C0%7C636478386886666272&sdata=W
May9carm%2BlETLxZKwFkwvHsZUXzRDF%2B8cIv79KrOHE%3D&reserved=0>
www.sdr-radio.com
<https://eur01.safelinks.protection.outlook.com/?url=http%3A%2F%2Fwww.sdr-sa
tellites.com&data=02%7C01%7Ccharlesh3%40msn.com%7Cb337e754b2054b14e6f808d539
b87cf5%7C84df9e7fe9f640afb435aaaaaaaaaaaa%7C1%7C0%7C636478386886666272&sdata
=nPQiXIEelIwtLhefJknsrfexiyqkk3XAERe2bZN1MgE%3D&reserved=0>
www.sdr-satellites.com
From: main@SDR-Radio.groups.io <mailto:main@SDR-Radio.groups.io>
[mailto:main@SDR-Radio.groups.io] On Behalf Of chutton12000
Sent: 02 December 2017 18:41
To: main@SDR-Radio.groups.io <mailto:main@SDR-Radio.groups.io>
Subject: Re: [SDR-Radio] Perseus on USB3 ports. (was Problems with V3
console after 1709 W10 installation)
Hi Simon -
I;m aware of the info at your link but....
(1) USB issues shouldn't affect playback of previously recorded files.
(2) SDR Console worked OK with my Perseus in 2015-2016-early 2017.
Does adding the Perseus definition and having it accepted mean that Console
found the Perseus?
Chuck
_____
From: main@SDR-Radio.groups.io <mailto:main@SDR-Radio.groups.io>
<main@SDR-Radio.groups.io <mailto:main@SDR-Radio.groups.io> > on behalf of
Simon Brown <simon@... <mailto:simon@...> >
Sent: Friday, December 1, 2017 11:22 PM
To: main@SDR-Radio.groups.io <mailto:main@SDR-Radio.groups.io>
Subject: Re: [SDR-Radio] Perseus on USB3 ports. (was Problems with V3
console after 1709 W10 installation)
Chuck,
Everything I know about Perseus is on the website
http://www.sdr-radio.com/Radios/Perseus
<https://nam04.safelinks.protection.outlook.com/?url=http%3A%2F%2Fwww.sdr-ra
dio.com%2FRadios%2FPerseus&data=02%7C01%7Ccharlesh3%40msn.com%7Ce25b2e4133f2
4a48334908d53955883e%7C84df9e7fe9f640afb435aaaaaaaaaaaa%7C1%7C0%7C6364779618
67263252&sdata=uu3fLv%2FBuH99wCklXLNGFDx6Lj5kZIV6tGXXExpE3jA%3D&reserved=0>
.
Simon Brown, G4ELI
<https://nam04.safelinks.protection.outlook.com/?url=http%3A%2F%2Fwww.dxgala
xy.com%2F&data=02%7C01%7Ccharlesh3%40msn.com%7Ce25b2e4133f24a48334908d539558
83e%7C84df9e7fe9f640afb435aaaaaaaaaaaa%7C1%7C0%7C636477961867263252&sdata=kz
sYef8NWMFf2D0ajYcPRocin50mlxQNIG%2F%2BP0bVh%2FA%3D&reserved=0>
www.dxgalaxy.com
<https://nam04.safelinks.protection.outlook.com/?url=http%3A%2F%2Fwww.sdr-ra
dio.com%2F&data=02%7C01%7Ccharlesh3%40msn.com%7Ce25b2e4133f24a48334908d53955
883e%7C84df9e7fe9f640afb435aaaaaaaaaaaa%7C1%7C0%7C636477961867263252&sdata=A
lVDKqqXLIl8Bfx7LHjJgnE6oJjq04K7pn%2B3UqgTwRE%3D&reserved=0>
www.sdr-radio.com
<https://nam04.safelinks.protection.outlook.com/?url=http%3A%2F%2Fwww.sdr-sa
tellites.com&data=02%7C01%7Ccharlesh3%40msn.com%7Ce25b2e4133f24a48334908d539
55883e%7C84df9e7fe9f640afb435aaaaaaaaaaaa%7C1%7C0%7C636477961867263252&sdata
=wBsuxRlwMyrNRDq5HCCc3Xh8nMz%2Fo3MhCCfOiwyt8VE%3D&reserved=0>
www.sdr-satellites.com
From: main@SDR-Radio.groups.io <mailto:main@SDR-Radio.groups.io>
[mailto:main@SDR-Radio.groups.io] On Behalf Of chutton12000
Sent: 02 December 2017 01:28
To: main@SDR-Radio.groups.io <mailto:main@SDR-Radio.groups.io>
Subject: Re: [SDR-Radio] Perseus on USB3 ports. (was Problems with V3
console after 1709 W10 installation)
Here is a problem that may or may not have a common root. On my Win 10 x64
machine with 1709 uodates -
all ports (USB2 and 3) work with the native Perseus software ver 4.1. I have
the signed USB drivers installed, as supplied on the Microtelecom site.
With the same machine and using either the USB2 or the USB3 ports, SDR
Console sees the Perseus when I add it but nothing happens when I start the
radio and attempt to listen live. The hourglass just spins forever. The same
thing happens when I try to play back a previously recorded Perseus file.
SDR Console used to run perfectly on this machine, but I had not tried it in
perhaps 8 months so don't really know when it broke.
Chuck
_____
From: main@SDR-Radio.groups.io <mailto:main@SDR-Radio.groups.io>
<main@SDR-Radio.groups.io <mailto:main@SDR-Radio.groups.io> > on behalf of
Leif Asbrink <leif@... <mailto:leif@...> >
Sent: Friday, December 1, 2017 4:31 PM
To: main@SDR-Radio.groups.io <mailto:main@SDR-Radio.groups.io>
Subject: Re: [SDR-Radio] Perseus on USB3 ports. (was Problems with V3
console after 1709 W10 installation)
Hello Simon,
A couple of days ago I verified that the dll works
fine on all USB3 ports of my i7 computer under 64 bit
Win 10. That was with a system updated until April 2016.
Today I updated my 64 bit Win 10 to the very latest
and I find that Linrad no longer works on the USB3
ports having VIA USB3 eXtensible Host Controller.
The driver date is 2017-09-28. Neither the 32 bit,
nor the 64 bit version works, but the Renesas ports
still work fine although they also have a new drive
routine.
I have not found any way to install the previous driver
for VIA.
An interesting thing is that perseus.exe works fine
with the new VIA driver. Both perseus v4.1 which uses
perseususb.dll and perseus.exe v5 which does not use
perseususb.dll.
It is obvious that I am doing something wrong in Linrad,
I will have a look at it to see if I can get Linrad going
with the latest Microsoft driver for VIA.
Question: Is there anyone who can not get perseus.exe
running on USB3 ports? I now know I have a USB3 problem
with Linrad - maybe I will be able to fix it, but I
do not expect Linrad to work on systems where perseus.exe
v5 does not run on USB3 ports.
73
Leif
Thanks Leif.
The driver works with some USB3 hardware but not all.
