Date   

Re: Accessing WWV

meso2303@...
 

If you have the RTL-SDR.com radio with HF frequencies included, then the dongle IS capable of HF frequencies, but only by direct sampling below 25 MHz (roughly, check the radio specs). If you search this group for "direct sampling", I found that direct sampling IS NOT supported by the SDR-Radio V3 program (yet?).
I can listen to WWV using direct sampling using SDR-Sharp.  See: https://www.rtl-sdr.com/rtl-sdr-blog-v-3-dongles-user-guide/
I'm sure there are other software options, but direct sampling ability is the key for HF with some dongles.
Here is an image of the settings that work for me:

Good luck!
Joe


Re: Trunk Voice Following

Simon Brown
 

Yes.

 

Simon Brown, G4ELI
www.sdr-radio.com

 

 

From: main@SDR-Radio.groups.io <main@SDR-Radio.groups.io> On Behalf Of Gary_Gagnon@...

 

:-)

 

Simon, you keep adding surprises and we are not complaining.

 

A possible UniTrunker replacement with the capability to let DSDPlus do some decoding?  I hope!

 

Gary


Re: Trunk Voice Following

Simon Brown
 

Hi,

 

Only one Radio is needed, monitors Controller and the Voice channels (up to 5 at the same time).

 

Simon Brown, G4ELI
www.sdr-radio.com

 

 

From: main@SDR-Radio.groups.io <main@SDR-Radio.groups.io> On Behalf Of vincent
Sent: 29 April 2018 23:09
To: main@sdr-radio.groups.io
Cc: SDR-Radio@groups.io
Subject: Re: [SDR-Radio] Trunk Voice Following

 

Simon,

Can you elaborate a little more, will you be able to use two SDR's, one for the control channel and one for voice following? OMG, this would be great to have this capability in Radio Console. 

Also will it be fir V3 also?


Vincent

 

On Sun, Apr 29, 2018 at 3:04 PM, Simon Brown <simon@...> wrote:

Coming to a Console near you next week.

 

https://en.wikipedia.org/wiki/Trunking

 

Unlike some other solutions this requires only one SDR receiver such as the Airspy or RSP1/1A/2.

 

Simon Brown, G4ELI
www.sdr-radio.com

 

 

 


Re: Trunk Voice Following

Gary_Gagnon@...
 

:-)

Simon, you keep adding surprises and we are not complaining.

A possible UniTrunker replacement with the capability to let DSDPlus do some decoding?  I hope!

Gary


From: "simon" <simon@...>
To: SDR-Radio@groups.io
Sent: Sunday, April 29, 2018 3:04:46 PM
Subject: [SDR-Radio] Trunk Voice Following

Coming to a Console near you next week.

 

https://en.wikipedia.org/wiki/Trunking

 

Unlike some other solutions this requires only one SDR receiver such as the Airspy or RSP1/1A/2.

 

Simon Brown, G4ELI
www.sdr-radio.com

 

 


Re: Trunk Voice Following

vincent
 

Simon,
Can you elaborate a little more, will you be able to use two SDR's, one for the control channel and one for voice following? OMG, this would be great to have this capability in Radio Console. 
Also will it be fir V3 also?

Vincent

On Sun, Apr 29, 2018 at 3:04 PM, Simon Brown <simon@...> wrote:

Coming to a Console near you next week.

 

https://en.wikipedia.org/wiki/Trunking

 

Unlike some other solutions this requires only one SDR receiver such as the Airspy or RSP1/1A/2.

 

Simon Brown, G4ELI
www.sdr-radio.com

 

 



Trunk Voice Following

Simon Brown
 

Coming to a Console near you next week.

 

https://en.wikipedia.org/wiki/Trunking

 

Unlike some other solutions this requires only one SDR receiver such as the Airspy or RSP1/1A/2.

 

Simon Brown, G4ELI
www.sdr-radio.com

 

 


Re: ELAD FDM s2 issue with V3

Tony_AD0VC
 

The only reason I knew what it was is because I have made this mistake too. Glad to help.


Tony




From: main@SDR-Radio.groups.io <main@SDR-Radio.groups.io> on behalf of Giuseppe Lati via Groups.Io <beppdigit@...>
Sent: Sunday, April 29, 2018 1:00 PM
To: main@SDR-Radio.groups.io
Subject: Re: [SDR-Radio] ELAD FDM s2 issue with V3
 
Hi,

many thanks Tony: it was as you wrote. Sorry to everybody for my carelessness.

