Date   

QRK Listen and Log Proposal #suggestion

wb9raa@...
 

 I am exciting about a new proposal 
 
 
 
Hello,
I need people with SDRs will to help with this. 
I am looking for feedback comment and volunteers to implement this !

Read my proposal below.  

Thank you 
 
73,  Ed March, WB9RAA
Prescott Valley, AZ
 
 
 


ServerManager #request #sdrserver

eyilmaz
 
Edited

Hello,

For the server:
- incoming port 50101 (TCP)
- outgoing port 50199 (TCP)

*** I changed incoming port to 2000. This is open. The others, allmost every port is "closed".

And port forwarding.

On the manager window on PC, everything is ok.
On the server map, I'm fine.

But no connection to me.

On youseeme, changed port to 8291 looks (today) timed out. Yesterday it was "open".

I'm living in a internet stricted country.

There is something missing I think. A UDP port or TCP ????

Thank you.

 

*** edited. Addep port 2000 part


Multi-Band Display

Simon Brown
 

So,

 

Here’s something I added a couple of years ago but never finished so it’s not available. What it needs is a layout / configuration window which includes the ability to have different window sizes as well as frequency ranges.

 

I’ll maybe look at this again as a solution to Ingolf, SM6FHZ’s wishes.

 

Simon Brown, G4ELI

https://www.sdr-radio.com

 


--
- + - + -
Please use https://forum.sdr-radio.com:4499/ when posting questions or problems.


Re: Keeping Tuned Freq in Center

Simon Brown
 

OK,

 

I did start a multi-band display which is what you want. This multi-band display is not available, I’ll re-visit it and see how much work would be needed.

 

Simon Brown, G4ELI

https://www.sdr-radio.com

 

From: main@SDR-Radio.groups.io <main@SDR-Radio.groups.io> On Behalf Of sm6fhz
Sent: 22 September 2021 21:41
To: main@SDR-Radio.groups.io
Subject: Re: [SDR-Radio] Keeping Tuned Freq in Center

 

OK Simon.
I will try to explain.
I have the Rx-matrix set up for a few sub-bands e.g. 70 cm CW (e.g. 432.020 to 432.070), 70 cm SSB (e.g. 432.150 to 432.250), 70 cm beacons etc.
I monitor these selected frequency ranges by these receivers in the Rx-matrix in order to see if any activity arises. E.G. in an contest situation.
If I see someone coming on I would like to move the Rx-passband to this frequency to listen, but still have the same monitoring (visually in spectrum and waterfall) as before.
I.E. locking the frequency band even if I move the Rx-frequency within this band. E.G. a check box for "lock Rx-matrix) so I still watch the same frequency range as set even if i scroll around listening to different stations.
I know this is the way the main window works, but there you do not get enough frequency resolution to separate different CW stations in the CW part of the band when looking at 432.000 to 432.500. That is why I use the Rx-matrix to display sub-bands of interest.
I have searched the "Options" for this but not found this possibility.
I hope I was able to explain my desire in an comprehensible way.
It would be very handy with such an option.
73 / Ingolf, SM6FHZ


--
- + - + -
Please use https://forum.sdr-radio.com:4499/ when posting questions or problems.


Re: 2365 Beta won't start the RSPduo. This worked fine in version 2346 #bug

Simon Brown
 

Well,

 

I’ve just run against 3.07 and 3.08 and with both it’s fine at 10MHz. From the log files being sent to me I don’t see any errors – the API service just doesn’t return data. I’ll check the 3.08 API documentation…

 

Simon Brown, G4ELI

https://www.sdr-radio.com

 

From: main@SDR-Radio.groups.io <main@SDR-Radio.groups.io> On Behalf Of Dennis Matzen
Sent: 22 September 2021 23:16
To: main@SDR-Radio.groups.io
Subject: Re: [SDR-Radio] 2365 Beta won't start the RSPduo. This worked fine in version 2346 #bug

 

Just ungraded the API on my laptop from 3.07 to 3.08 (I first un-installed all SDRPlay software and installed SDRuno 1.41). 

API service was set to auto-start and does (even after reboot). No need to run SDRuno first.

Also checked to see if I can run at 10Mhz bandwidth on this system (laptop) and cannot. * or below are OK as is on desktop.
--
Dennis
KA6FUB


--
- + - + -
Please use https://forum.sdr-radio.com:4499/ when posting questions or problems.


Re: Keeping Tuned Freq in Center

Simon Brown
 

Sorry,

 

Try this link

 

Simon Brown, G4ELI

https://www.sdr-radio.com

 

-----Original Message-----
From: main@SDR-Radio.groups.io <main@SDR-Radio.groups.io> On Behalf Of Simon Brown
Sent: 23 September 2021 06:39
To: main@SDR-Radio.groups.io
Subject: Re: [SDR-Radio] Keeping Tuned Freq in Center

 

£600k?