Simon Brown, G4ELI
https://eur02.safelinks.protection.outlook.com/?url=www.dxgalaxy.com <https://eur02.safelinks.protection.outlook.com/?url=www.dxgalaxy.com&data=0
2%7C01%7Ccharlesh3%40msn.com%7C94e296aeab4d46e9585008d5391c08ba%7C84df9e7fe9
f640afb435aaaaaaaaaaaa%7C1%7C0%7C636477714917915558&sdata=r8ms4Po2NxmUUhobQB
OeZRLR7ay4zvZAmIhhDQoBobQ%3D&reserved=0>
&data=02%7C01%7Ccharlesh3%40msn.com%7C94e296aeab4d46e9585008d5391c08ba%7C84d
f9e7fe9f640afb435aaaaaaaaaaaa%7C1%7C0%7C636477714917915558&sdata=r8ms4Po2Nxm
UUhobQBOeZRLR7ay4zvZAmIhhDQoBobQ%3D&reserved=0
https://eur02.safelinks.protection.outlook.com/?url=www.sdr-radio.com <https://eur02.safelinks.protection.outlook.com/?url=www.sdr-radio.com&data=
02%7C01%7Ccharlesh3%40msn.com%7C94e296aeab4d46e9585008d5391c08ba%7C84df9e7fe
9f640afb435aaaaaaaaaaaa%7C1%7C0%7C636477714917915558&sdata=4PzrWMgOF2spBjq9w
aSUCVfgwtEGXX5IC7rHrFEYOzE%3D&reserved=0>
&data=02%7C01%7Ccharlesh3%40msn.com%7C94e296aeab4d46e9585008d5391c08ba%7C84d
f9e7fe9f640afb435aaaaaaaaaaaa%7C1%7C0%7C636477714917915558&sdata=4PzrWMgOF2s
pBjq9waSUCVfgwtEGXX5IC7rHrFEYOzE%3D&reserved=0
https://eur02.safelinks.protection.outlook.com/?url=www.sdr-satellites.com <https://eur02.safelinks.protection.outlook.com/?url=www.sdr-satellites.com&
data=02%7C01%7Ccharlesh3%40msn.com%7C94e296aeab4d46e9585008d5391c08ba%7C84df
9e7fe9f640afb435aaaaaaaaaaaa%7C1%7C0%7C636477714917915558&sdata=iFC3OooOhIgz
G%2FwGquDP9VQWIt6H7tbCUzeaKeEcBrk%3D&reserved=0>
&data=02%7C01%7Ccharlesh3%40msn.com%7C94e296aeab4d46e9585008d5391c08ba%7C84d
f9e7fe9f640afb435aaaaaaaaaaaa%7C1%7C0%7C636477714917915558&sdata=iFC3OooOhIg
zG%2FwGquDP9VQWIt6H7tbCUzeaKeEcBrk%3D&reserved=0
-----Original Message-----
From: main@SDR-Radio.groups.io <mailto:main@SDR-Radio.groups.io>
[mailto:main@SDR-Radio.groups.io] On Behalf
Of Leif Asbrink
Sent: 01 December 2017 00:34
To: main@SDR-Radio.groups.io <mailto:main@SDR-Radio.groups.io>
Subject: Re: [SDR-Radio] Problems with V3 console after 1709 W10
installation
Hi Simon,
I do not know from where I got it. If you run the installer here
https://eur02.safelinks.protection.outlook.com/?url=http%3A%2F%2Fsm5bsz.com%
2Fdll.htm
<https://eur02.safelinks.protection.outlook.com/?url=http%3A%2F%2Fsm5bsz.com
%2Fdll.htm&data=02%7C01%7Ccharlesh3%40msn.com%7C94e296aeab4d46e9585008d5391c
08ba%7C84df9e7fe9f640afb435aaaaaaaaaaaa%7C1%7C0%7C636477714917915558&sdata=m
LbZVIZB0vuP5CHuJIq7ABT31kn9CcAgL4oJnLrUkzI%3D&reserved=0>
&data=02%7C01%7Ccharlesh3%40msn.com%7C94e296aeab4d46e9585008d5391c08ba%7C84d
f9e7fe9f640afb435aaaaaaaaaaaa%7C1%7C0%7C636477714917915558&sdata=mLbZVIZB0vu
P5CHuJIq7ABT31kn9CcAgL4oJnLrUkzI%3D&reserved=0 you will find it in
C:\linrad\dll\x64
Size 126464 bytes. I do not remember from where I got it. I have attached
the output from listdll64.exe
Ihave now verified also on 64 bit Windows 10. I have
motherboard USB2 and USB3 as well a PCIe card with
USB3. All works well.
The Win 10 installation I tested was not updated since
maybe April 2016. I now updated Win10 to the latest
version - and also the 32 bit Win 10 installation I
have on the same computer. As a result I can no longer
boot into the 64 bit system. Microsoft has written
something to the 64 bit installation that directs boots
to the 32 bit installation:-(
This will take some time to repair - and I am afraid I
will have to repair also Win 7 installations on the
system (Four of them. Home and Ultimate 32 and 64 bit.
Home allows only one CPU while Ultimate allows two.)
Lesson learned: Do never upgrade Win 10 again on a multiboot
system.
I do not know if Microsoft would update the USB drivers
and cause the perseususb to no longer work, but it does
work well in the April 2016 system.
73
Leif
Leif,
Which Perseus 64-bit driver do you have?
Simon Brown, G4ELI
https://eur02.safelinks.protection.outlook.com/?url=www.dxgalaxy.com
<https://eur02.safelinks.protection.outlook.com/?url=www.dxgalaxy.com&data=0
2%7C01%7Ccharlesh3%40msn.com%7C94e296aeab4d46e9585008d5391c08ba%7C84df9e7fe9
f640afb435aaaaaaaaaaaa%7C1%7C0%7C636477714917915558&sdata=r8ms4Po2NxmUUhobQB
OeZRLR7ay4zvZAmIhhDQoBobQ%3D&reserved=0>
&data=02%7C01%7Ccharlesh3%40msn.com%7C94e296aeab4d46e9585008d5391c08ba%7C84d
f9e7fe9f640afb435aaaaaaaaaaaa%7C1%7C0%7C636477714917915558&sdata=r8ms4Po2Nxm
UUhobQBOeZRLR7ay4zvZAmIhhDQoBobQ%3D&reserved=0
https://eur02.safelinks.protection.outlook.com/?url=www.sdr-radio.com
<https://eur02.safelinks.protection.outlook.com/?url=www.sdr-radio.com&data=
02%7C01%7Ccharlesh3%40msn.com%7C94e296aeab4d46e9585008d5391c08ba%7C84df9e7fe
9f640afb435aaaaaaaaaaaa%7C1%7C0%7C636477714917915558&sdata=4PzrWMgOF2spBjq9w
aSUCVfgwtEGXX5IC7rHrFEYOzE%3D&reserved=0>
&data=02%7C01%7Ccharlesh3%40msn.com%7C94e296aeab4d46e9585008d5391c08ba%7C84d
f9e7fe9f640afb435aaaaaaaaaaaa%7C1%7C0%7C636477714917915558&sdata=4PzrWMgOF2s
pBjq9waSUCVfgwtEGXX5IC7rHrFEYOzE%3D&reserved=0
https://eur02.safelinks.protection.outlook.com/?url=www.sdr-satellites.com
<https://eur02.safelinks.protection.outlook.com/?url=www.sdr-satellites.com&
data=02%7C01%7Ccharlesh3%40msn.com%7C94e296aeab4d46e9585008d5391c08ba%7C84df
9e7fe9f640afb435aaaaaaaaaaaa%7C1%7C0%7C636477714917915558&sdata=iFC3OooOhIgz
G%2FwGquDP9VQWIt6H7tbCUzeaKeEcBrk%3D&reserved=0>
&data=02%7C01%7Ccharlesh3%40msn.com%7C94e296aeab4d46e9585008d5391c08ba%7C84d
f9e7fe9f640afb435aaaaaaaaaaaa%7C1%7C0%7C636477714917915558&sdata=iFC3OooOhIg
zG%2FwGquDP9VQWIt6H7tbCUzeaKeEcBrk%3D&reserved=0
-----Original Message-----
From: main@SDR-Radio.groups.io <mailto:main@SDR-Radio.groups.io>
[mailto:main@SDR-Radio.groups.io] On Behalf
Of Leif Asbrink
Well, I had some problems in the past, but today, with the latest drive
routines for the USB system I have no problem on any
USB3 port on any of my computers.
I would be interested to know if you would have any problem running Perseus
with Linrad on a "problematic" USB port.
If you think it would be difficult I would make an install video showing the
very few commands you need. Just tell me what OS you are using.
73
Leif
|
|
|
Re: Perseus on USB3 ports. (was Problems with V3 console after 1709 W10 installation)
Simon Brown
Ah, Now that makes sense – a thread is blocked by the failure to read from the Perseus. One solution is to use a USB PCIe card which is known to be good, another option is to buy the Airspy HF+.
From: main@SDR-Radio.groups.io [mailto:main@SDR-Radio.groups.io] On Behalf Of chutton12000
Sent: 02 December 2017 20:16
To: main@SDR-Radio.groups.io
Subject: Re: [SDR-Radio] Perseus on USB3 ports. (was Problems with V3 console after 1709 W10 installation) More info: (and I should have added this before) The playback fails (hangs up) if the receiver has been started. If the receiver is not started, I can play back OK. I believe the USB to the Perseus is OK as the Perseus is configured properly when the radio is started. It's just that nothing happens afterwards. The spectrum display never shows anything and there is no audio. Chuck
From: Chuck Hutton <charlesh3@...>
Sent: Saturday, December 2, 2017 12:02 PM
To: main@SDR-Radio.groups.io
Subject: Re: [SDR-Radio] Perseus on USB3 ports. (was Problems with V3 console after 1709 W10 installation) Simon - As mentioned, the hourglass spins forever and the program doesn't respond. So I assume that there's no way to do the normal SDR Console screen capture. Chuck
Chuck, You threw me with the Perseus reference. If you can’t play files then yes, it’s borked. There’s a reset option, also you can post a screenshot. Hi Simon - I;m aware of the info at your link but.... (1) USB issues shouldn't affect playback of previously recorded files. (2) SDR Console worked OK with my Perseus in 2015-2016-early 2017. Does adding the Perseus definition and having it accepted mean that Console found the Perseus?
