Even programmers sleep… FWIW It’s running quite well with the 8000DLE but there are a few bugs being ironed out of the 8000DLE’s firmware (not by me). Simon Brown,

Ryan, What problem? I honestly don’t remember the previous thread. Without logfiles etc. I have no idea what’s happening. I’ll invite you to the test team where we’re using much newer

It can’t get the dongle started to find the list of sample rates. Can you discover the dongle or is this an old definition? Simon Brown, G4ELI http://sdr-radio.com

Barry, I figured it was something like that. I am guessing the website version supports 10.2. Thanks for the response. I have a homebrew apache hermes here built from a bare board with homebrew

Hi Ryan, We will have to wait for Simon to comment on what Hermes support he may added to V3 since he released preview 5a. I'm using a test release. On a positive note -- the next preview should

Here's my lime at 25Mhz wide on HF... Some great signals ​ Paul Jones - NN4F Ridgeville, SC EM93TB Email: paul@... Facebook.com/groups/sdrplay

Well the lime is working quite well on HF here, not perfect, but it works, did you get a secon batch that was modified ot did you modify your own? There are some broadcast FM images on HF, still, but

Hello, I started playing around with the LimeSDR. So, far not really impressive. I Tried using the Noolelec up convertor but has poor performance compared with the QSR1 16 bit A/D direct sampling

Barry, Yes i tried it with thetis first. Works just fine. Sdr console freezes after about 5 seconds. I am using preview 5a from the website. I don't see anything newer. Ryan KK6DZB

Hi Ryan, I updated my ANAN-10 with v10.3 (Protocol 2) and it works with the V3 Console (Apr 23, build 757). Have you tried it with Thetis? Barry WB2ZXJ

Simon, I am bringing this back from the dead. I have updated to the latest protocol 2 firmware 10.3 for the anan 10 and 100 16 bit hermes (not 10e or 100b) and I am having the same problem. I know

Tried Version 3 of SDR Console today and now wanting to goback to Version 2 however even after adding the xml registration, Version2 won't un-grey the Start button for selecting the RTL dongle ...

Hi Mike You’re quite right. I’veassumed the loss shown on the Lime graph is mainly due to the transformer. The Lime “Easyfix” graph shows-20dBfs dropping to -80dBfs at 1MHz, with -30dB at

Hi All, the subject got me thinking about an anomaly many must have seen regarding this and the ppm adjustment ; < rant > IF my understanding is correct, then in terms of a linear equation of the form

Hello, Does SDRConsole version 3 have a receive frequency offset to adjust for an up convertor? I thought I saw the adjustment before; but now I cannot find it. Sorry if this question has been asked

OK, got it. Checked the wrong box. Thanks, Paul! Mark Lunday, WD4ELG Greensboro, NC FM06be wd4elg@... http://wd4elg.blogspot.com SKCC #16439 FISTS #17972

Yes, IF out. Thanks Paul! Still same behavior. I shall continue to tinker. Everything was working on my other PC until the hard drive crashed over the weekend. Mark Lunday, WD4ELG Greensboro,

In the startup panel, select definitions and Invert spectrum, use this if using IF output Paul - NN4F Paul Jones - NN4F Ridgeville, SC EM93TB Email: paul@... Facebook.com/groups/sdrplay

New computer, SDR Console V3 Feb 2017, TS480SAT, using IF output. When I tune the rig VFO, SDR Console follows. I included a slight calibration correction, and I can monitor SSB and CW. But the

Yes, it's in the startup panel and click on definitions... Paul - NN4F Paul Jones - NN4F Ridgeville, SC EM93TB Email: paul@... Facebook.com/groups/sdrplay