Jim is unusually experienced with audio cabling and hardware in high, that is really high, RF fields. He did sound for a theater located in a tall Chicago building that had very high power broadcast

Greetings, I have a basic question. Comparing the Perseus using its native software with the Perseus using SDRC, I hear more noise on the SDRC program than on the Perseus program. I am just curious

Hello Charlie, Yes of course, these hacks were done a long time ago. I am using my pluto without any issues on 2M with SDRANGEL. I am 100% confident the issue is with SDR-CONSOLE, I am a new user so

Hi, Did you record a single WAV RF64 file? Many programs don’t support this, so make sure you don’t have this option enabled. The SDR Console format is valid, just GnuRadio being lazy I

I'm using SDR Console to capture a sporadic signal with a LimeSDR by waiting to see it then hitting the record button in the record dialog. All seems to work well, but I need to start digging into

Another item i like is simple unmanaged switches with two fibre ports and 4/8/more copper ports, great for simple networking and even daisy chaining fibre (assuming 1.2G is

Michael, Easiest is to go Multimode duplex fibre and modules to suite. I'm no expert mind but here is what I am using (Ubiquiti was a bit cheaper for the modules than Mikrotik and I don't think there

Thanks everyone for the links and info! I bought a selection of the Chinese made snap-ons on eBay so I hope the quality will be suitable. I need them for the 5VDCpower supplies for my XHDATA D-808 and

That’s very interesting Stu. 73 Tom G6PZZ Nr Chesterfield | NE Derbyshire | UK | IO93he HF250 | RSPdx | Sentinel 4 | RM50 | TR2 15m MLB | MTA | D707

Stu, Informative postings, thanks. Could you post links to fibre and adapter info, please. Michael 2E0IHW

Either Cat6/7 OR add FT240-31 at both ends, good few turns. Ethernet radiates 60kHz spikes everywhere in the right conditions, to the point I'm mostly fibre now (in a tiny house). I once counted the

Thanks Jim If we have trouble I’ll get him CAT6. At least theholes in the ceiling will be there by then. You can see us at BH23 8DU. You can just about see my mastfor the 80m inverted V on the

Have you done the 'hack' to convert it to cover 144? Details here: https://wiki.analog.com/university/tools/pluto/users/customizing 73 Charlie G3WDG

On Sun, 19 Jul 2020 at 16:27, Peter Ide-Kostic <on7yi.pik973@...> wrote: Hello, I have the same problem. My pluto works file on RX (no issues) but when I measure the output power with a spectrum

I'd be using Cat 6. CAT5 is unscreened and I had RFI problems when using it and poor network performance when using it to carry HD quality. Switched to CAT6 which is

Hello, I have the same problem. My pluto works file on RX (no issues) but when I measure the output power with a spectrum analyzer, it is only -60 dBm..... with the drive set to 100%....The pluto is

Hello, I am a new user of sdr-console V3.0.23 I was able to make it work very quickly with my plutosdr in reception mode, no issues at all, great software It can transmit too, but the rf output power

Jim has a lot of very good antenna! 73, and thanks, Dave (NK7Z) https://www.nk7z.net ARRL Volunteer Examiner ARRL Technical Specialist ARRL Asst. Director, NW Division, Technical Resources

“I’m not entirely sure about the 50m cable behind the thatch though… it will be at right angles to my inverted V… will this pick up my 80m transmissions?” Allan, I’m not usually

FYI - myriadrf has a post from andrewback at : https://discourse.myriadrf.org/t/fix-in-lime-suite-for-limesdr-mini-loopback-test-failure/6311 "We had a number of reports of LimeSDR Mini boards