|
Re: IQ File Error - "To much queued data"
#airspy
Bjarne Mjelde
Check that you have activated write cache on your disk. This should always be done when recording huge files like I/Q files.
-- Bjarne Mjelde arcticdx.blogspot.com Remote rx: arcticsdr.proxy.kiwisdr.com:8073/ |
|
|
|
Re: Visual gain: no change when changing level (?)
Thank you again, Simon!
73 de Gaspar, EA6AMM |
|
|
|
Re: Visual gain: no change when changing level (?)
Hi,
This *is* a bug in the console, I’ve detected very old firmware but am not processing visual gain correctly.
Newest firmware is always good.
Simon Brown, G4ELI
From: main@SDR-Radio.groups.io <main@SDR-Radio.groups.io> On Behalf Of ea6amm@...
Sorry Calder, i didn't see your message on time! |
|
|
|
Re: Visual gain: no change when changing level (?)
Sorry Calder, i didn't see your message on time!
I just found the download page for Airspy Hf + firmware. I will update and try again with the Visual Gain on SDRConsole V3.03. 73 de Gaspar, EA6AMM |
|
|
|
Re: Visual gain: no change when changing level (?)
Hi, Petr,
It's possible. I downloaded the RTL SDR software for AirSPY HF + on October 16 for the first time, and since then I haven't checked for firmware updates... as I don't know how to do it, or how to check which version I have (?) When I open the SDR-RTL program I get SDR# v. 1.0.0.1672, and when I check on "Radio" I can see Firmware R1.00.00 Would you please help me with this? If it is off topic, please, drop me a mail at my allsign at gmail dot com Thank you very much! 73 de EA6AMM Gaspar |
|
|
|
Re: Visual gain: no change when changing level (?)
Calder Latham
The latest Firmware for Airspy HF+ is R1.7.2
toggle quoted message
Show quoted text
W1HHO All the Best. From the woods of Maine. On 12/12/2018 09:07, Petr Šlehofer via
Groups.Io wrote:
I think you only have the old firmware in Airspy HF+. |
|
|
|
IQ File Error - "To much queued data"
#airspy
Ivan Abilev
Hello dear friends! I am a beginner here. I faced a problem in attempt of the record IQ of the file.
My equipment - Airspy Mini 6.0 MHz.
Got an external hard drive of the ADATA HD330 4TB brand. Connection through USB 3.0 slot writing rate 100mb/S reading speed 150mb/S.
The program persistently does not want to write the IQ file directly on a disk. After several minutes of record the error "To much queued data, removed 500 packets, 15000000 samples, 115 megabytes" Error jumps out can leave at once at record and can write 10-30 minutes and jump out then. Writing rate within the first minute is lower than necessary. The start from 21.5 MB \with and slowly rises to 23.7-23.9mb and then to necessary 24.0mb. At record of a band 3 MHz are observed the same problem. Record within the first minute 10.2-11.8mb/with and in the second third minute reaches necessary 12mb/with
This error is not observed on the built-in disk C with the operating system, there record goes without problems. My Windows 10 system, 64bit. ASUS x541nc, NVIDIA GeForce 810m, 4GB. There are enough resources of the laptop for start and comfortable work with Airspy and a band 6 MHz. Did the following actions which did not help me.
1) Defragmentation of a disk
2) Deep formatting of a disk
3) Capacity of the USB bus is enough work for Airspy + HDD and two flash cards.
2) Reinstallation of a system
3) Change of USB with 3.0 on 2.0
4) Put the old version of the program.
Please, prompt in what a problem? What else can be made? I put to the subject Log file.
P.S Forgive to for errors, I write not in a mother tongue |
|
|
|
Re: Visual gain: no change when changing level (?)
Petr Šlehofer
I think you only have the old firmware in Airspy HF+.
I have firmware R1.6.5 2018-03-23 and the same configuration and it works. |
|
|
|
Re: Visual gain: no change when changing level (?)
Thank you for your answer, Simon!
73, Gaspar, EA6AMM |
|
|
|
Re: Frustrating
Mikael Dagman - SA6BSS
After another update and restart the problem was back so I tried the sugested fix and disabled agc and it started up fine, tnx for the heads up! :)
|
|
|
|
Re: Visual gain: no change when changing level (?)
toggle quoted message
Show quoted text
From: main@SDR-Radio.groups.io <main@SDR-Radio.groups.io> On Behalf Of ea6amm@...
Just in case, as the kid of the signal I took for the captures before graphically changes a lot by its own nature, here I'm attaching two more: |
|
|
|
Re: Frustrating
R D
I did the above and V3 still would lock up with the RSP 2.
