main@SDR-Radio.groups.io

Re: How To: Connect to Pluto via Ethernet (Network)?

Dear all. Gisle ! I have tried a number of different Static Routs in my router but it did no difference at all to my issue. The Pluto is still not visible outside it's own sub-net. But I tried

By sm6fhz · #68289 ·

IQ 'Rewind/Replay' feature (?)

Greetings All Desired feature : IQ replay, a continuous loop circular buffer of (?) seconds of recorded IQ a) choose a frequency : current, memory selection, favorite selection, etc b) select a

By N8CVW · #68288 ·

Re: [Read me] The GPU load when using the SDR console is too high!?

I write my own windows controls and implement the drawing in Direct2D, examples are the waterfall, spectrum, Mode & Filter buttons, Audio display etc. You have far better tessellation and effects in

By Simon Brown · #68287 ·

Re: How To: Connect to Pluto via Ethernet (Network)?

There are two ways to route from 192.168.2.xxx to 192.168.3.1. One is set netmask to 255.255.254.0, 1111111 11111111 11111110 00000000. Then when a boolean "and" on the netmask and the

By jdow · #68286 ·

Re: How To: Connect to Pluto via Ethernet (Network)?

255.255.255.0, or 1111111 1111111 11111111 00000000 in binary, means that in terms of addresses 192.168.3.10 is on a different "network" (for routing purposes) than 192.168.2.10. Addresses

By jdow · #68285 ·

Re: How To: Connect to Pluto via Ethernet (Network)?

Hi Gisle. I will try to set a "Static Route" in my router. It does not look the same as your example as it is of another brand (Ubiquity, Edge-Router Lite) but I will try to find it. Your 10.0.0.1 is

By sm6fhz · #68284 ·

Re: Calibrating frequency of SDR radios

Some SDRs may load the system differently than others. And it's REALLY difficult to sort that out. SDRs are not really well suited to multi-threading, a usual technique to offload

By jdow · #68283 ·

Re: How To: Connect to Pluto via Ethernet (Network)?

Hi Joanne. Thanks for your answer. As you might have understood, I am not fluent in Ethernet Networking :-) I have the same Netmask 255.255.255.0 in both the Pluto and the router as well as the

By sm6fhz · #68282 ·

Re: Calibrating frequency of SDR radios

Thanks for explaining! Dropped USB packets should not make the difference between SDR players when I do the calibration on the same PC and on the same OS. Correct?

By Dirk · #68281 ·

Re: [Read me] The GPU load when using the SDR console is too high!?

So did you basically rewrite MFC to do this or just the owner draw features of the GUI? {^_^} On 20220924 21:12:02, Simon Brown wrote:

By jdow · #68280 ·

[Read me] The GPU load when using the SDR console is too high!?

So, For anyone who's interested the article below compares GDI (old) with DirectX / Direct2d (latest and greatest). After reading this you'll understand why new code generally uses Direct2D or

By Simon Brown · #68279 ·

Re: polgarjozsef@microweb.hu

I think this is a problem with groups.io - I removed the user from the group, there's no-one with that address but still e-mails are being sent there. Simon

By Simon Brown · #68278 ·

Re: The GPU load when using the SDR console is too high!? #sdrconsolev3

Well, Console is using 11% of the GPU's capacity which is not bad. SDR Console uses Direct-X which is a hardware-accelerated graphics system unlike GDI/GDI+ used by SDR Console v2, SDR# and SDR Uno.

By Simon Brown · #68277 ·

Re: The GPU load when using the SDR console is too high!? #sdrconsolev3

He might also check if the GPU is heavily throttling in a notebook configuration. {o.o} On 20220924 08:25:10, Simon Brown wrote:

By jdow · #68276 ·

Re: Calibrating frequency of SDR radios

The ideal answer is each front end requires one PPM value that each SDR software must explicitly load into the front end each time it is run. This PPM value should then be good at all

By jdow · #68275 ·

Re: FunCube Dongle ProPlus noise and RFI improvements. Tips please.

Should have said "through" instead of around. {o.o} On 20220924 04:01:07, jdow wrote:

By jdow · #68274 ·

polgarjozsef@microweb.hu

If he does not stop microweb.hu from spamming me with bounces microweb.hu will permanently as in forever will be trimmed off my email stream and not even placed into my spam bucket.

By jdow · #68273 ·

Re: The GPU load when using the SDR console is too high!? #sdrconsolev3

what waterfall resolution and speed?? dg9bfc sigi Am 24.09.2022 um 17:15 schrieb dl4ycc@...:

By Siegfried Jackstien · #68272 ·

Re: The GPU load when using the SDR console is too high!? #sdrconsolev3

It's very probably browser services. Simon Brown https://g4eli.com https://sdr-radio.com

By Simon Brown · #68271 ·

Re: The GPU load when using the SDR console is too high!? #sdrconsolev3

Thank you for the info. I will continue to monitor the GPU load and hope that the GPU load will eventually go down. -- vy 73 Klaus de DL4YCC

By dl4ycc@... · #68270 ·

Messages