a hint ... use TWO virtual cards .. one for rx and one for tx (example vb cable a and b) dg9bfc sigi Am 26.02.2022 um 21:55 schrieb Douglas Pervine:

wrong ... for tx into console you can use a few ways via virtual comport ... (depends what packet software you use) or with using vox (that works for sure) then sdr console will switch

VOX should work – add a screenshot of the whole console. Simon Brown, G4ELI https://www.sdr-radio.com

Easier said than done. The problem is keying PTT. SDR software doesn't have a way to PTT transmit on and off. and/or SDR devices (i.e. LimeSDR Mini / Adalm-Pluto) can't accept a PTT. Transmit is a

Hi Mark, exactly we have several new foundation licence holders and QTH of some club members S9+ noise. Finances may mean a Frankenstein rig for some. The Dow key will take 100watts? I've been playing

the si5323 has some high phase noise ... not?!? dg9bfc sigi Am 25.02.2022 um 20:47 schrieb Larry Dodd:

or "spread the elbows" a bit to have some room ... they splatter as wide as a barn door that nobody may sit next to them (and splatter in their passband) dg9bfc sigi Am

You don't know anything about contesting. :-) They want the dirtiest signal possible to keep the enemy at arms length. Bob - wd6dod On 2/25/2022 10:22 PM, jdow wrote:

Daniel, My first ham station consisted of an 897 for transmit, a FUNcube Pro Plus dongle and SDRC (running on a 40 inch 4k screen) for receive, a single G5RV shared between the 897 and FCPP, and a

The 7300 is a relatively affordable radio, Personally I use an sdr switch box and cat rig control with local SDR or even websdr. Different strokes for different folks. Omnirig and an sdr switch and

Excellent! Conrad From: main@SDR-Radio.groups.io <main@SDR-Radio.groups.io>On Behalf Of Simon Brown via groups.io Sent: 25 February 2022 20:37 To: main@SDR-Radio.groups.io Subject: Re:

Glad to be of service! I experience that same phenomena from time to time. Especially with flashes of nostalgic thoughts. Larry K4LED ------------ K4LED

It may be an internal powersupply that takes 13.8 VDC down to 5 VDC. In that case there is no help for it without significant surgery. {^_^} On 20220225 11:49:05,

I have a SICK SICK mind. You made a broad statement and my head wondered if the 24 caret Gold Plated CW Key was all that absurd. I experienced my typical blur of possibilities fly

I am not sure why contesters at multi-op stations don't use rigs with the best TX signals they can get. With adequate antenna separation you can place more operators on the same band.

Start as clean as you can achieve then use PS if it is available. Both right. There is no single perfect correct way. Judiciously combine methods to make it better. (Wash hands,

I was with you until that last snipe. It appears the 7300 MAY have a problem. If it has spurious at -3db from full output that are only 60 dB down removed 20 kHz and 100 kHz from the

if you can mary an sdr software together with a packet software via virtual audo cable then it is all you need an sdr (hardware) like an rtl dngle .. or whatever an sdr software (be it

I've been using SDR's for a couple years now, but I still consider myself a beginner. I would like to use an SDR to transmit/receive AX.25. Ideally, it would be great advantage to use Direwolf. Is

I have the 16bit ANAN-10. Thanks, Mike N2MS