I then under Tools selected the Registry button and just deleted the entry in the registry for SDRplay. Restarted V3 and everything is now working fine. As always use caution while in the registry. Be interested in hearing if this works for anyone else. Rich, WD3C |
|
|
|
Re: WRTH BAwards 2019
Hiya Mike,
I have the Airspy HF+ along with the SDRplay RSP2 & RSPduo. All are good HF receivers in my experience which is 99 44/100 of my listening. But the receiver I'm having the most fun with at the moment is my KiwiSDR. Just wish conditions were better. :( The Kiwi allows me to hear signals in LW that the others can't sort out of the noise. Another excellent piece of kit. -- Mike On 12/11/18 3:46 PM, MadMike wrote:
|
|
|
|
Re: WRTH BAwards 2019
Hasan Schiers N0AN
Also, in my testing here, the AirSpy HF+ has been VERY vulnerable to desense/intermod from my 70cm Tx on 2m satellite downlinks. I have a filter in front of the SDR to keep 70cm out of 2m...well, the Airspy HF+ still doesn't like it. Every time I key on 70cm, the 2m rx gets trashed...spikes, you name it. Using the exact same cables, antenna, etc, but changing to EITHER: SDRPlay RSP2 or FunCube Pro + SDR eliminates the problem. There is not a hint of desense or intermod/overload on either of them when listening on 2m and tx'ing on 70cm. So, while the AirSpy HF+ is wonderful on HF (I have used it a LOT), it doesn't cut it for full duplex satellite work....at least not here. 73, N0AN Hasan On Tue, Dec 11, 2018 at 2:46 PM MadMike <virtualtrains@...> wrote:
|
|
|
|
Re: WRTH BAwards 2019
agene
Although the Airspy HF+ is a good little receiver, well made and it cheap, hence 'Best value'. I don't consider a SDR with a max bandwidth of 768kHz to be anything like the 'best available SDR' in this day and age when 10MHz bandwidth is pretty common and twice that is available.
|
|
|
|
Re: Supplier experience
D R
Hi Tracey, I took all that into account, and it's still cheaper than buying from Moonraker. I've also been hit for customs charges by Royal Mail in the past on stuff coming via ordinary mail, so it's just pot luck whether you get stung or not. I just decided to go for speed and certainty, which you get from DHL - but then ITEAD took two and half weeks to send it! In ordinary post it could be another 2-4 weeks before it arrives, then there's Xmas delays to consider ... Regards, Dave.
On Tuesday, 11 December 2018, 15:25:13 GMT, Tracey Gardner via Groups.Io <tracey.gardner@...> wrote:
The only drawback with using DHL to delivery from Itead into the UK, is that you get hit by import duty and handling charges?
Using the postal method has incurred none of those charges for any of the Airspy products that I have ordered from Itead.
Thus resulting in an HF+ for around £150 into the UK.
Regards
Tracey G5VU
|
|
|
|
Re: Supplier experience
And some carriers often demand the exact amount of cash before handing over the goods (no change given). Allan G3PIY From: main@SDR-Radio.groups.io
[mailto:main@SDR-Radio.groups.io] On Behalf Of Tracey
Gardner via Groups.Io
Sent: 11 December 2018 15:25 To: main@SDR-Radio.groups.io Subject: Re: [SDR-Radio] Supplier experience
The only drawback with using DHL to delivery from Itead into the UK, is that you get hit by import duty and handling charges? Using the postal method has incurred none of those charges for any of the Airspy products that I have ordered from Itead. Thus resulting in an HF+ for around £150 into the UK.
Regards
Tracey G5VU
|
|
|
|
Re: Supplier experience
Tracey Gardner
The only drawback with using DHL to delivery from Itead into the UK, is that you get hit by import duty and handling charges?
Using the postal method has incurred none of those charges for any of the Airspy products that I have ordered from Itead.
Thus resulting in an HF+ for around £150 into the UK.
Regards
Tracey G5VU
|
|
|
|
Re: SDR Console w/Lime SDR - Case Study
#limesdr
#sdrconsolev3
Gareth,
Only the test team have access to the TX features. Some background information is available on https://www.dit-dit-dit.com/.
At the moment I’m having problems with the Lime API support, more time is needed before I can perfect the transmit support for amateur use.
Simon Brown, G4ELI
From: main@SDR-Radio.groups.io <main@SDR-Radio.groups.io> On Behalf Of freelance@...
Hi, |
|
|
|
Re: Supplier experience
D R
Hi Ingolf - I got mine as well, after sending them another query last night. I paid for DHL shipment, and their website shows that they have received it from ITEAD, so I might receive it in a few more days. Regards, Dave
On Tuesday, 11 December 2018, 08:00:12 GMT, sm6fhz <ingolf.fhz@...> wrote:
Hi all. I got an shipping note from ITEAD this morning, including a tracking number, on the Airspy HF+ I have been chasing them about. So, now just to wait and keep fingers crossed it will make it here for X-mas :-) Have you got a shipping note as well Dave? 73 / Ingolf, SM6FHZ |
|
|