Hi, I’ll try to remember exactly what the idea was. This part of the code must be ~6 years old, certainly from the early days of V3 when I was learning a great deal very quickly. Simon

I've found my version no ground to USB and no way of knowing the modification as all information on the internet gone. An easy way is no BNC connected if there is noise earth usb and BNC and it

maybe cpu load is different keeping several recording running in parallel or one bigger (needs for sure a fast ssd and/or a hefty cpu)... same with analyzing them ... ... in fact i can not

On Sun, Feb 13, 2022 at 01:20 PM, michel soldevila wrote: Hi group, A very basic question, sorry: with SDR Console, I could record the I and Q signals over the full bandwidth of my RSP-2 SDR, i.e.

Thanks Sigi. But then why offer 9 bandwidths from 500kHz to 10 MHz, if the performances are the same? There is necessarily something that changes depending on the bandwidth, but what? 73, Michel

Hi, Standalone isn’t yet supported. It’s next on my list – my development DUO broke and I only just got it back from ELAD. Simon Brown, G4ELI https://www.sdr-radio.com

Sorry, don't have Elad so not sure and don't see anything obviously incorrect but in meantime before you get a definitive answer, did you check out all the information on this

The FDM-DUO works in stand alone mode as it should. I have installed the ELAD FDM-SW2. RX ist fully working but TX audio is missing. I could not figure out the problem, but anyway, my goal is to use

Hello Siegfried, Monday, February 14, 2022 Right, sorry, I am afraid I cannot understand how this would, or perhaps even should, work. Let us assume I have the relay board in my Pluto. The Pluto

On Tue, Feb 15, 2022 at 07:33 AM, Simon Brown wrote: I think this is a bug – if Mute is checked then selecting a new Favourite should no unmute – at least, that’s how I remember it Simon In the

Hi , I want to show the spectrum if I work RTTY with my K3. Environment is RSPdx, K3 and SDRconsole. As far as I work with USB, CW and .... -Mode evering is fine, but in case I want to got into

Max, I think this is a bug – if Mute is checked then selecting a new Favourite should no unmute – at least, that’s how I remember it 😊 . Simon Brown, G4ELI https://www.sdr-radio.com

Thanks Max. In the end, all I did was select a built-in favorite, muted the speaker on the receive window then clicked "Update" then "OK", saving that favorite with the now muted speaker. I did this

sometimes ... yes have a nice evening old lady :-) Am 15.02.2022 um 01:15 schrieb jdow:

Michel, Thank you for the offer. My intent was to have the band plan be for the US/ITU region 2. The band plan provided with the beta appears to be ITU region 2. The overlapping band plans are

I suspect that if you check it out Simon's 2.8 kHz filter is narrower than a conventional crystal filter's 2.7 kHz even at 30 dB down. {^_^} On 20220214 08:31:46,

Agreed - and stubborn, too. {^_-} On 20220214 05:36:54, Simon Brown wrote:

On Mon, Feb 14, 2022 at 04:40 PM, <w3wtw@...> wrote: I did this "Ribbon bar, Favourites, Settings, Selection" but the volume keeps unmuting at ever Favorite band change. The "Apply Mute" doesn't seem

On Mon, Feb 14, 2022 at 04:40 PM, <w3wtw@...> wrote: I did this "Ribbon bar, Favourites, Settings, Selection" but the volume keeps unmuting at ever Favorite band change. The "Apply Mute" doesn't seem

for the brave is either the 303 version ... or my 2103 (came out about 2 weeks after the 303 version) the ts modulation is the same thing .. and as far as i know both support the relay out of the