Hi Sigi, The UBX board in the X310 has a max theoretical bandwith of 160MHz. At 50MHz Bandwith (max BW I can set in SDR console) I see about 14 to15% load on the 10G link, but the GTX 1650 gets

at first .. near every transceiver runs cleaner with lower power setting :-) if the tx signal (after internal mixing in the trx chip) is given out at a bigger level ... and a few mixing

Hi all, I often read the recommendation to operate the Pluto at lower output level and use external amplification if applicable. Can anybody please explain why the output signal of the Pluto should

Hi Christopher, thanks. Yeah, I have firewall settings for both private and public (and domain) set to off on all my PCs. No other wired machines inside or outside my network have issues connecting.

yepp ... the tx boost does only "hurt" the signal quality (so in my view could be deleted ... similar as the "offset tuning" ... that also only produces confusion (and an unwanted carrier if

Sigi, In the Pluto options there’s a page for the FIR Filter. The extra boost I added causes the problems – disabling this had a big effect, also tidying up some other filters helped. Simon

i did that ... (and answered) USE LOWER POWER TO HAVE A CLEANER SIGNAL!!!! (i can not pray that often enough) dg9bfc sigi Am 04.02.2022 um 01:14 schrieb Max:

Folks, can someone (Sigi?) please take a look at Rolf's post on the Forum: https://forum.sdr-radio.com:4499/viewtopic.php?f=71&t=1588 73 Max

10 g fibber for an sdr?? wow ... what bw are you using the ettus?? dg9bfc sigi Am 03.02.2022 um 21:33 schrieb Charly DF5VAE:

Hello All, finally I achieved communication between SDR console and my Ettus x310 (by going back to the old UHD Firmware 3.15) . Initially SDR console crashed after flashing when I started

There are TWO settings for windows firewall. One for public, one for private. I would start with disabling the firewall completely for both public and private at both the “server” computer and the

Hello Jolly, I still have problems getting the x310 to work. This morning I flashed succesfully the old firmware/imge from UHD 3.15. SDR console recognises now the X310 connected via 1G link, if

Good morning Erik, yes, the documentation could be better in particular for "OLD Man" like me.....with little software skills I wonder if I will get the X310 to communicate with SDR Console AFTER I

No, it’s the way the code is designed. UHD is a behemoth. Were I to have a Ettus for commercial use it’d write a support library for that actual device even though I would have to dig through

I'll believe that. But it was possible that the USB 3 port controller was in some data contention issues. RX888 going full speed would prove that. That's why I asked. {^_^}

Hi, Trust me – it’s the way UHD.dll is written ☹ . Simon Brown, G4ELI https://www.sdr-radio.com

That REALLY REALLY sounds like a firewall issue. Is your wireless network behind a NAT firewall of its own? (That is a nice secure way to handle it.) {^_^} On 20220202

Mumble mumble.... USB 3,0 was supposed to be about 500 MBps (BYTE/s). So it should support, just barely, a sample rate of 125 Msps for 16 bit I/Q samples. Is that 24 MHz a limit only

On Wed, Feb 2, 2022 at 06:38 PM, Dominic Dambro wrote: That's the way it's set up. And it works beautifully from any PC outside of my home network I try it on. (I'm logged into my station from work

That's the way it's set up. And it works beautifully from any PC outside of my home network I try it on. (I'm logged into my station from work right now.) It also works with any wired PC inside my