 

https://www.rightmove.co.uk/property-for-sale/find.html?locationIdentifier=R

EGION%5E16928&radius=0.5&propertyTypes=&includeSSTC=true&mustHave=&dontShow=

&furnishTypes=&keywords=

 

 

Simon Brown, G4ELI

https://www.sdr-radio.com

 

-----Original Message-----

From: main@SDR-Radio.groups.io <main@SDR-Radio.groups.io> On Behalf Of Mag loop Simon

Sent: 22 September 2021 20:55

To: main@sdr-radio.groups.io

Subject: Re: [SDR-Radio] Keeping Tuned Freq in Center

 

Hi Simon

 

GOOD NEWS House has been valued..

 

Much more than expected!!  Heading Saltash!! ( area) soon we hope!!

 

See you soon Other Simon

 

Sorry for post hijack..( ps Cornwall amp is made and working well!)

 

Seriously pls look out for properties circa 400k..promise wont come and visit..ps will take bribes to move to Norfolk..

 

 

 

 

 

 

 

 

--

- + - + -

Please use https://forum.sdr-radio.com:4499/ when posting questions or problems.

 

 

 

 


--
- + - + -
Please use https://forum.sdr-radio.com:4499/ when posting questions or problems.


Re: Keeping Tuned Freq in Center

Simon Brown
 

£600k?

https://www.rightmove.co.uk/property-for-sale/find.html?locationIdentifier=R
EGION%5E16928&radius=0.5&propertyTypes=&includeSSTC=true&mustHave=&dontShow=
&furnishTypes=&keywords=


Simon Brown, G4ELI
https://www.sdr-radio.com

-----Original Message-----
From: main@SDR-Radio.groups.io <main@SDR-Radio.groups.io> On Behalf Of Mag
loop Simon
Sent: 22 September 2021 20:55
To: main@sdr-radio.groups.io
Subject: Re: [SDR-Radio] Keeping Tuned Freq in Center

Hi Simon

GOOD NEWS House has been valued..

Much more than expected!! Heading Saltash!! ( area) soon we hope!!

See you soon Other Simon

Sorry for post hijack..( ps Cornwall amp is made and working well!)

Seriously pls look out for properties circa 400k..promise wont come and
visit..ps will take bribes to move to Norfolk..








--
- + - + -
Please use https://forum.sdr-radio.com:4499/ when posting questions or problems.


Re: Keeping Tuned Freq in Center

jdow
 

That explains a lot. There is no way to do this with SDRC as it's presently designed. So please disregard my prior responses about options.

With multiple receivers you might get away with setting two to the same frequency and using one as a movable tuning window while the other is muted and showing the chunk
of spectrum of interest. To be sure this is clumsy; but, it might approximate what it appears you want. (Fixed tuned matrix receivers.)

{^_^}

On 20210922 13:41:14, sm6fhz wrote:
OK Simon.
I will try to explain.
I have the Rx-matrix set up for a few sub-bands e.g. 70 cm CW (e.g. 432.020 to 432.070), 70 cm SSB (e.g. 432.150 to 432.250), 70 cm beacons etc.
I monitor these selected frequency ranges by these receivers in the Rx-matrix in order to see if any activity arises. E.G. in an contest situation.
If I see someone coming on I would like to move the Rx-passband to this frequency to listen, but still have the same monitoring (visually in spectrum and waterfall) as before.
I.E. locking the frequency band even if I move the Rx-frequency within this band. E.G. a check box for "lock Rx-matrix) so I still watch the same frequency range as set even if i scroll around listening to different stations.
I know this is the way the main window works, but there you do not get enough frequency resolution to separate different CW stations in the CW part of the band when looking at 432.000 to 432.500. That is why I use the Rx-matrix to display sub-bands of interest.
I have searched the "Options" for this but not found this possibility.
I hope I was able to explain my desire in an comprehensible way.
It would be very handy with such an option.
73 / Ingolf, SM6FHZ


Re: Keeping Tuned Freq in Center

jdow
 

Tour it slowly. When you get down to Tuning slow down and read. The first radio button selection may be as close as you get to what you want.

{^_^}

On 20210922 12:08:17, sm6fhz wrote:
I am sorry Joanne, but I can not find the setting you are referring to under "Tools", "Options".
Can you please post a screenshot to ease the finding of this particular setting enabling one singe receiver in the Rx-matrix to keep it's displayed frequency range even if I change the Rx-frequency within the displayed frequency range.
73 / Ingolf, SM6FHZ


Re: 2365 Beta won't start the RSPduo. This worked fine in version 2346 #bug

Dennis Matzen
 

Just ungraded the API on my laptop from 3.07 to 3.08 (I first un-installed all SDRPlay software and installed SDRuno 1.41). 

