Thanks Sigi. But then why offer 9 bandwidths from 500kHz to 10 MHz, if the performances are the same? There is necessarily something that changes depending on the bandwidth, but what? 73, Michel

Hi, Standalone isn’t yet supported. It’s next on my list – my development DUO broke and I only just got it back from ELAD. Simon Brown, G4ELI https://www.sdr-radio.com

Sorry, don't have Elad so not sure and don't see anything obviously incorrect but in meantime before you get a definitive answer, did you check out all the information on this

The FDM-DUO works in stand alone mode as it should. I have installed the ELAD FDM-SW2. RX ist fully working but TX audio is missing. I could not figure out the problem, but anyway, my goal is to use

Hello Siegfried, Monday, February 14, 2022 Right, sorry, I am afraid I cannot understand how this would, or perhaps even should, work. Let us assume I have the relay board in my Pluto. The Pluto

On Tue, Feb 15, 2022 at 07:33 AM, Simon Brown wrote: I think this is a bug – if Mute is checked then selecting a new Favourite should no unmute – at least, that’s how I remember it Simon In the

Hi , I want to show the spectrum if I work RTTY with my K3. Environment is RSPdx, K3 and SDRconsole. As far as I work with USB, CW and .... -Mode evering is fine, but in case I want to got into

Max, I think this is a bug – if Mute is checked then selecting a new Favourite should no unmute – at least, that’s how I remember it 😊 . Simon Brown, G4ELI https://www.sdr-radio.com

Thanks Max. In the end, all I did was select a built-in favorite, muted the speaker on the receive window then clicked "Update" then "OK", saving that favorite with the now muted speaker. I did this

sometimes ... yes have a nice evening old lady :-) Am 15.02.2022 um 01:15 schrieb jdow:

Michel, Thank you for the offer. My intent was to have the band plan be for the US/ITU region 2. The band plan provided with the beta appears to be ITU region 2. The overlapping band plans are

I suspect that if you check it out Simon's 2.8 kHz filter is narrower than a conventional crystal filter's 2.7 kHz even at 30 dB down. {^_^} On 20220214 08:31:46,

Agreed - and stubborn, too. {^_-} On 20220214 05:36:54, Simon Brown wrote:

On Mon, Feb 14, 2022 at 04:40 PM, <w3wtw@...> wrote: I did this "Ribbon bar, Favourites, Settings, Selection" but the volume keeps unmuting at ever Favorite band change. The "Apply Mute" doesn't seem

On Mon, Feb 14, 2022 at 04:40 PM, <w3wtw@...> wrote: I did this "Ribbon bar, Favourites, Settings, Selection" but the volume keeps unmuting at ever Favorite band change. The "Apply Mute" doesn't seem

for the brave is either the 303 version ... or my 2103 (came out about 2 weeks after the 303 version) the ts modulation is the same thing .. and as far as i know both support the relay out of the

Hello Siegfried, Monday, February 14, 2022 It modulates the TS, as far as I understand it. The BATC (British Amateur Television Club) who apparently developed the device state that ONLY the

Hi all. Lightly used G31DDC Excalibur with VSC software included. Includes original packaging, software, manual, NA Power adaptor, data cable and SMA adaptors (female to female) for BNC and SO-259).

I can save my Memories with muted volume but moving from the built in Favorites band by band and the audio keeps unmuting. I did this "Ribbon bar, Favourites, Settings, Selection" but the volume

... i am also sometimes hard to you with my mails (too much info) ... or sometimes are missunderstood from you but its fun helping others with their setup ... i need such positive feedbacks ... that