Chuck, Everything I know about Perseus is on the website http://www.sdr-radio.com/Radios/Perseus . Here is a problem that may or may not have a common root. On my Win 10 x64 machine with 1709 uodates - all ports (USB2 and 3) work with the native Perseus software ver 4.1. I have the signed USB drivers installed, as supplied on the Microtelecom site. With the same machine and using either the USB2 or the USB3 ports, SDR Console sees the Perseus when I add it but nothing happens when I start the radio and attempt to listen live. The hourglass just spins forever. The same thing happens when I try to play back a previously recorded Perseus file. SDR Console used to run perfectly on this machine, but I had not tried it in perhaps 8 months so don't really know when it broke.
Hello Simon,
A couple of days ago I verified that the dll works
fine on all USB3 ports of my i7 computer under 64 bit
Win 10. That was with a system updated until April 2016.
Today I updated my 64 bit Win 10 to the very latest
and I find that Linrad no longer works on the USB3
ports having VIA USB3 eXtensible Host Controller.
The driver date is 2017-09-28. Neither the 32 bit,
nor the 64 bit version works, but the Renesas ports
still work fine although they also have a new drive
routine.
I have not found any way to install the previous driver
for VIA.
An interesting thing is that perseus.exe works fine
with the new VIA driver. Both perseus v4.1 which uses
perseususb.dll and perseus.exe v5 which does not use
perseususb.dll.
It is obvious that I am doing something wrong in Linrad,
I will have a look at it to see if I can get Linrad going
with the latest Microsoft driver for VIA.
Question: Is there anyone who can not get perseus.exe
running on USB3 ports? I now know I have a USB3 problem
with Linrad - maybe I will be able to fix it, but I
do not expect Linrad to work on systems where perseus.exe
v5 does not run on USB3 ports.
73
Leif
> Thanks Leif.
>
> The driver works with some USB3 hardware but not all.
>
> Simon Brown, G4ELI
>
> https://eur02.safelinks.protection.outlook.com/?url=www.dxgalaxy.com&data=02%7C01%7Ccharlesh3%40msn.com%7C94e296aeab4d46e9585008d5391c08ba%7C84df9e7fe9f640afb435aaaaaaaaaaaa%7C1%7C0%7C636477714917915558&sdata=r8ms4Po2NxmUUhobQBOeZRLR7ay4zvZAmIhhDQoBobQ%3D&reserved=0
> https://eur02.safelinks.protection.outlook.com/?url=www.sdr-radio.com&data=02%7C01%7Ccharlesh3%40msn.com%7C94e296aeab4d46e9585008d5391c08ba%7C84df9e7fe9f640afb435aaaaaaaaaaaa%7C1%7C0%7C636477714917915558&sdata=4PzrWMgOF2spBjq9waSUCVfgwtEGXX5IC7rHrFEYOzE%3D&reserved=0
> https://eur02.safelinks.protection.outlook.com/?url=www.sdr-satellites.com&data=02%7C01%7Ccharlesh3%40msn.com%7C94e296aeab4d46e9585008d5391c08ba%7C84df9e7fe9f640afb435aaaaaaaaaaaa%7C1%7C0%7C636477714917915558&sdata=iFC3OooOhIgzG%2FwGquDP9VQWIt6H7tbCUzeaKeEcBrk%3D&reserved=0
>
>
> -----Original Message-----
> From: main@SDR-Radio.groups.io [mailto:main@SDR-Radio.groups.io] On Behalf
> Of Leif Asbrink
> Sent: 01 December 2017 00:34
> To: main@SDR-Radio.groups.io
> Subject: Re: [SDR-Radio] Problems with V3 console after 1709 W10
> installation
>
> Hi Simon,
>
> I do not know from where I got it. If you run the installer here
> https://eur02.safelinks.protection.outlook.com/?url=http%3A%2F%2Fsm5bsz.com%2Fdll.htm&data=02%7C01%7Ccharlesh3%40msn.com%7C94e296aeab4d46e9585008d5391c08ba%7C84df9e7fe9f640afb435aaaaaaaaaaaa%7C1%7C0%7C636477714917915558&sdata=mLbZVIZB0vuP5CHuJIq7ABT31kn9CcAgL4oJnLrUkzI%3D&reserved=0 you will find it in C:\linrad\dll\x64
>
> Size 126464 bytes. I do not remember from where I got it. I have attached
> the output from listdll64.exe
>
>
> Ihave now verified also on 64 bit Windows 10. I have
> motherboard USB2 and USB3 as well a PCIe card with
> USB3. All works well.
>
> The Win 10 installation I tested was not updated since
> maybe April 2016. I now updated Win10 to the latest
> version - and also the 32 bit Win 10 installation I
> have on the same computer. As a result I can no longer
> boot into the 64 bit system. Microsoft has written
> something to the 64 bit installation that directs boots
> to the 32 bit installation:-(
>
> This will take some time to repair - and I am afraid I
> will have to repair also Win 7 installations on the
> system (Four of them. Home and Ultimate 32 and 64 bit.
> Home allows only one CPU while Ultimate allows two.)
>
> Lesson learned: Do never upgrade Win 10 again on a multiboot
> system.
>
> I do not know if Microsoft would update the USB drivers
> and cause the perseususb to no longer work, but it does
> work well in the April 2016 system.
>
>
> 73
>
> Leif
>
>
> > Leif,
> >
> > Which Perseus 64-bit driver do you have?
> >
> > Simon Brown, G4ELI
> >
> > https://eur02.safelinks.protection.outlook.com/?url=www.dxgalaxy.com&data=02%7C01%7Ccharlesh3%40msn.com%7C94e296aeab4d46e9585008d5391c08ba%7C84df9e7fe9f640afb435aaaaaaaaaaaa%7C1%7C0%7C636477714917915558&sdata=r8ms4Po2NxmUUhobQBOeZRLR7ay4zvZAmIhhDQoBobQ%3D&reserved=0
> > https://eur02.safelinks.protection.outlook.com/?url=www.sdr-radio.com&data=02%7C01%7Ccharlesh3%40msn.com%7C94e296aeab4d46e9585008d5391c08ba%7C84df9e7fe9f640afb435aaaaaaaaaaaa%7C1%7C0%7C636477714917915558&sdata=4PzrWMgOF2spBjq9waSUCVfgwtEGXX5IC7rHrFEYOzE%3D&reserved=0
> > https://eur02.safelinks.protection.outlook.com/?url=www.sdr-satellites.com&data=02%7C01%7Ccharlesh3%40msn.com%7C94e296aeab4d46e9585008d5391c08ba%7C84df9e7fe9f640afb435aaaaaaaaaaaa%7C1%7C0%7C636477714917915558&sdata=iFC3OooOhIgzG%2FwGquDP9VQWIt6H7tbCUzeaKeEcBrk%3D&reserved=0
> >
> >
> > -----Original Message-----
> > From: main@SDR-Radio.groups.io [mailto:main@SDR-Radio.groups.io] On Behalf
> > Of Leif Asbrink
> >
> > Well, I had some problems in the past, but today, with the latest drive
> > routines for the USB system I have no problem on any
> > USB3 port on any of my computers.
> >
> > I would be interested to know if you would have any problem running
> Perseus
> > with Linrad on a "problematic" USB port.
> >
> > If you think it would be difficult I would make an install video showing
> the
> > very few commands you need. Just tell me what OS you are using.
> >
> > 73
> >
> > Leif
> >
> >
> >
> >
> >
>
>
>
>
>
>
>
|
|
|
Simon Brown
Hi,
This is interesting - I'll try something tomorrow then maybe ask for some diagnsotics.
Simon Brown, G4ELI
www.dxgalaxy.com
www.sdr-radio.com
www.sdr-satellites.com
toggle quoted message
Show quoted text
-----Original Message-----
From: main@SDR-Radio.groups.io [mailto:main@SDR-Radio.groups.io] On Behalf Of ww6rb
Sent: 02 December 2017 20:42
To: main@SDR-Radio.groups.io
Subject: [SDR-Radio] V3 Freeze Fix
In case this may be useful to the dwindling few people still affected:
A while back we installed a GTX-950 in a heavy duty (always offline)
Win7 machine to fully exercise V3.
V3 crashed as described ad nauseam previously, while V2 and everything else worked as usual.
Eventually we ripped out the NVIDIA drivers altogether and reverted to non CUDA operation... fine but... no CUDA.
Last week compulsion won out and we began retrotracking thru the list of drivers available on the NVIDIA site... download to save... install with no extras... crash... remove... repeat.
388.31... 395.69... etc, etc, to the bottom of the list... 376.33
376.33 works! No slow opens, no hangs, no freezes, no memory leaks to
infinity... running full bore at 40 MHz gives a few % CPU and a few % GPU.
Guessing it's not a win dll... but don't really have to care anymore...
WoooHoo! Life is fun again! :))
Thanks, Simon!
-rb-
WW6RB
PS: NetSDR / Scott's Blade / PlayPro / R2 all working great under V3...