73

Giuseppe 

On Sunday, April 29, 2018, 6:59:21 PM GMT+2, Ron Liekens <r.e.liekens@...> wrote:


Also no problems here with the FDM-S2.

73' Ron


Re: ELAD FDM s2 issue with V3

Giuseppe Lati <beppdigit@...>
 

Hi,

many thanks Tony: it was as you wrote. Sorry to everybody for my carelessness.

73

Giuseppe 

On Sunday, April 29, 2018, 6:59:21 PM GMT+2, Ron Liekens <r.e.liekens@...> wrote:


Also no problems here with the FDM-S2.

73' Ron


Re: ELAD FDM s2 issue with V3

Ron Liekens
 

Also no problems here with the FDM-S2.

73' Ron


Re: ELAD FDM s2 issue with V3

Tony_AD0VC
 

I am using the S2 with no problems. Make sure that, on the HOME, tab, that LPF 30Mhz is enabled. If it is off, you will see nothing on HF.


Tony

AD0VC




From: main@SDR-Radio.groups.io <main@SDR-Radio.groups.io> on behalf of Giuseppe Lati via Groups.Io <beppdigit@...>
Sent: Sunday, April 29, 2018 10:27 AM
To: main@SDR-Radio.groups.io
Subject: Re: [SDR-Radio] ELAD FDM s2 issue with V3
 
Hi,

as you can see from the picture, in practice, it appears only the noise floor of the ELAD and it looks like that through all the HF spectrum of receiver. Instead the ELAD works normally when I use the native or another freeware.
No problem when I use the Perseus with the V3.

Giuseppe

On Sunday, April 29, 2018, 3:05:30 PM GMT+2, Simon Brown <simon@...> wrote:


Hi,

 

What’s the problem?

 

Simon Brown, G4ELI
www.sdr-radio.com

www.sdr-radio.com
SDR-Radio.com development portal. Please do not send e-mail to the development team unless absolutely necessary.The fount of all knowledge is the Groups.io forum, several thousand happy members of this group are ready to help you.

 

 

From: main@SDR-Radio.groups.io <main@SDR-Radio.groups.io> On Behalf Of Giuseppe Lati via Groups.Io
Sent: 29 April 2018 10:17
To: main@sdr-radio.groups.io
Subject: [SDR-Radio] ELAD FDM s2 issue with V3

 

Hi Simon,

                my ELAD FDM-s2 (latest realised installed) is not working any more with the latest V3, despite any attempt to solve the issue.

Here attached you'll find a picture with the log.

 

Many thanks in advance for your assistance.

 

Best 73

 

Giuseppe


Re: ELAD FDM s2 issue with V3

Giuseppe Lati <beppdigit@...>
 

Hi,

as you can see from the picture, in practice, it appears only the noise floor of the ELAD and it looks like that through all the HF spectrum of receiver. Instead the ELAD works normally when I use the native or another freeware.
No problem when I use the Perseus with the V3.

Giuseppe

On Sunday, April 29, 2018, 3:05:30 PM GMT+2, Simon Brown <simon@...> wrote:


Hi,

 

What’s the problem?

 

Simon Brown, G4ELI
www.sdr-radio.com

 

 

From: main@SDR-Radio.groups.io <main@SDR-Radio.groups.io> On Behalf Of Giuseppe Lati via Groups.Io
Sent: 29 April 2018 10:17
To: main@sdr-radio.groups.io
Subject: [SDR-Radio] ELAD FDM s2 issue with V3

 

Hi Simon,

                my ELAD FDM-s2 (latest realised installed) is not working any more with the latest V3, despite any attempt to solve the issue.

Here attached you'll find a picture with the log.

 

Many thanks in advance for your assistance.

 

Best 73

 

Giuseppe


Re: Kit: Frequency Database April 22nd, 2018

Simon Brown
 

Hi,

 

Please send me the actual database you used and the frequency / name of a bad entry. Send to simon@... please.

 

Simon Brown, G4ELI
www.sdr-radio.com

 

 

From: main@SDR-Radio.groups.io <main@SDR-Radio.groups.io> On Behalf Of Herman Wijnants via Groups.Io
Sent: 29 April 2018 15:00
To: main@SDR-Radio.groups.io
Subject: [SDR-Radio] Kit: Frequency Database April 22nd, 2018

 

Hello,


I've been running the database from the fmlist for a while and it works nicely. Today I discovered that some entries from the csv

are not entered in the database due to a formatting issue. I tried to correct it, but no go.