API service was set to auto-start and does (even after reboot). No need to run SDRuno first.

Also checked to see if I can run at 10Mhz bandwidth on this system (laptop) and cannot. * or below are OK as is on desktop.
--
Dennis
KA6FUB


Re: Keeping Tuned Freq in Center

Siegfried Jackstien
 

i am guessing rx matrix could do the job very well

each of your receivers represent a sub band (in your example the cw portion and the ssb dx window) ... your main receiver couod be much wider (say you have a good sdr with 10 megs bw you can receive the complete 70cm band)

now yoi see asignal on rx 1 (a cw signal comes up) ... in the rx window press select ... your receiver window is not also in the if window (rx dsp box) ... in rx 1 and 2 you can use a bit wider view (see my screenshots) and in the if window you do the finetune

in my example i only used one receiver in full screewidth to show you the different zoom settings ... but you can use 2 or 3 receivers (subbands)

if you do not want the subbands to be retuned ... why not use a third receiver?!? (maybe thats your solution?!?)

use rx 1 and 2 and subbands ... main spectrum shows full bw that your sdr gives ... and rx3 is used as "working" receiver (can be tuned to any frequency without change the sub receivers 1+2 that you only use to "view" but not for receive)

just an idea

dg9bfc sigi

Am 22.09.2021 um 22:41 schrieb sm6fhz:

OK Simon.
I will try to explain.
I have the Rx-matrix set up for a few sub-bands e.g. 70 cm CW (e.g. 432.020 to 432.070), 70 cm SSB (e.g. 432.150 to 432.250), 70 cm beacons etc.
I monitor these selected frequency ranges by these receivers in the Rx-matrix in order to see if any activity arises. E.G. in an contest situation.
If I see someone coming on I would like to move the Rx-passband to this frequency to listen, but still have the same monitoring (visually in spectrum and waterfall) as before.
I.E. locking the frequency band even if I move the Rx-frequency within this band. E.G. a check box for "lock Rx-matrix) so I still watch the same frequency range as set even if i scroll around listening to different stations.
I know this is the way the main window works, but there you do not get enough frequency resolution to separate different CW stations in the CW part of the band when looking at 432.000 to 432.500. That is why I use the Rx-matrix to display sub-bands of interest.
I have searched the "Options" for this but not found this possibility.
I hope I was able to explain my desire in an comprehensible way.
It would be very handy with such an option.
73 / Ingolf, SM6FHZ


Re: 2365 Beta won't start the RSPduo. This worked fine in version 2346 #bug

Robin Francis
 

I have api 3.08 and RSPduo working fine at 10 MHZ. I don’t have Uno installed and api starts fine. This with 2365 Beta. Originally I couldn’t run 10 MHZ at all until I made sure internal USB hub only had RSP connected.

Robin

 

Sent from Mail for Windows

 


Re: 2365 Beta won't start the RSPduo. This worked fine in version 2346 #bug

Dennis Matzen
 

Pulled out the RSPduo and tested it. Same result as the RSP2pro, 8Mhz OK, 10Mhz nothing. Log files attached.

I have API 3.07 installed on system.

System is a Dell XPS8700, i7-4770 CPU, 16GB memory, NVIDIA GeForce GT635

USB connection is to PCI 3.0 adapter, w/connection to power supply, dedicated to SDR 
--
Dennis
KA6FUB


Re: Keeping Tuned Freq in Center

sm6fhz
 

OK Simon.
I will try to explain.
I have the Rx-matrix set up for a few sub-bands e.g. 70 cm CW (e.g. 432.020 to 432.070), 70 cm SSB (e.g. 432.150 to 432.250), 70 cm beacons etc.
I monitor these selected frequency ranges by these receivers in the Rx-matrix in order to see if any activity arises. E.G. in an contest situation.
If I see someone coming on I would like to move the Rx-passband to this frequency to listen, but still have the same monitoring (visually in spectrum and waterfall) as before.
I.E. locking the frequency band even if I move the Rx-frequency within this band. E.G. a check box for "lock Rx-matrix) so I still watch the same frequency range as set even if i scroll around listening to different stations.
I know this is the way the main window works, but there you do not get enough frequency resolution to separate different CW stations in the CW part of the band when looking at 432.000 to 432.500. That is why I use the Rx-matrix to display sub-bands of interest.
I have searched the "Options" for this but not found this possibility.
I hope I was able to explain my desire in an comprehensible way.
It would be very handy with such an option.
73 / Ingolf, SM6FHZ


Re: Keeping Tuned Freq in Center

Mag loop Simon
 

Hi Simon

GOOD NEWS House has been valued..

Much more than expected!! Heading Saltash!! ( area) soon we hope!!

See you soon Other Simon

Sorry for post hijack..( ps Cornwall amp is made and working well!)