+ on order... hoping by Christmas!
|
|
|
Re: Perseus on USB3 ports. (was Problems with V3 console after 1709 W10 installation)
Simon Brown
toggle quoted message
Show quoted text
From: main@SDR-Radio.groups.io [mailto:main@SDR-Radio.groups.io] On Behalf Of n4dcd@...
Sent: 02 December 2017 20:31
To: main@SDR-Radio.groups.io
Subject: Re: [SDR-Radio] Perseus on USB3 ports. (was Problems with V3 console after 1709 W10 installation) Simon When to predict the final release of SDR_Console?
|
|
|
Re: Perseus on USB3 ports. (was Problems with V3 console after 1709 W10 installation)
Simon
When to predict the final release of SDR_Console?
|
|
|
In case this may be useful to the dwindling few people still affected:
A while back we installed a GTX-950 in a heavy duty (always offline) Win7 machine to fully exercise V3.
V3 crashed as described ad nauseam previously, while V2 and everything else worked as usual.
Eventually we ripped out the NVIDIA drivers altogether and reverted to non CUDA operation... fine but... no CUDA.
Last week compulsion won out and we began retrotracking thru the list of drivers available on the NVIDIA site... download to save... install with no extras... crash... remove... repeat.
388.31... 395.69... etc, etc, to the bottom of the list... 376.33
376.33 works! No slow opens, no hangs, no freezes, no memory leaks to infinity... running full bore at 40 MHz gives a few % CPU and a few % GPU.
Guessing it's not a win dll... but don't really have to care anymore... WoooHoo! Life is fun again! :))
Thanks, Simon!
-rb-
WW6RB
PS: NetSDR / Scott's Blade / PlayPro / R2 all working great under V3... + on order... hoping by Christmas!
|
|
|
Re: Default volume going to 100% when switching between satellites in the satellites list.
Hi Simon
Ah, that explains it
J
Thanks for getting back to me in your very busy schedule.
Neal
G1UQK
toggle quoted message
Show quoted text
From: main@SDR-Radio.groups.io [mailto:main@SDR-Radio.groups.io]
On Behalf Of Simon Brown
Sent: 01 December 2017 17:09
To: main@SDR-Radio.groups.io
Subject: Re: [SDR-Radio] Default volume going to 100% when switching between satellites in the satellites list.
Hi,
Added on purpose, pain it is, now no longer applied
😊 .
Hi Simon
Firstly, keep up all the good work. This is by far the best SDR program out there.
When I switch between satellites using the Satellites list the volume is automatically going to 100% no matter what level I choose while on a particular satellite. This would not normally be a problem but when you are using headphones in
a shared room it not only makes me jump out of my skin but also those around me. Is there a setting that sets a default volume per satellite?
I am also not sure when this started happening as I have not had chance to do anything with satellites for a while and I know you have released a few new versions since I last used it.
Also I am not sure if anyone else has reported this as I did try a search but it didn’t return any results that helped.
I know you usually need screenshots but wasn’t sure what screenshot you would need so I have added a screenshot of the main console with the volume at a lower level and a screenshot to show what satellite was selected. Then there is one
where I have changed the satellite and the last is the main console showing the volume at 100%
Not an urgent one but wanted to make sure it wasn’t a bug ;-)
All the best
Neal
G1UQK
|
|
|
Re: Perseus on USB3 ports. (was Problems with V3 console after 1709 W10 installation)
More info: (and I should have added this before)
The playback fails (hangs up) if the receiver has been started. If the receiver is not started, I can play back OK.
I believe the USB to the Perseus is OK as the Perseus is configured properly when the radio is started. It's just that nothing happens afterwards. The spectrum display never shows anything and there is no audio.
Chuck
toggle quoted message
Show quoted text
From: Chuck Hutton <charlesh3@...>
Sent: Saturday, December 2, 2017 12:02 PM
To: main@SDR-Radio.groups.io
Subject: Re: [SDR-Radio] Perseus on USB3 ports. (was Problems with V3 console after 1709 W10 installation)
Simon -
As mentioned, the hourglass spins forever and the program doesn't respond. So I assume that there's no way to do the normal SDR Console screen capture.
Chuck
From: main@SDR-Radio.groups.io <main@SDR-Radio.groups.io> on behalf of Simon Brown <simon@...>
Sent: Saturday, December 2, 2017 11:11 AM
To: main@SDR-Radio.groups.io
Subject: Re: [SDR-Radio] Perseus on USB3 ports. (was Problems with V3 console after 1709 W10 installation)
Chuck,
You threw me with the Perseus reference. If you can’t play files then yes, it’s borked. There’s a reset option, also you can post a screenshot.
From: main@SDR-Radio.groups.io [mailto:main@SDR-Radio.groups.io]
On Behalf Of chutton12000
Sent: 02 December 2017 18:41
To: main@SDR-Radio.groups.io
Subject: Re: [SDR-Radio] Perseus on USB3 ports. (was Problems with V3 console after 1709 W10 installation)
Hi Simon -
I;m aware of the info at your link but....
(1) USB issues shouldn't affect playback of previously recorded files.
(2) SDR Console worked OK with my Perseus in 2015-2016-early 2017.
Does adding the Perseus definition and having it accepted mean that Console found the Perseus?
Chuck,
Everything I know about Perseus is on the website
http://www.sdr-radio.com/Radios/Perseus .
Here is a problem that may or may not have a common root. On my Win 10 x64 machine with 1709 uodates -
all ports (USB2 and 3) work with the native Perseus software ver 4.1. I have the signed USB drivers installed, as supplied on the Microtelecom site.
With the same machine and using either the USB2 or the USB3 ports, SDR Console sees the Perseus when I add it but nothing happens when I start the radio and attempt to listen live. The hourglass just spins forever.
The same thing happens when I try to play back a previously recorded Perseus file.
SDR Console used to run perfectly on this machine, but I had not tried it in perhaps 8 months so don't really know when it broke.
Hello Simon,
A couple of days ago I verified that the dll works
fine on all USB3 ports of my i7 computer under 64 bit
Win 10. That was with a system updated until April 2016.
Today I updated my 64 bit Win 10 to the very latest
and I find that Linrad no longer works on the USB3
ports having VIA USB3 eXtensible Host Controller.
The driver date is 2017-09-28. Neither the 32 bit,
nor the 64 bit version works, but the Renesas ports
still work fine although they also have a new drive
routine.
I have not found any way to install the previous driver
for VIA.
An interesting thing is that perseus.exe works fine
with the new VIA driver. Both perseus v4.1 which uses
perseususb.dll and perseus.exe v5 which does not use
perseususb.dll.
It is obvious that I am doing something wrong in Linrad,
I will have a look at it to see if I can get Linrad going
with the latest Microsoft driver for VIA.
Question: Is there anyone who can not get perseus.exe
running on USB3 ports? I now know I have a USB3 problem
with Linrad - maybe I will be able to fix it, but I
do not expect Linrad to work on systems where perseus.exe
v5 does not run on USB3 ports.
73
Leif
> Thanks Leif.
>
> The driver works with some USB3 hardware but not all.
>
> Simon Brown, G4ELI
>
>
https://eur02.safelinks.protection.outlook.com/?url=www.dxgalaxy.com&data=02%7C01%7Ccharlesh3%40msn.com%7C94e296aeab4d46e9585008d5391c08ba%7C84df9e7fe9f640afb435aaaaaaaaaaaa%7C1%7C0%7C636477714917915558&sdata=r8ms4Po2NxmUUhobQBOeZRLR7ay4zvZAmIhhDQoBobQ%3D&reserved=0
>
https://eur02.safelinks.protection.outlook.com/?url=www.sdr-radio.com&data=02%7C01%7Ccharlesh3%40msn.com%7C94e296aeab4d46e9585008d5391c08ba%7C84df9e7fe9f640afb435aaaaaaaaaaaa%7C1%7C0%7C636477714917915558&sdata=4PzrWMgOF2spBjq9waSUCVfgwtEGXX5IC7rHrFEYOzE%3D&reserved=0
>
https://eur02.safelinks.protection.outlook.com/?url=www.sdr-satellites.com&data=02%7C01%7Ccharlesh3%40msn.com%7C94e296aeab4d46e9585008d5391c08ba%7C84df9e7fe9f640afb435aaaaaaaaaaaa%7C1%7C0%7C636477714917915558&sdata=iFC3OooOhIgzG%2FwGquDP9VQWIt6H7tbCUzeaKeEcBrk%3D&reserved=0
>
>
> -----Original Message-----
> From: main@SDR-Radio.groups.io [mailto:main@SDR-Radio.groups.io] On Behalf
> Of Leif Asbrink
> Sent: 01 December 2017 00:34
> To: main@SDR-Radio.groups.io
> Subject: Re: [SDR-Radio] Problems with V3 console after 1709 W10
> installation
>
> Hi Simon,
>
> I do not know from where I got it. If you run the installer here
>
https://eur02.safelinks.protection.outlook.com/?url=http%3A%2F%2Fsm5bsz.com%2Fdll.htm&data=02%7C01%7Ccharlesh3%40msn.com%7C94e296aeab4d46e9585008d5391c08ba%7C84df9e7fe9f640afb435aaaaaaaaaaaa%7C1%7C0%7C636477714917915558&sdata=mLbZVIZB0vuP5CHuJIq7ABT31kn9CcAgL4oJnLrUkzI%3D&reserved=0
you will find it in C:\linrad\dll\x64
>
> Size 126464 bytes. I do not remember from where I got it. I have attached
> the output from listdll64.exe
>
>
> Ihave now verified also on 64 bit Windows 10. I have
> motherboard USB2 and USB3 as well a PCIe card with
> USB3. All works well.
