HF+ arrived today. Can not get to install. Win7 Pro. When I plugged in HF+ windows had this message: USB DEVICE NOT RECOGNIZED One of the usb devices attached to this computer has malfunctioned, and

The 5Vdc switching power supply was the culprit. Swapped it out with a Samsung cell phone switcher for now while I take it apart and see if it can be cured. Winegard LNA-200 is the make and model if

Just found another RFI product in house, the OTA (Over The Air) HDTV amplifier in the attic. This one was driving me nuts for weeks on 160M! Time to find another one, that's RFI quiet! 73 Kriss

Mark, Sorry about that, I see that build does not have direct sampling support. Check here:

Hi Simon, Thanks for the Info, very Interesting! Augusto HB9TZA / I2JJR Il 07/02/2018 18:36, Simon Brown ha scritto:

Yes I know, I have used lot of such devices / softwares, and know how they are. Lingua took really a bit to be able to set it at its best, but that

I had SDR-Radio working until I tried to install rtl-sdr++ to enable Q-branch. How do I install and enable rtl_tcp and make it work with my RTL-SDR V3 dongle? I went to the site that Joe Puma

Sigi, The NR in mchf uses Spectral Noise Reduction, something I’m also working on for version 3.1 . I have it working but it’s not yet ready for prime time. I haven’t used mchf so can’t

the dsp in mchf (and also in the named other external devices like lingua etc etc) can not dig out a signal that is not readable without (complete burried in noise) ... it just can help a

Oh yes I was looking on the M0NKA page short after posting my message, and I feel it's very interesting. Sorry to see oncemore the idea stolen for eastbiznez ...

😊 Seems to be more-or-less OK, I’ll not get some of the external radio support finished though, but this will be in beta 2. Simon Brown, G4ELI

you never heard of the mchf??? www.m0nka.co.uk chris changed the design when changing from 0.6 to 0.7 version of his boards i liked more the older design 0.3 to 0.6 boards (we

I try to open the pack but one srew-torax is blocked. I think you are right 5 cells it is most likely. After charging the voltage is 19.14 Volt. Connecting to the laptop: 20.14 V / 1.17 A 20 sec.

Mark, I just installed version 3 using RTL SDR. The dongle wasn’t be recognized by any of the software, following the recommended practice on the SDR Radio site for

Warnings on my V1.5 and 2.3 SDR Servers about the pending upgrade to V3 have been posted. Counting down the days... 73 Kriss KA1GJU

HI Siegfried, MCHF? I do not know it; "muscled" seems vy interesting, keep me informed pse. I also used a Archos 7", android 4, with companion bluetooth

check if the makita is not 5 cell 5x 3.6 18v nominal max voltage is 4.2 per cell 5x4.2 = 21v if it would be a 6 cell pack then 6x4.2 =25.2 ... but then makita would not write 18v on it cause a

Using a power pack from a drilling machine the battery icon in the system tray shows the plug. On de power pack : Metabo Li-Power 18V-2.2Ah The lowest value of a Li-Ion cell is 3 Volt and max 3.7

augusto just use the mchf instead cw decode on screen rtty rx and tx with no pc psk31, 63,125 .. rx and tx with no pc .... plus freedv!! (digital voice over shortwave)

The specific voltage regulator chips in alaptop will determine the minimum voltage acceptable at the power input socket. There are likely to be several differentchips and typically an older 12 volt