Seriously pls look out for properties circa 400k..promise wont come and visit..ps will take bribes to move to Norfolk..


Re: Keeping Tuned Freq in Center

Simon Brown
 

My mistake.

 

You’ll have to explain exactly what you want, it may be possible…

 

Simon Brown, G4ELI

https://www.sdr-radio.com

 

From: main@SDR-Radio.groups.io <main@SDR-Radio.groups.io> On Behalf Of sm6fhz
Sent: 22 September 2021 20:23
To: main@SDR-Radio.groups.io
Subject: Re: [SDR-Radio] Keeping Tuned Freq in Center

 

Hi Simon.
If your answer was for me and my question, it does not solve my question regarding the RX-matrix and locking one particular Rx-displayed frequency range and move your Rx withing that range keeping the very same frequency range displayed.
I was not sure if your answer was directed to me or to another question. Sorry.
73 / Ingolf, SM6FHZ


--
- + - + -
Please use https://forum.sdr-radio.com:4499/ when posting questions or problems.


Re: Keeping Tuned Freq in Center

sm6fhz
 

Hi Simon.
If your answer was for me and my question, it does not solve my question regarding the RX-matrix and locking one particular Rx-displayed frequency range and move your Rx withing that range keeping the very same frequency range displayed.
I was not sure if your answer was directed to me or to another question. Sorry.
73 / Ingolf, SM6FHZ


Re: RSPdx will not start in SDRC 3.1 Build 2365 #sdruno

Simon Brown
 

Also,

 

I can start any RSP receiver without every using SDRuno, in fact I’ve never installed SDRuno, only the API downloads. Maybe SDRuno starts the service? I can always do this myself.

 

Simon Brown, G4ELI

https://www.sdr-radio.com

 

From: main@SDR-Radio.groups.io <main@SDR-Radio.groups.io> On Behalf Of milairuk via groups.io
Sent: 22 September 2021 19:56
To: main@SDR-Radio.groups.io
Subject: [SDR-Radio] RSPdx will not start in SDRC 3.1 Build 2365 #sdruno

 

I've just upgraded two PC's with SDRuno version 1.41 and now SDRC doesn't want to start my RSPDx unless I first start SDRuno. It appears that the problem is that the old API v3.07 loads at the startup of W10, whereas the latest API v3.08 doesn't. It can also be started in Services instead of running SDRuno first.
On one PC I have re-installed SDRuno 1.40 and then have no problems as the API is v3.07. Cannot work out why the new API v3.08 doesn't start even though it is set to Automatic in services ? Any ideas ?

Regards

John


--
- + - + -
Please use https://forum.sdr-radio.com:4499/ when posting questions or problems.


Re: RSPdx will not start in SDRC 3.1 Build 2365 #sdruno

Simon Brown
 

Hi,

 

I noticed that 3.08 was not set to automatic startup. You’ll have to bring this up with the SDRplay folks, it’s their API.

 

Simon Brown, G4ELI

https://www.sdr-radio.com

 

From: main@SDR-Radio.groups.io <main@SDR-Radio.groups.io> On Behalf Of milairuk via groups.io
Sent: 22 September 2021 19:56
To: main@SDR-Radio.groups.io
Subject: [SDR-Radio] RSPdx will not start in SDRC 3.1 Build 2365 #sdruno

 

I've just upgraded two PC's with SDRuno version 1.41 and now SDRC doesn't want to start my RSPDx unless I first start SDRuno. It appears that the problem is that the old API v3.07 loads at the startup of W10, whereas the latest API v3.08 doesn't. It can also be started in Services instead of running SDRuno first.
On one PC I have re-installed SDRuno 1.40 and then have no problems as the API is v3.07. Cannot work out why the new API v3.08 doesn't start even though it is set to Automatic in services ? Any ideas ?

Regards

John


--
- + - + -
Please use https://forum.sdr-radio.com:4499/ when posting questions or problems.


Re: Keeping Tuned Freq in Center

Simon Brown
 

Like this – see attachment.

 

Simon Brown, G4ELI

https://www.sdr-radio.com

 

From: main@SDR-Radio.groups.io <main@SDR-Radio.groups.io> On Behalf Of sm6fhz
Sent: 22 September 2021 20:08
To: main@SDR-Radio.groups.io
Subject: Re: [SDR-Radio] Keeping Tuned Freq in Center

 

I am sorry Joanne, but I can not find the setting you are referring to under "Tools", "Options".
Can you please post a screenshot to ease the finding of this particular setting enabling one singe receiver in the Rx-matrix to keep it's displayed frequency range even if I change the Rx-frequency within the displayed frequency range.
73 / Ingolf, SM6FHZ


--
- + - + -
Please use https://forum.sdr-radio.com:4499/ when posting questions or problems.

2361 - 2380 of 66344