>
> The Win 10 installation I tested was not updated since
> maybe April 2016. I now updated Win10 to the latest
> version - and also the 32 bit Win 10 installation I
> have on the same computer. As a result I can no longer
> boot into the 64 bit system. Microsoft has written
> something to the 64 bit installation that directs boots
> to the 32 bit installation:-(
>
> This will take some time to repair - and I am afraid I
> will have to repair also Win 7 installations on the
> system (Four of them. Home and Ultimate 32 and 64 bit.
> Home allows only one CPU while Ultimate allows two.)
>
> Lesson learned: Do never upgrade Win 10 again on a multiboot
> system.
>
> I do not know if Microsoft would update the USB drivers
> and cause the perseususb to no longer work, but it does
> work well in the April 2016 system.
>
>
> 73
>
> Leif
>
>
> > Leif,
> >
> > Which Perseus 64-bit driver do you have?
> >
> > Simon Brown, G4ELI
> >
> >
https://eur02.safelinks.protection.outlook.com/?url=www.dxgalaxy.com&data=02%7C01%7Ccharlesh3%40msn.com%7C94e296aeab4d46e9585008d5391c08ba%7C84df9e7fe9f640afb435aaaaaaaaaaaa%7C1%7C0%7C636477714917915558&sdata=r8ms4Po2NxmUUhobQBOeZRLR7ay4zvZAmIhhDQoBobQ%3D&reserved=0
> >
https://eur02.safelinks.protection.outlook.com/?url=www.sdr-radio.com&data=02%7C01%7Ccharlesh3%40msn.com%7C94e296aeab4d46e9585008d5391c08ba%7C84df9e7fe9f640afb435aaaaaaaaaaaa%7C1%7C0%7C636477714917915558&sdata=4PzrWMgOF2spBjq9waSUCVfgwtEGXX5IC7rHrFEYOzE%3D&reserved=0
> >
https://eur02.safelinks.protection.outlook.com/?url=www.sdr-satellites.com&data=02%7C01%7Ccharlesh3%40msn.com%7C94e296aeab4d46e9585008d5391c08ba%7C84df9e7fe9f640afb435aaaaaaaaaaaa%7C1%7C0%7C636477714917915558&sdata=iFC3OooOhIgzG%2FwGquDP9VQWIt6H7tbCUzeaKeEcBrk%3D&reserved=0
> >
> >
> > -----Original Message-----
> > From: main@SDR-Radio.groups.io [mailto:main@SDR-Radio.groups.io] On Behalf
> > Of Leif Asbrink
> >
> > Well, I had some problems in the past, but today, with the latest drive
> > routines for the USB system I have no problem on any
> > USB3 port on any of my computers.
> >
> > I would be interested to know if you would have any problem running
> Perseus
> > with Linrad on a "problematic" USB port.
> >
> > If you think it would be difficult I would make an install video showing
> the
> > very few commands you need. Just tell me what OS you are using.
> >
> > 73
> >
> > Leif
> >
> >
> >
> >
> >
>
>
>
>
>
>
>
|
|
|
Re: Perseus on USB3 ports. (was Problems with V3 console after 1709 W10 installation)
Simon -
As mentioned, the hourglass spins forever and the program doesn't respond. So I assume that there's no way to do the normal SDR Console screen capture.
Chuck
toggle quoted message
Show quoted text
From: main@SDR-Radio.groups.io <main@SDR-Radio.groups.io> on behalf of Simon Brown <simon@...>
Sent: Saturday, December 2, 2017 11:11 AM
To: main@SDR-Radio.groups.io
Subject: Re: [SDR-Radio] Perseus on USB3 ports. (was Problems with V3 console after 1709 W10 installation)
Chuck,
You threw me with the Perseus reference. If you can’t play files then yes, it’s borked. There’s a reset option, also you can post a screenshot.
From: main@SDR-Radio.groups.io [mailto:main@SDR-Radio.groups.io]
On Behalf Of chutton12000
Sent: 02 December 2017 18:41
To: main@SDR-Radio.groups.io
Subject: Re: [SDR-Radio] Perseus on USB3 ports. (was Problems with V3 console after 1709 W10 installation)
Hi Simon -
I;m aware of the info at your link but....
(1) USB issues shouldn't affect playback of previously recorded files.
(2) SDR Console worked OK with my Perseus in 2015-2016-early 2017.
Does adding the Perseus definition and having it accepted mean that Console found the Perseus?
Chuck,
Everything I know about Perseus is on the website
http://www.sdr-radio.com/Radios/Perseus .
Here is a problem that may or may not have a common root. On my Win 10 x64 machine with 1709 uodates -
all ports (USB2 and 3) work with the native Perseus software ver 4.1. I have the signed USB drivers installed, as supplied on the Microtelecom site.
With the same machine and using either the USB2 or the USB3 ports, SDR Console sees the Perseus when I add it but nothing happens when I start the radio and attempt to listen live. The hourglass just spins forever.
The same thing happens when I try to play back a previously recorded Perseus file.
SDR Console used to run perfectly on this machine, but I had not tried it in perhaps 8 months so don't really know when it broke.
Hello Simon,
A couple of days ago I verified that the dll works
fine on all USB3 ports of my i7 computer under 64 bit
Win 10. That was with a system updated until April 2016.
Today I updated my 64 bit Win 10 to the very latest
and I find that Linrad no longer works on the USB3
ports having VIA USB3 eXtensible Host Controller.
The driver date is 2017-09-28. Neither the 32 bit,
nor the 64 bit version works, but the Renesas ports
still work fine although they also have a new drive
routine.
I have not found any way to install the previous driver
for VIA.
An interesting thing is that perseus.exe works fine
with the new VIA driver. Both perseus v4.1 which uses
perseususb.dll and perseus.exe v5 which does not use
perseususb.dll.
It is obvious that I am doing something wrong in Linrad,
I will have a look at it to see if I can get Linrad going
with the latest Microsoft driver for VIA.
Question: Is there anyone who can not get perseus.exe
running on USB3 ports? I now know I have a USB3 problem
with Linrad - maybe I will be able to fix it, but I
do not expect Linrad to work on systems where perseus.exe
v5 does not run on USB3 ports.
73
Leif
> Thanks Leif.
>
> The driver works with some USB3 hardware but not all.
>
> Simon Brown, G4ELI
>
>
https://eur02.safelinks.protection.outlook.com/?url=www.dxgalaxy.com&data=02%7C01%7Ccharlesh3%40msn.com%7C94e296aeab4d46e9585008d5391c08ba%7C84df9e7fe9f640afb435aaaaaaaaaaaa%7C1%7C0%7C636477714917915558&sdata=r8ms4Po2NxmUUhobQBOeZRLR7ay4zvZAmIhhDQoBobQ%3D&reserved=0
>
https://eur02.safelinks.protection.outlook.com/?url=www.sdr-radio.com&data=02%7C01%7Ccharlesh3%40msn.com%7C94e296aeab4d46e9585008d5391c08ba%7C84df9e7fe9f640afb435aaaaaaaaaaaa%7C1%7C0%7C636477714917915558&sdata=4PzrWMgOF2spBjq9waSUCVfgwtEGXX5IC7rHrFEYOzE%3D&reserved=0
>
https://eur02.safelinks.protection.outlook.com/?url=www.sdr-satellites.com&data=02%7C01%7Ccharlesh3%40msn.com%7C94e296aeab4d46e9585008d5391c08ba%7C84df9e7fe9f640afb435aaaaaaaaaaaa%7C1%7C0%7C636477714917915558&sdata=iFC3OooOhIgzG%2FwGquDP9VQWIt6H7tbCUzeaKeEcBrk%3D&reserved=0
>
>
> -----Original Message-----
> From: main@SDR-Radio.groups.io [mailto:main@SDR-Radio.groups.io] On Behalf
> Of Leif Asbrink
> Sent: 01 December 2017 00:34
> To: main@SDR-Radio.groups.io
> Subject: Re: [SDR-Radio] Problems with V3 console after 1709 W10
> installation
>
> Hi Simon,
>
> I do not know from where I got it. If you run the installer here
>
https://eur02.safelinks.protection.outlook.com/?url=http%3A%2F%2Fsm5bsz.com%2Fdll.htm&data=02%7C01%7Ccharlesh3%40msn.com%7C94e296aeab4d46e9585008d5391c08ba%7C84df9e7fe9f640afb435aaaaaaaaaaaa%7C1%7C0%7C636477714917915558&sdata=mLbZVIZB0vuP5CHuJIq7ABT31kn9CcAgL4oJnLrUkzI%3D&reserved=0
you will find it in C:\linrad\dll\x64
>
> Size 126464 bytes. I do not remember from where I got it. I have attached
> the output from listdll64.exe
>
>
> Ihave now verified also on 64 bit Windows 10. I have
> motherboard USB2 and USB3 as well a PCIe card with
> USB3. All works well.
