main@SDR-Radio.groups.io

Explanation Please - Satellite Passes

Greetings, Looking at NOAA 18. The large map information agrees with Orbitron, so two programs agreeing is great!. However the popup map, doesn't agree with the main map. The AOS values are

By George Stein - NJ3H · #64698 ·

Re: SDR Console with Airspy R2

Hi Simon, thanks for your reply (and for the one about satellite height as well) Hopefully the attached picture will help. All the best! Regards, George, NJ3H Redmond, Oregon USA

By George Stein - NJ3H · #64697 ·

Re: Malahit DSP and DSP2

The Malachit supports a very small subset of the Kenwood TS-480 command set. It supports reading the frequency and mode and setting only the frequency. It's severely limited in its scope. On the

By W4RLS · #64696 ·

Re: Malahit DSP and DSP2

I believe the Malahit supports a subset of the Kenwood CAT protocol through soapy library. Tuesday Oct 26, Malahiteam released their manuals in English for the original DSP1 and the DSP2:

By Larry Dighera · #64695 ·

Re: Malahit DSP and DSP2

Mike, I would consider it is there’s an IQ interface. Simon Brown, G4ELI https://www.sdr-radio.com

By Simon Brown · #64694 ·

Malahit DSP and DSP2

Simon, I do lots of outdoor listening when the weather cooperates and have stared using portable SDR receivers with the touch screen displays. You support the Afedri LAN-IQ SDR and have started to

By N2MS · #64693 ·

Re: SDR Console with Airspy R2

George, Adjust the contrast (RHS), just click [Auto], this will help a lot, then post a screenshot. Adjust the range with the Low and High options which are shown when the mouse is moved over the

By Simon Brown · #64692 ·

Re: Satellite Setup - Height

Height is just your height ASL. Makes a very, very small difference to the Doppler correction. Simon Brown, G4ELI https://www.sdr-radio.com

By Simon Brown · #64691 ·

Satellite Setup - Height

On the setup screen for home location for satellite reception, there is a data field called 'Height'. At first blush I would just enter the height above sea level for my location. However, there is

By George Stein - NJ3H · #64690 ·

Re: Satellite Push Buttons

Thanks, Max. That worked fine. I appreciate you help. Regards, George

By George Stein - NJ3H · #64689 ·

Re: SDR Console with Airspy R2

I have not used the satellite capability. {^_^} On 20211104 16:00:53, George Stein - NJ3H via groups.io wrote:

By jdow · #64688 ·

Re: SDR Console with Airspy R2

You are running SDRC at a substantially higher gain, I notice. (10 vs 6.) {^_^} On 20211104 15:38:34, George Stein - NJ3H via groups.io wrote:

By jdow · #64687 ·

Re: Satellite Push Buttons

Sorry, managed to insert picture in error as well as attach. Click second one (the attachment). It's bigger and more readable. Max

By Max · #64686 ·

Re: Satellite Push Buttons

See attached pic. First, press "Select" to left of the buttons you have circled. Then "Browse" and Favourites is a tick box option from which you can add to the push button list. Make sure "Add to

By Max · #64685 ·

Satellite Push Buttons

Kindly look at the attached picture. Notice the satellites buttons shown circled in red. Also notice the popup that shows a group called 'Favs'. How do I take my favs group and make them the push

By George Stein - NJ3H · #64684 ·

Re: SDR Console with Airspy R2

I find I have to run the gain on my R2 at 15 to 17 to get reasonable signal strengths, and clear reception. Here's the FM band on a 2M/440 antenna up 50' on my tower: 73 Kriss KA1GJU

By Kriss Kliegle KA1GJU · #64683 ·

Re: SDR Console with Airspy R2

I finally found the setting. Need to clean my glasses more often. Any suggested settings to maximize reception and quality using Console will be appreciated, JoAnne. Have you used the satellite

By George Stein - NJ3H · #64682 ·

Re: SDR Console with Airspy R2

Hi JoAnne, Thanks for your reply. The new SDRC picture is at 10 MHz bandwidth. The new SDR# is at 8 MHz bandwith. The audio has a lot of hiss in it using SDRC, while SDR# is crystal clear. Yes I am

By George Stein - NJ3H · #64681 ·

Re: SDR Console with Airspy R2

To a degree you are comparing apples and oranges. Zoom SDRC out all the way so it is showing roughly the same bandwidth as SDRSharp. Then don't cut off the edges of SDRC in your

By jdow · #64680 ·

SDR Console with Airspy R2

Greetings. I hope someone can help me with this issue. For the first time I am using my R2 with SDRC. I want to get it working to use with the satellite capability in SDRC. As you can see on the

By George Stein - NJ3H · #64679 ·

Messages