|
Re: Lost cat control to external radio
Cody <kc2lsd@...>
So how does one make this happen? Last week my issues was I was running the wrong version of Omni Rig the corect one is 1.20 which is what I am running.
Thanks again but there has to be a solution Thjanks again Cody
|
|
|
|
|
|
Re: Lost cat control to external radio
Siegfried Jackstien
virtual comport may be a shared port .. one end to sdrc ... other end to omnirig dg9bfc sigi Am 05.07.2022 um 22:29 schrieb jdow:
|
|
|
|
|
|
Re: Lost cat control to external radio
jdow
I am thinking in terms of communications between OmniRig and
SDRC. Remember that you cannot open a com port and share it with
multiple applications. So you cannot connect SDRC to the radio's
comport and OmniRig to the radio's comport at the same time. {^_^} On 20220705 12:28:15, Cody via
groups.io wrote:
jdow thanks for the quick reply. My radio is using com 7, Yaesu installs two com ports one for rig control, in my case com 7 and com 8 sends data cw digital ect. So how can I use a virtual cable? Where do I set the VC in SDRC? I’m new to the realm of virtual anything. I thought I only need OmniRig Vrs. 1.20 which is what I have installed. I did have it working last week ago
|
|
|
|
|
|
Re: RDS decoding
Larry Horlick
I echo your observations, Paul. I have found EXACTLY what you describe. Larry
On Tue, Jul 5, 2022 at 5:21 PM Paul <paul@...> wrote: RDS decoding in Console is very good but always check reception a few times from recordings, I've lost count of the times I've played back a short section of reception and the PI code has popped up only once in 3 or 4 loops of the same recording. This has been observed not only on Console but Sharp too so it's always a good idea to replay the same bit of reception a few times in case you get lucky.
|
|
|
|
|
|
Re: RDS decoding
Paul
RDS decoding in Console is very good but always check reception a few times from recordings, I've lost count of the times I've played back a short section of reception and the PI code has popped up only once in 3 or 4 loops of the same recording. This has been observed not only on Console but Sharp too so it's always a good idea to replay the same bit of reception a few times in case you get lucky.
I'd also suggest running RDS Spy in conjunction with the VAC output because that will grab PIs when Console doesn't. Asymmetric filtering is another critical component to RDS decoding if there's QRM to one side of the wanted signal. One other trick that very occasionally causes a PI to pop up is to quickly switch between preset bandwidths like 150, 175 and 192kHz. Paul G7PUV G9PUV RX-888 MKII, Elad FDM-S3, RTLSDR820. Icom ICR8500, SDRPlay RSP1A, A*rspy. HS Publications D100 TV-DX receiver. Sony XDR F1, TEF6686 tuner, XDR-GTK. LNA4ALL, SV1AFN & CCW Multicouplers. W4KMA 18-100MHz custom Log Periodic. Wellbrook ALA1530AL1 active HF loop. Korner 19ele BII, Korner 19ele BIII. www.youtube.com/Aceblaggard 24 hour digimode log https://bit.ly/3xxUQA2
|
|
|
|
|
|
Re: Lost cat control to external radio
Cody <kc2lsd@...>
jdow thanks for the quick reply. My radio is using com 7, Yaesu installs two com ports one for rig control, in my case com 7 and com 8 sends data cw digital ect. So how can I use a virtual cable? Where do I set the VC in SDRC? I’m new to the realm of virtual anything. I thought I only need OmniRig Vrs. 1.20 which is what I have installed. I did have it working last week ago
-- Thanks you
|
|
|
|
|
|
Re: Lost cat control to external radio
jdow
With com0com or equivalent you get virtual cables that have two ends. If you try to open COM7 in SDRC and in OmniRig it's not going to work. Find the other end of COM7's virtual cable and have one of the two use it instead of COM7. {o.o} On 20220705 11:08:42, Cody via
groups.io wrote:
Sorry I thought I added this photo. When I try to open the external radio here what I get:
|
|
|
|
|
|
Re: Software installation
#rtl
jdow
SDRC is not designed to support side-by-side installations. A proper such design would not use the same registry and %apdata% folders for storing settings, thus making them truly independent of each other. SDRSharp does this if that is what you want. With this in mind a settings snapshot feature that archives all settings before the user gets into "experimental" mode might be a good thing. {^_^} On 20220704 23:25:13, Gord Seifert
wrote:
|
|
|
|
|
|
Re: Lost cat control to external radio
Cody <kc2lsd@...>
Sorry I thought I added this photo. When I try to open the external radio here what I get:
-- Thanks you
|
|
|
|
|
|
Re: Lost cat control to external radio
Cody <kc2lsd@...>
When I set up Omni Rig I am using the comport assigned to my radio "Com 7"
-- Thank you
|
|
|
|
|
|
Re: Remaining VAC Issue
I found the problem. The command 'Buffers' has been replace with 'BufferParts'. Any existing batch files need to be edited with this change.