>
> The Win 10 installation I tested was not updated since
> maybe April 2016. I now updated Win10 to the latest
> version - and also the 32 bit Win 10 installation I
> have on the same computer. As a result I can no longer
> boot into the 64 bit system. Microsoft has written
> something to the 64 bit installation that directs boots
> to the 32 bit installation:-(
>
> This will take some time to repair - and I am afraid I
> will have to repair also Win 7 installations on the
> system (Four of them. Home and Ultimate 32 and 64 bit.
> Home allows only one CPU while Ultimate allows two.)
>
> Lesson learned: Do never upgrade Win 10 again on a multiboot
> system.
>
> I do not know if Microsoft would update the USB drivers
> and cause the perseususb to no longer work, but it does
> work well in the April 2016 system.
>
>
> 73
>
> Leif
>
>
> > Leif,
> >
> > Which Perseus 64-bit driver do you have?
> >
> > Simon Brown, G4ELI
> >
> >
https://eur02.safelinks.protection.outlook.com/?url=www.dxgalaxy.com&data=02%7C01%7Ccharlesh3%40msn.com%7C94e296aeab4d46e9585008d5391c08ba%7C84df9e7fe9f640afb435aaaaaaaaaaaa%7C1%7C0%7C636477714917915558&sdata=r8ms4Po2NxmUUhobQBOeZRLR7ay4zvZAmIhhDQoBobQ%3D&reserved=0
> >
https://eur02.safelinks.protection.outlook.com/?url=www.sdr-radio.com&data=02%7C01%7Ccharlesh3%40msn.com%7C94e296aeab4d46e9585008d5391c08ba%7C84df9e7fe9f640afb435aaaaaaaaaaaa%7C1%7C0%7C636477714917915558&sdata=4PzrWMgOF2spBjq9waSUCVfgwtEGXX5IC7rHrFEYOzE%3D&reserved=0
> >
https://eur02.safelinks.protection.outlook.com/?url=www.sdr-satellites.com&data=02%7C01%7Ccharlesh3%40msn.com%7C94e296aeab4d46e9585008d5391c08ba%7C84df9e7fe9f640afb435aaaaaaaaaaaa%7C1%7C0%7C636477714917915558&sdata=iFC3OooOhIgzG%2FwGquDP9VQWIt6H7tbCUzeaKeEcBrk%3D&reserved=0
> >
> >
> > -----Original Message-----
> > From: main@SDR-Radio.groups.io [mailto:main@SDR-Radio.groups.io] On Behalf
> > Of Leif Asbrink
> >
> > Well, I had some problems in the past, but today, with the latest drive
> > routines for the USB system I have no problem on any
> > USB3 port on any of my computers.
> >
> > I would be interested to know if you would have any problem running
> Perseus
> > with Linrad on a "problematic" USB port.
> >
> > If you think it would be difficult I would make an install video showing
> the
> > very few commands you need. Just tell me what OS you are using.
> >
> > 73
> >
> > Leif
> >
> >
> >
> >
> >
>
>
>
>
>
>
>
|
|
|
Re: Perseus on USB3 ports. (was Problems with V3 console after 1709 W10 installation)
Simon Brown
Chuck, You threw me with the Perseus reference. If you can’t play files then yes, it’s borked. There’s a reset option, also you can post a screenshot.
From: main@SDR-Radio.groups.io [mailto:main@SDR-Radio.groups.io] On Behalf Of chutton12000
Sent: 02 December 2017 18:41
To: main@SDR-Radio.groups.io
Subject: Re: [SDR-Radio] Perseus on USB3 ports. (was Problems with V3 console after 1709 W10 installation) Hi Simon - I;m aware of the info at your link but.... (1) USB issues shouldn't affect playback of previously recorded files. (2) SDR Console worked OK with my Perseus in 2015-2016-early 2017. Does adding the Perseus definition and having it accepted mean that Console found the Perseus?
Chuck, Everything I know about Perseus is on the website http://www.sdr-radio.com/Radios/Perseus . Here is a problem that may or may not have a common root. On my Win 10 x64 machine with 1709 uodates - all ports (USB2 and 3) work with the native Perseus software ver 4.1. I have the signed USB drivers installed, as supplied on the Microtelecom site. With the same machine and using either the USB2 or the USB3 ports, SDR Console sees the Perseus when I add it but nothing happens when I start the radio and attempt to listen live. The hourglass just spins forever. The same thing happens when I try to play back a previously recorded Perseus file. SDR Console used to run perfectly on this machine, but I had not tried it in perhaps 8 months so don't really know when it broke.
Hello Simon,
A couple of days ago I verified that the dll works
fine on all USB3 ports of my i7 computer under 64 bit
Win 10. That was with a system updated until April 2016.
Today I updated my 64 bit Win 10 to the very latest
and I find that Linrad no longer works on the USB3
ports having VIA USB3 eXtensible Host Controller.
The driver date is 2017-09-28. Neither the 32 bit,
nor the 64 bit version works, but the Renesas ports
still work fine although they also have a new drive
routine.
I have not found any way to install the previous driver
for VIA.
An interesting thing is that perseus.exe works fine
with the new VIA driver. Both perseus v4.1 which uses
perseususb.dll and perseus.exe v5 which does not use
perseususb.dll.
It is obvious that I am doing something wrong in Linrad,
I will have a look at it to see if I can get Linrad going
with the latest Microsoft driver for VIA.
Question: Is there anyone who can not get perseus.exe
running on USB3 ports? I now know I have a USB3 problem
with Linrad - maybe I will be able to fix it, but I
do not expect Linrad to work on systems where perseus.exe
v5 does not run on USB3 ports.
73
Leif
> Thanks Leif.
>
> The driver works with some USB3 hardware but not all.
>
> Simon Brown, G4ELI
>
> https://eur02.safelinks.protection.outlook.com/?url=www.dxgalaxy.com&data=02%7C01%7Ccharlesh3%40msn.com%7C94e296aeab4d46e9585008d5391c08ba%7C84df9e7fe9f640afb435aaaaaaaaaaaa%7C1%7C0%7C636477714917915558&sdata=r8ms4Po2NxmUUhobQBOeZRLR7ay4zvZAmIhhDQoBobQ%3D&reserved=0
> https://eur02.safelinks.protection.outlook.com/?url=www.sdr-radio.com&data=02%7C01%7Ccharlesh3%40msn.com%7C94e296aeab4d46e9585008d5391c08ba%7C84df9e7fe9f640afb435aaaaaaaaaaaa%7C1%7C0%7C636477714917915558&sdata=4PzrWMgOF2spBjq9waSUCVfgwtEGXX5IC7rHrFEYOzE%3D&reserved=0
> https://eur02.safelinks.protection.outlook.com/?url=www.sdr-satellites.com&data=02%7C01%7Ccharlesh3%40msn.com%7C94e296aeab4d46e9585008d5391c08ba%7C84df9e7fe9f640afb435aaaaaaaaaaaa%7C1%7C0%7C636477714917915558&sdata=iFC3OooOhIgzG%2FwGquDP9VQWIt6H7tbCUzeaKeEcBrk%3D&reserved=0
>
>
> -----Original Message-----
> From: main@SDR-Radio.groups.io [mailto:main@SDR-Radio.groups.io] On Behalf
> Of Leif Asbrink
> Sent: 01 December 2017 00:34
> To: main@SDR-Radio.groups.io
> Subject: Re: [SDR-Radio] Problems with V3 console after 1709 W10
> installation
>
> Hi Simon,
>
> I do not know from where I got it. If you run the installer here
> https://eur02.safelinks.protection.outlook.com/?url=http%3A%2F%2Fsm5bsz.com%2Fdll.htm&data=02%7C01%7Ccharlesh3%40msn.com%7C94e296aeab4d46e9585008d5391c08ba%7C84df9e7fe9f640afb435aaaaaaaaaaaa%7C1%7C0%7C636477714917915558&sdata=mLbZVIZB0vuP5CHuJIq7ABT31kn9CcAgL4oJnLrUkzI%3D&reserved=0 you will find it in C:\linrad\dll\x64
>
> Size 126464 bytes. I do not remember from where I got it. I have attached
> the output from listdll64.exe
>
>
> Ihave now verified also on 64 bit Windows 10. I have
> motherboard USB2 and USB3 as well a PCIe card with
> USB3. All works well.
