I can not get the External Radio panel to come up, it just keeps coming back to the Restart panel. Joe N9VX

Hi Max – Yea – it’s a blast for sure… Totally enjoy the SDRCv3 front end to tell you the truth. I had the FDM-DUO and the HL2 already. The FDM-DUO is my portable as I could operate it

Yes, I take all your points. Personally (and each to their own) now I've sampled pure SDR I don't see the point of running two radios in tandem when just the SDR does such a spectacular job. If I was

Joe, I am using the External Radio feature with my TS-590. The setup should be the same for your TS-590SG I believe. I think you have installed Omni-Rig already, if not you need to do so. Then just

Hello I use omirig and sdrc..works a treat.. As far as i know sdrc will NOT control your rig, thats what omirig is for. ( unless Simon has built in his own version in the last build or two.) Simon

Hi Max – I did order another HL2 to bring out the RX port, and basically deadend the TX PO issue. So that was already in the mix…J1/J21 location is the plan. I’m looking at the “ it lost its

Hi Tom I'm not familiar with using HL2 in this way, but used as a standard SDR (which effectively I think you are - albeit tracking the 101) you can disable the HL2 PA in SDRC. Perhaps that's not

Update... I am now using the serial port out of the TS-590SG instead of the USB port and the results are the same (SDR Console does not read radio frequency, but does receive by tuning SCR

I’m using SDR Console v3 with OmniRig on my FTDX-101D to allow me point and click freq changes, mouse scroll and the much nicer spectrum/waterfall/pana display from my Hermes Lite 2fed from the RX

I’m using SDR Console v3 with OmniRig on my FTDX-101D to allow me point and click freq changes, mouse scroll and the much nicer spectrum/waterfall/pana display from my Hermes Lite 2fed from the RX

Can not get the TS-590SG to change frequency in SDR Console 3.1. The receive works fine (and beautiful display), can change in SDR Console. If I run the test in Tools/Options I can change the

Frank, I thought you have fixed the problem? I have not been following your freeze thread. Simon Brown, G4ELI https://www.sdr-radio.com

HIHIHI.... ;-) After cleaning .... :-) were you able to verify the sequence of the problem at the frequency I listed for you? 73 Frank

Hello Max, Thursday, September 9, 2021 Thanks, I have read that thread and this from Simon sounds (pardon the pun...) good: "I rely on the input source to provide data at 48kHz, it's a simple

Just for info, there has already been a long conversation on exactly this topic about three weeks ago! https://forum.sdr-radio.com:4499/viewtopic.php?f=15&t=1308 Max

Per the tech spec sheet, that ARINST only has a max input signal strength of -35dBm, so anything over S9+40 might let the magic smoke out! Think I'll hafta pass.. Mark

I think being an early adopter of any product is taking a chance, but this one sounds like it has a lot of potential. There are a growing number of SDR offerings out there as you say; maybe this is

I did not have a cut and paste example for audio in. The same technique should work either way. You fill out the list just before it displays with then current values. {^_^}

it is the audio in device not audio out .... dg9bfc sigi Am 08.09.2021 um 22:56 schrieb jdow:

I would suggest that is an easy issue to fix. ON_CBN_DROPDOWN( IDC_RX_AUDIO_OUT_SEL, &CAudioControls::OnDropdownRxAudioOut ) with the OnDropdownRxAudioOut function rereading the list