Audio using SDR Console now sounds good.
|
|
|
|
|
|
Re: Remaining VAC Issue
Control Panel picture attached
|
|
|
|
|
|
Re: Remaining VAC Issue
Last night, I updated VAC from 4.15 to 4.67.
When I use my batch files (one file per VAC Line) to start Audio Repeater, I receive the error message as shown in an attached picture. This picture shows the error message and and the batch file as used in version 4.15. Documentation with VAC seems to indicate that nothing has changed from previous versions. Also attached is the VAC 4.67 Control Panel screen I do not see a way to correct this. I really don't want to revert back to the old version. Thanks for any help. George
|
|
|
|
|
|
Re: Lost cat control to external radio
Cody <kc2lsd@...>
Max I can't seem to find how to attach my photos. When I try to open the external radio it's looking for Omni Rig,that's SDRC contacts to my radio.
-- Thanks Cody
|
|
|
|
|
|
Re: Remote encoder
Don Woodward - KD4APP
I looked at that one - it says "multimedia" so I wasn't sure.
I found this one and also found out SDRConsole supports mapping keys to the functions - this one has programmable keys. For example, I could map the "T" key to TX in SDRConsole and then map "T" to a button on this. Also looks like you can map the arrow keys
to the shuttle to control the frequency.
73's
Don W.
KD4APP
From: main@SDR-Radio.groups.io <main@SDR-Radio.groups.io> on behalf of Alistair - M5ASF via groups.io <liverpudd@...>
Sent: Monday, July 4, 2022 5:16 AM To: main@SDR-Radio.groups.io <main@SDR-Radio.groups.io> Subject: Re: [SDR-Radio] Remote encoder Might one of these work: https://www.aliexpress.com/item/1005002989778143.html
|
|
|
|
|
|
Re: Remaining VAC Issue
Siegfried Jackstien
Maybe it does help setting the cables to a fixed 48 k sampling speed?!? (just a shoot in the dark) DG9BFC sigi Am 05.07.2022 10:11 schrieb "George Stein - NJ3H via groups.io" <nj3h@...>:
Hi Simon,
|
|
|
|
|
|
Re: Cached data
Yes,
the maximum cache size is 480MB, I'll increase this to the greater of 480MB and 1/8 installed RAM, so if you have 8GB it'll be 1GB, if you have 16GB it'll be 2GB etc.
From: main@SDR-Radio.groups.io <main@SDR-Radio.groups.io> on behalf of Simon Brown via groups.io <simon@...>
Sent: 04 July 2022 19:54 To: main@SDR-Radio.groups.io <main@SDR-Radio.groups.io> Subject: Re: [SDR-Radio] Cached data Depends on the same rate / bandwidth. There may be a maximum cache size which I can increase.
From: main@SDR-Radio.groups.io <main@SDR-Radio.groups.io> on behalf of Larry Horlick via groups.io <llhorlick@...>
Sent: 04 July 2022 19:17 To: main@sdr-radio.groups.io <main@sdr-radio.groups.io> Subject: Re: [SDR-Radio] Cached data I'm not getting the result with the data cache that I expected...
If I set the cache to 30s...and record for 30 seconds I should get a file with 60 seconds of data, correct? What I see is only 42 seconds. When I look at the logfile I see: Cached data...12 seconds. Should that not be 30 seconds?
Could someone play with this and report back...
Larry
On Thu, Jun 23, 2022 at 1:04 PM Simon Brown <simon@...> wrote:
-- - + - + -
Please use https://forum.sdr-radio.com:4499/ when posting questions or problems.
-- - + - + -
Please use https://forum.sdr-radio.com:4499/ when posting questions or problems.
|
|
|
|
|
|
Re: Remaining VAC Issue
Hi Simon,
toggle quoted messageShow quoted text
Thanks for looking at this issue. Would you be so kind to annotate on the VAC Control Panel picture which field or fields need updating and what a good value would be? Have a good Tuesday. Regards,
|
|
|
|
|
|
Re: Remaining VAC Issue
Thanks, it's flow control bursting. If possible, put a bigger buffer in the VAC I think.
From: main@SDR-Radio.groups.io <main@SDR-Radio.groups.io> on behalf of George Stein - NJ3H via groups.io <nj3h@...>
Sent: 05 July 2022 06:27 To: main@SDR-Radio.groups.io <main@SDR-Radio.groups.io> Subject: Re: [SDR-Radio] Remaining VAC Issue Forgot the DebugView file.
-- - + - + -
Please use https://forum.sdr-radio.com:4499/ when posting questions or problems.
|
|
|
|
|
|
Re: Lost cat control to external radio
Max
On Tue, Jul 5, 2022 at 01:33 AM, Cody wrote:
I had everyhtnig working well . Now when I try to run my external radio I get the Omni Rig fault. I using Omni 1.2 .https://www.sdr-radio.com/screenshot Max
|
|
|
|