>
> The Win 10 installation I tested was not updated since
> maybe April 2016. I now updated Win10 to the latest
> version - and also the 32 bit Win 10 installation I
> have on the same computer. As a result I can no longer
> boot into the 64 bit system. Microsoft has written
> something to the 64 bit installation that directs boots
> to the 32 bit installation:-(
>
> This will take some time to repair - and I am afraid I
> will have to repair also Win 7 installations on the
> system (Four of them. Home and Ultimate 32 and 64 bit.
> Home allows only one CPU while Ultimate allows two.)
>
> Lesson learned: Do never upgrade Win 10 again on a multiboot
> system.
>
> I do not know if Microsoft would update the USB drivers
> and cause the perseususb to no longer work, but it does
> work well in the April 2016 system.
>
>
> 73
>
> Leif
>
>
> > Leif,
> >
> > Which Perseus 64-bit driver do you have?
> >
> > Simon Brown, G4ELI
> >
> > https://eur02.safelinks.protection.outlook.com/?url=www.dxgalaxy.com&data=02%7C01%7Ccharlesh3%40msn.com%7C94e296aeab4d46e9585008d5391c08ba%7C84df9e7fe9f640afb435aaaaaaaaaaaa%7C1%7C0%7C636477714917915558&sdata=r8ms4Po2NxmUUhobQBOeZRLR7ay4zvZAmIhhDQoBobQ%3D&reserved=0
> > https://eur02.safelinks.protection.outlook.com/?url=www.sdr-radio.com&data=02%7C01%7Ccharlesh3%40msn.com%7C94e296aeab4d46e9585008d5391c08ba%7C84df9e7fe9f640afb435aaaaaaaaaaaa%7C1%7C0%7C636477714917915558&sdata=4PzrWMgOF2spBjq9waSUCVfgwtEGXX5IC7rHrFEYOzE%3D&reserved=0
> > https://eur02.safelinks.protection.outlook.com/?url=www.sdr-satellites.com&data=02%7C01%7Ccharlesh3%40msn.com%7C94e296aeab4d46e9585008d5391c08ba%7C84df9e7fe9f640afb435aaaaaaaaaaaa%7C1%7C0%7C636477714917915558&sdata=iFC3OooOhIgzG%2FwGquDP9VQWIt6H7tbCUzeaKeEcBrk%3D&reserved=0
> >
> >
> > -----Original Message-----
> > From: main@SDR-Radio.groups.io [mailto:main@SDR-Radio.groups.io] On Behalf
> > Of Leif Asbrink
> >
> > Well, I had some problems in the past, but today, with the latest drive
> > routines for the USB system I have no problem on any
> > USB3 port on any of my computers.
> >
> > I would be interested to know if you would have any problem running
> Perseus
> > with Linrad on a "problematic" USB port.
> >
> > If you think it would be difficult I would make an install video showing
> the
> > very few commands you need. Just tell me what OS you are using.
> >
> > 73
> >
> > Leif
> >
> >
> >
> >
> >
>
>
>
>
>
>
>
|
|
|
Re: Perseus on USB3 ports. (was Problems with V3 console after 1709 W10 installation)
Hi Simon -
I;m aware of the info at your link but....
(1) USB issues shouldn't affect playback of previously recorded files.
(2) SDR Console worked OK with my Perseus in 2015-2016-early 2017.
Does adding the Perseus definition and having it accepted mean that Console found the Perseus?
Chuck
toggle quoted message
Show quoted text
From: main@SDR-Radio.groups.io <main@SDR-Radio.groups.io> on behalf of Simon Brown <simon@...>
Sent: Friday, December 1, 2017 11:22 PM
To: main@SDR-Radio.groups.io
Subject: Re: [SDR-Radio] Perseus on USB3 ports. (was Problems with V3 console after 1709 W10 installation)
Chuck,
Everything I know about Perseus is on the website
http://www.sdr-radio.com/Radios/Perseus .
From: main@SDR-Radio.groups.io [mailto:main@SDR-Radio.groups.io]
On Behalf Of chutton12000
Sent: 02 December 2017 01:28
To: main@SDR-Radio.groups.io
Subject: Re: [SDR-Radio] Perseus on USB3 ports. (was Problems with V3 console after 1709 W10 installation)
Here is a problem that may or may not have a common root. On my Win 10 x64 machine with 1709 uodates -
all ports (USB2 and 3) work with the native Perseus software ver 4.1. I have the signed USB drivers installed, as supplied on the Microtelecom site.
With the same machine and using either the USB2 or the USB3 ports, SDR Console sees the Perseus when I add it but nothing happens when I start the radio and attempt to listen live. The hourglass just spins forever.
The same thing happens when I try to play back a previously recorded Perseus file.
SDR Console used to run perfectly on this machine, but I had not tried it in perhaps 8 months so don't really know when it broke.
Hello Simon,
A couple of days ago I verified that the dll works
fine on all USB3 ports of my i7 computer under 64 bit
Win 10. That was with a system updated until April 2016.
Today I updated my 64 bit Win 10 to the very latest
and I find that Linrad no longer works on the USB3
ports having VIA USB3 eXtensible Host Controller.
The driver date is 2017-09-28. Neither the 32 bit,
nor the 64 bit version works, but the Renesas ports
still work fine although they also have a new drive
routine.
I have not found any way to install the previous driver
for VIA.
An interesting thing is that perseus.exe works fine
with the new VIA driver. Both perseus v4.1 which uses
perseususb.dll and perseus.exe v5 which does not use
perseususb.dll.
It is obvious that I am doing something wrong in Linrad,
I will have a look at it to see if I can get Linrad going
with the latest Microsoft driver for VIA.
Question: Is there anyone who can not get perseus.exe
running on USB3 ports? I now know I have a USB3 problem
with Linrad - maybe I will be able to fix it, but I
do not expect Linrad to work on systems where perseus.exe
v5 does not run on USB3 ports.
73
Leif
> Thanks Leif.
>
> The driver works with some USB3 hardware but not all.
>
> Simon Brown, G4ELI
>
>
https://eur02.safelinks.protection.outlook.com/?url=www.dxgalaxy.com&data=02%7C01%7Ccharlesh3%40msn.com%7C94e296aeab4d46e9585008d5391c08ba%7C84df9e7fe9f640afb435aaaaaaaaaaaa%7C1%7C0%7C636477714917915558&sdata=r8ms4Po2NxmUUhobQBOeZRLR7ay4zvZAmIhhDQoBobQ%3D&reserved=0
>
https://eur02.safelinks.protection.outlook.com/?url=www.sdr-radio.com&data=02%7C01%7Ccharlesh3%40msn.com%7C94e296aeab4d46e9585008d5391c08ba%7C84df9e7fe9f640afb435aaaaaaaaaaaa%7C1%7C0%7C636477714917915558&sdata=4PzrWMgOF2spBjq9waSUCVfgwtEGXX5IC7rHrFEYOzE%3D&reserved=0
>
https://eur02.safelinks.protection.outlook.com/?url=www.sdr-satellites.com&data=02%7C01%7Ccharlesh3%40msn.com%7C94e296aeab4d46e9585008d5391c08ba%7C84df9e7fe9f640afb435aaaaaaaaaaaa%7C1%7C0%7C636477714917915558&sdata=iFC3OooOhIgzG%2FwGquDP9VQWIt6H7tbCUzeaKeEcBrk%3D&reserved=0
>
>
> -----Original Message-----
> From: main@SDR-Radio.groups.io [mailto:main@SDR-Radio.groups.io] On Behalf
> Of Leif Asbrink
> Sent: 01 December 2017 00:34
> To: main@SDR-Radio.groups.io
> Subject: Re: [SDR-Radio] Problems with V3 console after 1709 W10
> installation
>
> Hi Simon,
>
> I do not know from where I got it. If you run the installer here
>
https://eur02.safelinks.protection.outlook.com/?url=http%3A%2F%2Fsm5bsz.com%2Fdll.htm&data=02%7C01%7Ccharlesh3%40msn.com%7C94e296aeab4d46e9585008d5391c08ba%7C84df9e7fe9f640afb435aaaaaaaaaaaa%7C1%7C0%7C636477714917915558&sdata=mLbZVIZB0vuP5CHuJIq7ABT31kn9CcAgL4oJnLrUkzI%3D&reserved=0
you will find it in C:\linrad\dll\x64
>
> Size 126464 bytes. I do not remember from where I got it. I have attached
> the output from listdll64.exe
>
>
> Ihave now verified also on 64 bit Windows 10. I have
> motherboard USB2 and USB3 as well a PCIe card with
> USB3. All works well.
