I run an external radio via Omni-rig no problem and another program via the CAT controller section all usually runs fine. Sometimes I get a similar problem to you when using a VSP for the connection.

On Sun, Aug 30, 2020 at 09:13 PM, Jack D. Generaux wrote: Log4OM manualI don't use Log4OM but surely it's connection to SDR Console should be through the CAT controller section and not through

The page layouts are in the registry. That would be nice to save. At least I'd want that. {o.o} On 20200830 22:50:12, Simon Brown wrote:

I noticed a few other places that seem to be tied into the issue. Getting them all without the benefit of knowing the inwards of SDRC would be "risky". (And John Williams (Star Wars)

In fact the registry info isn’t needed! In practice I can support an unlimited number of identities, I just show a maximum of 9. Simon Brown, G4ELI https://www.sdr-radio.com

Programmers never retire, they just decompile 😊 . Moving / copying identities would not be too hard, it’s a case of copying files and a registry tree. Simon Brown,

I do not think this could be done without a lot of work. (I could "probably" facilitate this with some work with C++ and Visual Studio; but, I lack the incentive. And it would be on a

I have been able to use my Hermes-Lite with SDR-Radio, and WSJT-x but unable to get the link through Omni-Rig to Log4OM. I hvae tried running with Administrator provileges for SDR-Radio, Log4OM, and

I would like to save my Main identity (with all of my virtual radios and so on), so that I could later load that saved identity into one of the four alternative. That way I could change the Main

Thank you Jim, tried. it works! Grazie Carlo

https://air-radiorama.blogspot.com/2020/08/adalm-pluto-rx-in-odd-harmonic-mode-at.html Adalm Pluto Local Oscillator is square wave , it is possible to use it in odd harmonic mode . Here is shown

I have a couple questions about the CAT control. 1.) With regard to setting the receiver mode via CAT, how do you choose AM? AM is not listed as a supported mode in the CAT control documentation.

OK, here's what 100W on 75M looks like. Conditions: IC-7300 on Inverted Vee at 90' with 100W in LSB. SDR antenna inverted Vee ~150 at the closest point. Initially it's incredibly wide (all 760kHz of

Listen while TX? As mentioned above, the time delay going to your headset while you talk or send CW will drive you batty! A random length wire attached to the SDR, and the AS-RXFEP in line will be

On Fri, Aug 28, 2020 at 08:19 AM, Kriss Kliegle KA1GJU wrote: For front end protection, I use this one on KA1GJU Super Station #2 (with 4 SDR's) and the KA1GJU @ PCARC servers due to the proximity of

Hello, If you have a feature suggestion/request, please post it here: https://forum.sdr-radio.com:4499/viewforum.php?f=53 Thanks.

Considering that the Pluto receives also in harmonic mode , being the oscillator square wave , I would like to suggest to put in Console the possibility to have ( like in Satsagen ) an harmonic way on

I have produced this , including two videos ,for rough instrumental measurements of the ADALM PLUTO on the TX ( till 26.5 GHz ) and RX ports

On 20200829 20:32:58, Bob Dengler wrote: Gee, I homed in on the magnesium chassis. I almost missed the 30 years operational lifetime.... Riiiiight. It's only warranted for 1 year and by

On 20200829 20:32:58, Bob Dengler wrote: That might be nice for a backpack, if you were mildly suicidal. It is VERY much not what you want for work on your desk. You want heavy, solid