Simon: The problem has just gotten worse. I tried the full reset with no luck. I then deleted the program and reinstalled. It seemed to work OK at first but then it started to hang up again. Then

 Hi Sigi that can work after a fashion but it has the age-old problem you must under modulate with voice. If you hit the clipper with peaks it will strip off the CTCSS tone dropping you out of the

Hi Don, what microphone are you using with the pluto? Stefan

i anly have an idea for a workaround there are a dozen "tonegenerator" soft in the net (also double tone for imd measurement of a tx but thats another story) take one that can

I just got SDR console working with my PLUTOs and made few across the room contacts on 2M, 220, 440, 903, 1296, 2.5G, 3G and 5G! I would like to try hitting a few local repeaters but they have CTCSS

John, That’s very odd indeed. There’s a Full Reset option: https://www.sdr-radio.com/Support/FullReset this will probably get you going again. 3.0.4 and (soon) 3.0.5 resolve quite a few issues

SDRConsole v3.0.3 was running just fine until after I installed Simon's World Map program. The World Map program ran OK but now SDRConsole will not start. It would just hang and I could not shut it

Hi all. When I am activating my Lime SDR into Tx om Tx channel 1 using CW and "tune" and look at the modulation spectrum (using a HP 8561E SPA) I do not get one single tone but a whole spectrum

Joe When I start up, my Firmware Version on the console shows v1.08 I have updated to the latest Protocol 2. Does Protocol 2 Start with new version numbers? David Have you upgraded to Protocol 2 and

Hello Simon, I use an RSP2 and an RSP1A on two instances of SDR-Console. Would it be possible to include the name of the RX on the header of the satellite screen? It would help when there are two

Bug: With a ANAN-100 configured the antenna switch in the Home ribbon, the Icon shows the correct antenna selected position. But the pull down does not track the proper position. Switch does select

Looks like the panadapter slamming and the audio cutouts were due to version 1.6 of the firmware. Upgraded to v1.6Pre1 and that fixed those problems. Now just have a "freeze" that happens frequently

Hi Simon, Found a small bug: When leaving the Tone button on after transmitting and then changing the bandwidth e.g. from 2.1 to 2.5 MHz, then the Spectrum window in the Transmit Panel still

Looks like it’ll be tomorrow, I just want to sit on the code for another day. Simon Brown, G4ELI www.sdr-radio.com

Yes, thoughts 😊 When defining a CW filter you set the center frequency – aka ‘sweet spot’. Below the center frequency is 500Hz. Simon Brown, G4ELI www.sdr-radio.com

Wasn't aware of that. I can see how this can be useful with WSPR-X or similar applications if the timing of 'the other side' is a bit off. Cheers, Dick

Hi Joe, > (I am admin of my computers anyway \o/). Same here.. My issues with HDSDR and EXTIO was with the rtfsdr tcp dll. Do you mean ExtIO_RTL_TCP.dll v2016.3 ? If you ever tried to use

Dick, Yes I wrote that some time ago with an earlier version of WSJT-X, I guess WSJT-X may have changed or it was something in my setup. All I remember was that I had problems and "solved" them by

Dick, Actually i was thinking of RSNTP which is not installed as a service. It has timeshift facilities which can be useful at times, pun not intended:-) 73 Alan G4ZFQ

I'm currently using SDRConsole 3.0.4. In setting up a 2.7K CW filter, I cannot find a setting that maintains a CW offset like the default filters of 1K and below. I’ve tried to input negative