>
> The Win 10 installation I tested was not updated since
> maybe April 2016. I now updated Win10 to the latest
> version - and also the 32 bit Win 10 installation I
> have on the same computer. As a result I can no longer
> boot into the 64 bit system. Microsoft has written
> something to the 64 bit installation that directs boots
> to the 32 bit installation:-(
>
> This will take some time to repair - and I am afraid I
> will have to repair also Win 7 installations on the
> system (Four of them. Home and Ultimate 32 and 64 bit.
> Home allows only one CPU while Ultimate allows two.)
>
> Lesson learned: Do never upgrade Win 10 again on a multiboot
> system.
>
> I do not know if Microsoft would update the USB drivers
> and cause the perseususb to no longer work, but it does
> work well in the April 2016 system.
>
>
> 73
>
> Leif
>
>
> > Leif,
> >
> > Which Perseus 64-bit driver do you have?
> >
> > Simon Brown, G4ELI
> >
> >
https://eur02.safelinks.protection.outlook.com/?url=www.dxgalaxy.com&data=02%7C01%7Ccharlesh3%40msn.com%7C94e296aeab4d46e9585008d5391c08ba%7C84df9e7fe9f640afb435aaaaaaaaaaaa%7C1%7C0%7C636477714917915558&sdata=r8ms4Po2NxmUUhobQBOeZRLR7ay4zvZAmIhhDQoBobQ%3D&reserved=0
> >
https://eur02.safelinks.protection.outlook.com/?url=www.sdr-radio.com&data=02%7C01%7Ccharlesh3%40msn.com%7C94e296aeab4d46e9585008d5391c08ba%7C84df9e7fe9f640afb435aaaaaaaaaaaa%7C1%7C0%7C636477714917915558&sdata=4PzrWMgOF2spBjq9waSUCVfgwtEGXX5IC7rHrFEYOzE%3D&reserved=0
> >
https://eur02.safelinks.protection.outlook.com/?url=www.sdr-satellites.com&data=02%7C01%7Ccharlesh3%40msn.com%7C94e296aeab4d46e9585008d5391c08ba%7C84df9e7fe9f640afb435aaaaaaaaaaaa%7C1%7C0%7C636477714917915558&sdata=iFC3OooOhIgzG%2FwGquDP9VQWIt6H7tbCUzeaKeEcBrk%3D&reserved=0
> >
> >
> > -----Original Message-----
> > From: main@SDR-Radio.groups.io [mailto:main@SDR-Radio.groups.io] On Behalf
> > Of Leif Asbrink
> >
> > Well, I had some problems in the past, but today, with the latest drive
> > routines for the USB system I have no problem on any
> > USB3 port on any of my computers.
> >
> > I would be interested to know if you would have any problem running
> Perseus
> > with Linrad on a "problematic" USB port.
> >
> > If you think it would be difficult I would make an install video showing
> the
> > very few commands you need. Just tell me what OS you are using.
> >
> > 73
> >
> > Leif
> >
> >
> >
> >
> >
>
>
>
>
>
>
>
|
|
|
Re: HackRF Tuning Backwards
#hackrf
Ah Yes - Thank you.
I didn't realize that the Radio Definitions Invert spectrum checkbox made the Select Radio Invert spectrum checkbox visible.
Thanks. Much. Happy Camper
Dog Food On Its Way
|
|
|
Re: Default volume going to 100% when switching between satellites in the satellites list.
Hi Simon
Ah, that explains it
J
Thanks for getting back to me in your very busy schedule.
Neal
G1UQK
toggle quoted message
Show quoted text
From: main@SDR-Radio.groups.io [mailto:main@SDR-Radio.groups.io]
On Behalf Of Simon Brown
Sent: 01 December 2017 17:09
To: main@SDR-Radio.groups.io
Subject: Re: [SDR-Radio] Default volume going to 100% when switching between satellites in the satellites list.
Hi,
Added on purpose, pain it is, now no longer applied
😊 .
Hi Simon
Firstly, keep up all the good work. This is by far the best SDR program out there.
When I switch between satellites using the Satellites list the volume is automatically going to 100% no matter what level I choose while on a particular satellite. This would not normally be a problem but when you are using headphones in
a shared room it not only makes me jump out of my skin but also those around me. Is there a setting that sets a default volume per satellite?
I am also not sure when this started happening as I have not had chance to do anything with satellites for a while and I know you have released a few new versions since I last used it.
Also I am not sure if anyone else has reported this as I did try a search but it didn’t return any results that helped.
I know you usually need screenshots but wasn’t sure what screenshot you would need so I have added a screenshot of the main console with the volume at a lower level and a screenshot to show what satellite was selected. Then there is one
where I have changed the satellite and the last is the main console showing the volume at 100%
Not an urgent one but wanted to make sure it wasn’t a bug ;-)
All the best
Neal
G1UQK
|
|
|
Re: Connecting SDR Console V3's CAT to DXtreme11 Logging Software?
Simon Brown
toggle quoted message
Show quoted text
-----Original Message-----
From: main@SDR-Radio.groups.io [mailto:main@SDR-Radio.groups.io] On Behalf Of Nils Schiffhauer
Sent: 02 December 2017 14:42
To: main@SDR-Radio.groups.io
Subject: [SDR-Radio] Connecting SDR Console V3's CAT to DXtreme11 Logging Software?
Hi - after some hours, I still had no luck in connecting "SDR Console V3" to logging software "DXtreme 11b" via the CAT protocol
It only transfers the Mode from DXtreme to SDR Console, but not the frequency.
Anyone more luck, and how?
Thanks & 73 Nils
--
73 Nils, dk8ok.org
|
|
|
Re: HackRF Tuning Backwards
#hackrf
Simon Brown
toggle quoted message
Show quoted text
From: main@SDR-Radio.groups.io [mailto:main@SDR-Radio.groups.io] On Behalf Of James Brown
Sent: 02 December 2017 14:58
To: main@SDR-Radio.groups.io
Subject: Re: [SDR-Radio] HackRF Tuning Backwards #hackrf After long experimenting with both SDR# and CubicSDR (which both provide a way to swap I/Q) I am convinced that this is the problem with the HackRF driver. Is this something that could be fixed? I would much rather use SDR Console than either of these others Regards....... James Brown
|
|
|
Re: HackRF Tuning Backwards
#hackrf
After long experimenting with both SDR# and CubicSDR (which both provide a way to swap I/Q) I am convinced that this is the problem with the HackRF driver. Is this something that could be fixed?
I would much rather use SDR Console than either of these others
Regards....... James Brown
|
|
|
Connecting SDR Console V3's CAT to DXtreme11 Logging Software?
Hi - after some hours, I still had no luck in connecting "SDR Console V3" to logging software "DXtreme 11b" via the CAT protocol
It only transfers the Mode from DXtreme to SDR Console, but not the frequency.
Anyone more luck, and how?
Thanks & 73 Nils
--
73 Nils, dk8ok.org
|
|
|
Ruben Navarro Huedo (EA5BZ)
Hello Simon and Ground friends:
I am testing last 64 bits preview with CW Skimmer.
All is fine... IQ Data from SDR Console is going to CW Skimmer.
But i think CAT is running 50%:
Clicking on CW Skimmer waterfall --> Moves correctly SDR Console Frequency
But Moving SDR Console Frequency it doesn't move CW Skimmer
Is this Ok? Or.... do i have a problem?
Thank's a lot.
|
|
|
Re: YAESU FTDX 5000 TX MUTE ISSUES ON SDR CONSOLE
Simon Brown
Hi,
Not yet - busy elsewhere at the moment, sorry.
Simon Brown, G4ELI
www.dxgalaxy.com
www.sdr-radio.com
www.sdr-satellites.com
toggle quoted message
Show quoted text
-----Original Message-----
From: main@SDR-Radio.groups.io [mailto:main@SDR-Radio.groups.io] On Behalf Of Larry Schroeder
Sent: 02 December 2017 10:21
To: main@SDR-Radio.groups.io
Subject: [SDR-Radio] YAESU FTDX 5000 TX MUTE ISSUES ON SDR CONSOLE
Good Morning Simon,
Just wanted to follow up on the problem I’m having muting the receiver on the SDR Console here. I sent along the images you requested and wondered if you have any thoughts on what may be going on.
If you need the pics of the Omni Rig Client I’m going to include them again here. I’m hoping that this can be fixed so I’m able to use the SDR PLAY RSP2PRO with SDR CONSOLE.
If anyone else is running a Yaesu FTDX 5000 you might share how you have it set up with SDR CONSOLE as well.
Larry Schroeder
WD9SEF
715-574-5633. Mobile
WD9SEF@...
www.evelynfrechette.com.
Book and Movie Website
|
|
|