Of course there are quite a few of these issues in the csv download from http://fmscan.org/perseus.php

 

Can this be fixed?


Kit: Frequency Database April 22nd, 2018

Herman Wijnants
 

Hello,

I've been running the database from the fmlist for a while and it works nicely. Today I discovered that some entries from the csv
are not entered in the database due to a formatting issue. I tried to correct it, but no go.


Of course there are quite a few of these issues in the csv download from http://fmscan.org/perseus.php

Can this be fixed?


Re: ELAD FDM s2 issue with V3

Simon Brown
 

Hi,

 

What’s the problem?

 

Simon Brown, G4ELI
www.sdr-radio.com

 

 

From: main@SDR-Radio.groups.io <main@SDR-Radio.groups.io> On Behalf Of Giuseppe Lati via Groups.Io
Sent: 29 April 2018 10:17
To: main@sdr-radio.groups.io
Subject: [SDR-Radio] ELAD FDM s2 issue with V3

 

Hi Simon,

                my ELAD FDM-s2 (latest realised installed) is not working any more with the latest V3, despite any attempt to solve the issue.

Here attached you'll find a picture with the log.

 

Many thanks in advance for your assistance.

 

Best 73

 

Giuseppe


ELAD FDM s2 issue with V3

Giuseppe Lati <beppdigit@...>
 

Hi Simon,
                my ELAD FDM-s2 (latest realised installed) is not working any more with the latest V3, despite any attempt to solve the issue.
Here attached you'll find a picture with the log.

Many thanks in advance for your assistance.

Best 73

Giuseppe


Re: USRP B2xx bandwidth

Kari Tuominen
 

Can you also fix LimeSDR mini please.
BW's are good up to 20mhz, 25 and 30 totally overloaded mess.


Re: USRP B2xx bandwidth

Simon Brown
 

Thanks.

 

The logfile shows everything, am asking Ettus support whether I can use the 56MHz clock rate with the b205 Mini.

 

Simon Brown, G4ELI
www.sdr-radio.com

 

 

From: main@SDR-Radio.groups.io <main@SDR-Radio.groups.io> On Behalf Of Andrew Hobgood
Sent: 28 April 2018 20:58
To: main@SDR-Radio.groups.io
Subject: Re: [SDR-Radio] USRP B2xx bandwidth

 

Apologies... logfile attached.  Let me know if you need any screenshots or additional logs.

/Andrew


Re: USRP B2xx bandwidth

Andrew Hobgood
 

Apologies... logfile attached.  Let me know if you need any screenshots or additional logs.

/Andrew


Re: USRP B2xx bandwidth

Simon Brown
 

Hi,

 

I need to see the logfile.

 

Simon Brown, G4ELI
www.sdr-radio.com

 

 

From: main@SDR-Radio.groups.io <main@SDR-Radio.groups.io> On Behalf Of Andrew Hobgood
Sent: 28 April 2018 16:15
To: main@SDR-Radio.groups.io
Subject: [SDR-Radio] USRP B2xx bandwidth

 

Hello Simon (and fellow enthusiasts) --

After unpacking my shiny new USRP B205mini and setting it up under Windows 10, I was delighted to find it discovered readily by SDR-Console v3.

Currently, however, there appears to be no way to select an IF bandwidth wider than 16MHz in the radio selection dialog.  The "Ettus Research" page on sdr-radio.com has the following note under the To-Do section:

  • Apply the UHD update (when available) to support up to 61MHz bandwidth from the B200.

I'm simply curious if this update is expected soon.  Does the current UHD release have the necessary components or is there something needed from Ettus?  The program and device work together flawlessly otherwise over USB3 (maxing out on USB2 at 8MHz before stuttering).

Thanks!

/Andrew

 


USRP B2xx bandwidth

Andrew Hobgood
 

Hello Simon (and fellow enthusiasts) --

After unpacking my shiny new USRP B205mini and setting it up under Windows 10, I was delighted to find it discovered readily by SDR-Console v3.

Currently, however, there appears to be no way to select an IF bandwidth wider than 16MHz in the radio selection dialog.  The "Ettus Research" page on sdr-radio.com has the following note under the To-Do section:

  • Apply the UHD update (when available) to support up to 61MHz bandwidth from the B200.
I'm simply curious if this update is expected soon.  Does the current UHD release have the necessary components or is there something needed from Ettus?  The program and device work together flawlessly otherwise over USB3 (maxing out on USB2 at 8MHz before stuttering).

Thanks!

/Andrew